7针0.96寸OLED的HAL库代码(硬件SPI/全代码/stm32f1/CubeMX配置/包含有正负浮点数/100%一次点亮)

这篇具有很好参考价值的文章主要介绍了7针0.96寸OLED的HAL库代码(硬件SPI/全代码/stm32f1/CubeMX配置/包含有正负浮点数/100%一次点亮)。希望对大家有所帮助。如果存在错误或未考虑完全的地方,请大家不吝赐教,您也可以点击"举报违法"按钮提交疑问。

系列文章链接

HC-SR04超声波模块的使用

 编码电机以及双电机驱动

4针 0.96'OLED的使用

更多有意思的文章点击“我的主页”
--------😐
更多有意思的视频 -----> B站 @想要亿只独角兽
--------😐


 前言

  • 之前发布了一篇硬件I2C的0.96' OLED驱动代码,这次就添加一篇硬件SPI的驱动代码。

其实改动的代码不多,对下面两个写命令和写数据的函数稍加改动即可。 

void OLED_WR_DATA(uint8_t data) 和 void OLED_WR_CMD(uint8_t cmd)


目录

系列文章链接

 前言

一、OLED驱动的基本功能

二、CubeMX中的设置

2.1.  配置时钟树

2.2.  配置硬件SPI

2.3.  接线以及最终管脚图

三、代码

3.1.  oled.c

3.2.  oled.h

3.3.  oledfont.c

3.4.  oledfont.h

3.5. main.h

3.6. main.c (仅测试使用)

四、推荐学习

总结



一、OLED驱动的基本功能

跟I2C那篇驱动代码的功能一致,这里再叙述一下。。。

1.可以正反相显示8X16,6x8的字符,数字,字符串
2.可以正反相显示16X16的汉字
3.可以正反相显示任意大小的图像
4.全屏水平滚动播放,部分屏幕水平滚动播放 ,全屏垂直水平滚动播放
5. 屏幕亮度调节,屏幕内容取反显示
6. 可以正反相显示8X16,6x8的正负浮点数


7针0.96寸OLED的HAL库代码(硬件SPI/全代码/stm32f1/CubeMX配置/包含有正负浮点数/100%一次点亮),STM32常见外设的使用,stm32,单片机,嵌入式硬件,arm

二、CubeMX中的设置

2.1.  配置时钟树

(1)点击RCC 开启HSE,并选择RC或晶体作为时钟源

7针0.96寸OLED的HAL库代码(硬件SPI/全代码/stm32f1/CubeMX配置/包含有正负浮点数/100%一次点亮),STM32常见外设的使用,stm32,单片机,嵌入式硬件,arm


(2)配置时钟树

 7针0.96寸OLED的HAL库代码(硬件SPI/全代码/stm32f1/CubeMX配置/包含有正负浮点数/100%一次点亮),STM32常见外设的使用,stm32,单片机,嵌入式硬件,arm

最终最右侧显示为

7针0.96寸OLED的HAL库代码(硬件SPI/全代码/stm32f1/CubeMX配置/包含有正负浮点数/100%一次点亮),STM32常见外设的使用,stm32,单片机,嵌入式硬件,arm


2.2.  配置硬件SPI

需要配置的参数如下:

*********************************************************
*   引脚定义:                                         
*   OLED_CS  OLED_RES  OLED_DC   :OUTPUT  Output push pull
*********************************************************
*   SPI定义:                                          
*   Mode:Transmit only Master                          
*   Hardware Nss Signal:Disable                        
*   Data Size : 8Bits                                  
*   First Bit : MSB First                              
*   CPOL : Low                                         
*   CPHA : 1 Edge	 
*********************************************************

(1)选择SPI1;

将模式选择为 Transmit only Master (主机发送,从机接收);Hardware Nss Signal:  Disable

7针0.96寸OLED的HAL库代码(硬件SPI/全代码/stm32f1/CubeMX配置/包含有正负浮点数/100%一次点亮),STM32常见外设的使用,stm32,单片机,嵌入式硬件,arm


(2)SPI参数设定

其中时钟的预分频系数Prescaler可以设置的小一些,这样对应的波特率Baud Rate 就会比较大,相应的直观感受是OLED刷新的速度很快,屏闪感受变小。

7针0.96寸OLED的HAL库代码(硬件SPI/全代码/stm32f1/CubeMX配置/包含有正负浮点数/100%一次点亮),STM32常见外设的使用,stm32,单片机,嵌入式硬件,arm


(3)GPIO配置 

7针0.96寸OLED的HAL库代码(硬件SPI/全代码/stm32f1/CubeMX配置/包含有正负浮点数/100%一次点亮),STM32常见外设的使用,stm32,单片机,嵌入式硬件,arm

 PB0、PB1、PB10 都设置为 初始低电平,推挽输出,无上下拉电阻,高速输出 的模式 

7针0.96寸OLED的HAL库代码(硬件SPI/全代码/stm32f1/CubeMX配置/包含有正负浮点数/100%一次点亮),STM32常见外设的使用,stm32,单片机,嵌入式硬件,arm

7针0.96寸OLED的HAL库代码(硬件SPI/全代码/stm32f1/CubeMX配置/包含有正负浮点数/100%一次点亮),STM32常见外设的使用,stm32,单片机,嵌入式硬件,arm


(4)烧录选SWD

7针0.96寸OLED的HAL库代码(硬件SPI/全代码/stm32f1/CubeMX配置/包含有正负浮点数/100%一次点亮),STM32常见外设的使用,stm32,单片机,嵌入式硬件,arm


2.3.  接线以及最终管脚图

********************************************************
*   接线:                                             
*   GND ---> GND                                       
*   VCC ---> 3.3V                                      
*   DO  ---> SPI_SCK       PA5                            
*   D1  ---> SPI_MOSI      PA7                            
*   RES ---> OLED_RES      PB0                            
*   DC  ---> OLED_DC       PB1                            
*   CS  ---> OLED_CS       PB10                            
*                                                                                                    
********************************************************

7针0.96寸OLED的HAL库代码(硬件SPI/全代码/stm32f1/CubeMX配置/包含有正负浮点数/100%一次点亮),STM32常见外设的使用,stm32,单片机,嵌入式硬件,arm


三、代码

3.1.  oled.c

7针0.96寸OLED的HAL库代码(硬件SPI/全代码/stm32f1/CubeMX配置/包含有正负浮点数/100%一次点亮),STM32常见外设的使用,stm32,单片机,嵌入式硬件,arm

>注:
> 1.上图中 Set Charge Pump (设置电荷泵)设置为0x8D,0x10即关闭了电荷泵;而程序中笔者开启了电荷泵,故设置为0x8D,0x14。而且把这一步放置在了初始化的最后。
> 2.笔者的初始化程序在对比度设置(红色字体处),预充电持续时间等数值大小上与上图不同,其实只要初始化思路一致,这些差异不会影响OLED的使用,这些个性化设置还需好好参读芯片手册**
 

/********************************************************/
/*   2022/9/30                                     
*   Unicorn_Yihao                                       
*   STM32 7针硬件SPI 0.96 OLED HAL库显示驱动   
*********************************************************
*   引脚定义:                                         
*   OLED_CS OLED_RES OLED_DC OUTPUT    Output push pull
*********************************************************
*   SPI定义:                                          
*   Mode:Transmit only Master                          
*   Hardware Nss Signal:Disable                        
*   Data Size : 8Bits                                  
*   First Bit : MSB First                              
*   CPOL : Low                                         
*   CPHA : 1 Edge	 
*********************************************************
*   接线:                                             
*   GND ---> GND                                       
*   VCC ---> 3.3V                                      
*   DO  ---> SPI_SCK       PA5                            
*   D1  ---> SPI_MOSI      PA7                            
*   RES ---> OLED_RES      PB0                            
*   DC  ---> OLED_DC       PB1                            
*   CS  ---> OLED_CS       PB10                            
*                                                      
*/                                                     
/********************************************************/

#include "oled.h"

/**********************************************************
 * 初始化命令,根据芯片手册书写
 ***********************************************************/
uint8_t OLED_Init_CMD_Data[]={
0xAE, 0xD5, 0x80, 0xA8, 0x3F, 0xD3, 0x00, 0x40,0xA1, 0xC8, 0xDA,

0x12, 0x81, 0xCF, 0xD9, 0xF1, 0xDB, 0x40, 0xA4, 0xA6,0x8D, 0x14,

0xAF};



/**
 * @function: void OLED_Init(void)
 * @description: OLED初始化
 * @return {*}
 */
void OLED_Init(void)
{

	OLED_RES_Clr();
	HAL_Delay(200);
	OLED_RES_Set();
	
	uint8_t i = 0;  
	for(i=0; i<23; i++)
	{
		OLED_WR_CMD(OLED_Init_CMD_Data[i]);
	}

}


/**
 * @function: void OLED_WR_CMD(uint8_t cmd)
 * @description: 向设备写控制命令
 * @param {uint8_t} cmd 芯片手册规定的命令
 * @return {*}
 */
void OLED_WR_CMD(uint8_t cmd)
{
	 OLED_DC_Clr();
	 OLED_CS_Clr();
	 HAL_SPI_Transmit(&hspi1,&cmd,1,100); //需根据实际情况修改 
	 OLED_CS_Set();
	 OLED_DC_Set();   	  
}

/**
 * @function: void OLED_WR_DATA(uint8_t data)
 * @description: 向设备写控制数据
 * @param {uint8_t} data 数据
 * @return {*}
 */
void OLED_WR_DATA(uint8_t data)
{
	 OLED_DC_Set();  
	 OLED_CS_Clr();
	 HAL_SPI_Transmit(&hspi1,&data,1,100); //需根据实际情况修改 
	 OLED_CS_Set();
	 OLED_DC_Set();   	  
}

/**
 * @function: void OLED_On(void)
 * @description: 更新显示

 * @return {*}
 */
void OLED_On(void)
{
	uint8_t i,n;
	for(i=0;i<8;i++)
	{
		OLED_WR_CMD(0xb0+i);    //设置页地址(0~7)
		OLED_WR_CMD(0x00);      //设置显示位置—列低地址
		OLED_WR_CMD(0x10);      //设置显示位置—列高地址
		for(n=0;n<128;n++)
			OLED_WR_DATA(1);
	}
}


/**
 * @function: OLED_Clear(void)
 * @description: 清屏,整个屏幕是黑色的!和没点亮一样!!!
 * @return {*}
 */
void OLED_Clear(void)
{
	uint8_t i,n;
	for(i=0;i<8;i++)
	{
		OLED_WR_CMD(0xb0+i);    //设置页地址(0~7)
		OLED_WR_CMD(0x00);      //设置显示位置—列低地址
		OLED_WR_CMD(0x10);      //设置显示位置—列高地址
		for(n=0;n<128;n++)
			OLED_WR_DATA(0);
	}
}

/**
 * @function: void OLED_Display_On(void)
 * @description: 开启OLED显示
 * @return {*}
 */
void OLED_Display_On(void)
{
	OLED_WR_CMD(0X8D);  //SET DCDC命令
	OLED_WR_CMD(0X14);  //DCDC ON
	OLED_WR_CMD(0XAF);  //DISPLAY ON,打开显示
}


/**
 * @function: void OLED_Display_Off(void)
 * @description: 关闭OLED显示
 * @return {*}
 */
void OLED_Display_Off(void)
{
	OLED_WR_CMD(0X8D);  //SET DCDC命令
	OLED_WR_CMD(0X10);  //DCDC OFF
	OLED_WR_CMD(0XAE);  //DISPLAY OFF,关闭显示
}

/**
 * @function: void OLED_Set_Pos(uint8_t x, uint8_t y)
 * @description: 坐标设置
 * @param {uint8_t} x,y
 * @return {*}
 */
void OLED_Set_Pos(uint8_t x, uint8_t y)
{
	OLED_WR_CMD(0xb0+y);	//设置页地址(0~7)
	OLED_WR_CMD(((x&0xf0)>>4)|0x10); //设置显示位置—列高地址
	OLED_WR_CMD(x&0x0f);	//设置显示位置—列低地址
}


/**
 * @function: unsigned int oled_pow(uint8_t m,uint8_t n)
 * @description: m^n函数
 * @param {uint8_t} m,n
 * @return {unsigned int} result
 */
unsigned int oled_pow(uint8_t m,uint8_t n)
{
	unsigned int result=1;
	while(n--)result*=m;
	return result;
}

/**
 * @function: void OLED_ShowChar(uint8_t x, uint8_t y, uint8_t chr, uint8_t Char_Size,uint8_t Color_Turn)
 * @description: 在OLED12864特定位置开始显示一个字符
 * @param {uint8_t} x字符开始显示的横坐标
 * @param {uint8_t} y字符开始显示的纵坐标
 * @param {uint8_t} chr待显示的字符
 * @param {uint8_t} Char_Size待显示字符的字体大小,选择字体 16/12
 * @param {uint8_t} Color_Turn是否反相显示(1反相、0不反相)
 * @return {*}
 */
void OLED_ShowChar(uint8_t x,uint8_t y,uint8_t chr,uint8_t Char_Size,uint8_t Color_Turn)
{
	unsigned char c=0,i=0;
		c=chr-' ';//得到偏移后的值
		if(x>128-1){x=0;y=y+2;}
		if(Char_Size ==16)
		{
			OLED_Set_Pos(x,y);
			for(i=0;i<8;i++)
				{
				  if(Color_Turn)
					  OLED_WR_DATA(~F8X16[c*16+i]);
				  else
					  OLED_WR_DATA(F8X16[c*16+i]);
				}
			OLED_Set_Pos(x,y+1);
			for(i=0;i<8;i++)
			    {
				  if(Color_Turn)
					  OLED_WR_DATA(~F8X16[c*16+i+8]);
				  else
					  OLED_WR_DATA(F8X16[c*16+i+8]);
			    }

			}
	     else
	     {
				OLED_Set_Pos(x,y);
				for(i=0;i<6;i++)
			    {
				  if(Color_Turn)
					  OLED_WR_DATA(~F6x8[c][i]);
				  else
					  OLED_WR_DATA(F6x8[c][i]);
			    }
		  }
}

/**
 * @function: void OLED_ShowString(uint8_t x, uint8_t y, uint8_t *chr, uint8_tChar_Size, uint8_t Color_Turn)
 * @description: 在OLED12864特定位置开始显示字符串
 * @param {uint8_t} x待显示字符串的开始横坐标x:0~127
 * @param {uint8_t} y待显示字符串的开始纵坐标 y:0~7,若选择字体大小为16,则两行数字之间需要间隔2,若选择字体大小为12,间隔1
 * @param {uint8_t} *chr待显示的字符串
 * @param {uint8_t} Char_Size待显示字符串的字体大小,选择字体 16/12,16为8X16,12为6x8
 * @param {uint8_t} Color_Turn是否反相显示(1反相、0不反相)
 * @return {*}
 */
void OLED_ShowString(uint8_t x,uint8_t y,char *chr,uint8_t Char_Size, uint8_t Color_Turn)
{
	uint8_t  j=0;
	while (chr[j]!='\0')
	{		OLED_ShowChar(x,y,chr[j],Char_Size, Color_Turn);
			if (Char_Size == 12) //6X8的字体列加6,显示下一个字符
				x += 6;
			else  //8X16的字体列加8,显示下一个字符
				x += 8;

			if (x > 122 && Char_Size==12) //TextSize6x8如果一行不够显示了,从下一行继续显示
			{
				x = 0;
				y++;
			}
			if (x > 120 && Char_Size== 16) //TextSize8x16如果一行不够显示了,从下一行继续显示
			{
				x = 0;
				y++;
			}
			j++;
	}
}

/**
 * @function: void OLED_ShowNum(uint8_t x,uint8_t y,unsigned int num,uint8_t len,uint8_t size2, Color_Turn)
 * @description: 显示数字
 * @param {uint8_t} x待显示的数字起始横坐标,x:0~126
 * @param {uint8_t} y待显示的数字起始纵坐标, y:0~7,若选择字体大小为16,则两行数字之间需要间隔2,若选择字体大小为12,间隔1
 * @param {unsigned int} num:输入的数据
 * @param {uint8_t } len:输入的数据位数
 * @param {uint8_t} size2:输入的数据大小,选择 16/12,16为8X16,12为6x8
 * @param {uint8_t} Color_Turn是否反相显示(1反相、0不反相)
 * @return {*}
 */
void OLED_ShowNum(uint8_t x,uint8_t y,unsigned int num,uint8_t len,uint8_t size2, uint8_t Color_Turn)
{
	uint8_t t,temp;
	uint8_t enshow=0;
	for(t=0;t<len;t++)
	{
		temp=(num/oled_pow(10,len-t-1))%10;
		if(enshow==0&&t<(len-1))
		{
			if(temp==0)
			{
				OLED_ShowChar(x+(size2/2)*t,y,' ',size2, Color_Turn);
				continue;
			}else enshow=1;

		}
	 	OLED_ShowChar(x+(size2/2)*t,y,temp+'0',size2, Color_Turn);
	}
}


/**
 * @function: void OLED_Showdecimal(uint8_t x,uint8_t y,float num,uint8_t z_len,uint8_t f_len,uint8_t size2, uint8_t Color_Turn)
 * @description: 显示正负浮点数
 * @param {uint8_t} x待显示的数字起始横坐标,x:0~126
 * @param {uint8_t} y待显示的数字起始纵坐标, y:0~7,若选择字体大小为16,则两行数字之间需要间隔2,若选择字体大小为12,间隔1
 * @param {float} num:输入的浮点型数据
 * @param {uint8_t } z_ len:整数部分的位数
 * @param {uint8_t } f_len: 小数部分的位数
 * @param {uint8_t} size2:输入的数据大小,选择 16/12,16为8X16,12为6x8
 * @param {uint8_t} Color_Turn是否反相显示(1反相、0不反相)
 * @return {*}
 */
void OLED_Showdecimal(uint8_t x,uint8_t y,float num,uint8_t z_len,uint8_t f_len,uint8_t size2, uint8_t Color_Turn)
{
	uint8_t t,temp,i=0;//i为负数标志位
	uint8_t enshow;
	int z_temp,f_temp;
	if(num<0)
	{
		z_len+=1;
		i=1;
		num=-num;
	}
	z_temp=(int)num;
	//整数部分
	for(t=0;t<z_len;t++)
	{
		temp=(z_temp/oled_pow(10,z_len-t-1))%10;
		if(enshow==0 && t<(z_len-1))
		{
			if(temp==0)
			{
				OLED_ShowChar(x+(size2/2)*t,y,' ',size2, Color_Turn);
				continue;
			}
			else
			enshow=1;
		}
		OLED_ShowChar(x+(size2/2)*t,y,temp+'0',size2, Color_Turn);
	}
	//小数点
	OLED_ShowChar(x+(size2/2)*(z_len),y,'.',size2, Color_Turn);

	f_temp=(int)((num-z_temp)*(oled_pow(10,f_len)));
  //小数部分
	for(t=0;t<f_len;t++)
	{
		temp=(f_temp/oled_pow(10,f_len-t-1))%10;
		OLED_ShowChar(x+(size2/2)*(t+z_len)+5,y,temp+'0',size2, Color_Turn);
	}
	if(i==1)//如果为负,就将最前的一位赋值‘-’
	{
		OLED_ShowChar(x,y,'-',size2, Color_Turn);
		i=0;
	}
}



/**
 * @function: void OLED_ShowCHinese(uint8_t x,uint8_t y,uint8_t no, uint8_t Color_Turn)
 * @description: 在OLED特定位置开始显示16X16汉字
 * @param {uint8_t} x待显示的汉字起始横坐标x: 0~112,两列汉字之间需要间隔16
 * @param {uint8_t} y待显示的汉字起始纵坐标 y: 0~6 , 两行汉字之间需要间隔2
 * @param {uint8_t} no待显示的汉字编号
 * @param {uint8_t} Color_Turn是否反相显示(1反相、0不反相)
 * @return {*}
 */
void OLED_ShowCHinese(uint8_t x,uint8_t y,uint8_t no, uint8_t Color_Turn)
{
	uint8_t t=0;
	OLED_Set_Pos(x,y);
    for(t=0;t<16;t++)
		{
				if (Color_Turn)
					OLED_WR_DATA(~Hzk[2*no][t]); //显示汉字的上半部分
				else
					OLED_WR_DATA(Hzk[2*no][t]); //显示汉字的上半部分
        }

		OLED_Set_Pos(x,y+1);
    for(t=0;t<16;t++)
		{
				if (Color_Turn)
					OLED_WR_DATA(~Hzk[2*no+1][t]); //显示汉字的上半部分
				else
					OLED_WR_DATA(Hzk[2*no+1][t]);//显示汉字的上半部分

         }
}

/**
 * @function: void OLED_DrawBMP(uint8_t x0, uint8_t y0, uint8_t x1, uint8_t y1, uint8_t *  BMP,uint8_t Color_Turn)
 * @description: 在OLED特定区域显示BMP图片
 * @param {uint8_t} x0图像开始显示横坐标  x0:0~127
 * @param {uint8_t} y0图像开始显示纵坐标  y0:0~7
 * @param {uint8_t} x1图像结束显示横坐标  x1:1~128
 * @param {uint8_t} y1图像结束显示纵坐标  y1:1~8
 * @param {uint8_t} *BMP待显示的图像数据
 * @param {uint8_t} Color_Turn是否反相显示(1反相、0不反相)
 * @return {*}
 */
void OLED_DrawBMP(uint8_t x0, uint8_t y0, uint8_t x1, uint8_t y1, uint8_t *  BMP,uint8_t Color_Turn)
{
   uint32_t j = 0;
   uint8_t x = 0, y = 0;

  if(y1%8==0)
		y = y1/8;
  else
		y = y1/8 + 1;
	for(y=y0;y<y1;y++)
	{
		OLED_Set_Pos(x0,y);
    for(x=x0;x<x1;x++)
		{
			if (Color_Turn)
				OLED_WR_DATA(~BMP[j++]);//显示反相图片
			else
				OLED_WR_DATA(BMP[j++]);//显示图片

		}
	}
}

/*
	@brief			显示动图
	@param			x0:起始列地址
				y0:起始页地址
				x1:终止列地址
				y1:终止页地址
				k: 帧个数
				m: 单帧数组大小
				BMP[][m]:存放动图代码的数组
	@retval			无
 */
void OLED_DrawGIF(uint8_t x0, uint8_t  y0, uint8_t  x1, uint8_t y1, uint8_t  k, int m, unsigned char GIF[][m])
{
	unsigned int j=0; //定义变量
 	unsigned char x,y,i; //定义变量
  
 	if(y1%8==0) y=y1/8;   //判断终止页是否为8的整数倍
 	 else y=y1/8+1;
	for (i=0;i<k;i++) //从第一帧开始画
	{
		j = 0;
		for(y=y0;y<y1;y++) //从起始页开始,画到终止页
		{
			OLED_Set_Pos(x0,y);//在页的起始列开始画
			
			for(x=x0;x<x1;x++) //画x1 - x0 列
	    		{
						OLED_WR_DATA(GIF[i][j++]);		//画图片的点  
	    		}
		}
		//delay_ms(80);//人为制造卡顿???

	}
}



/**
 * @function: void OLED_HorizontalShift(uint8_t direction)
 * @description: 屏幕内容水平全屏滚动播放
 * @param {uint8_t} direction			LEFT	   0x27     	RIGHT  0x26
 * @return {*}
 */
void OLED_HorizontalShift(uint8_t direction)

{
	OLED_WR_CMD(0x2e);//停止滚动
	OLED_WR_CMD(direction);//设置滚动方向
	OLED_WR_CMD(0x00);//虚拟字节设置,默认为0x00
	OLED_WR_CMD(0x00);//设置开始页地址
	OLED_WR_CMD(0x07);//设置每个滚动步骤之间的时间间隔的帧频
    //  0x00-5帧, 0x01-64帧, 0x02-128帧, 0x03-256帧, 0x04-3帧, 0x05-4帧, 0x06-25帧, 0x07-2帧,
	OLED_WR_CMD(0x07);//设置结束页地址
	OLED_WR_CMD(0x00);//虚拟字节设置,默认为0x00
	OLED_WR_CMD(0xff);//虚拟字节设置,默认为0xff
	OLED_WR_CMD(0x2f);//开启滚动-0x2f,禁用滚动-0x2e,禁用需要重写数据
}

/**
 * @function: void OLED_Some_HorizontalShift(uint8_t direction,uint8_t start,uint8_t end)
 * @description: 屏幕部分内容水平滚动播放
 * @param {uint8_t} direction			LEFT	   0x27     	RIGHT  0x26
 * @param {uint8_t} start 开始页地址  0x00~0x07
 * @param {uint8_t} end  结束页地址  0x01~0x07
 * @return {*}
 */
void OLED_Some_HorizontalShift(uint8_t direction,uint8_t start,uint8_t end)
{
	OLED_WR_CMD(0x2e);//停止滚动
	OLED_WR_CMD(direction);//设置滚动方向
	OLED_WR_CMD(0x00);//虚拟字节设置,默认为0x00
	OLED_WR_CMD(start);//设置开始页地址
	OLED_WR_CMD(0x07);//设置每个滚动步骤之间的时间间隔的帧频,0x07即滚动速度2帧
	OLED_WR_CMD(end);//设置结束页地址
	OLED_WR_CMD(0x00);//虚拟字节设置,默认为0x00
	OLED_WR_CMD(0xff);//虚拟字节设置,默认为0xff
	OLED_WR_CMD(0x2f);//开启滚动-0x2f,禁用滚动-0x2e,禁用需要重写数据

}

/**
 * @function: void OLED_VerticalAndHorizontalShift(uint8_t direction)
 * @description: 屏幕内容垂直水平全屏滚动播放
 * @param {uint8_t} direction				右上滚动	 0x29
 *                                                            左上滚动   0x2A
 * @return {*}
 */
void OLED_VerticalAndHorizontalShift(uint8_t direction)
{
	OLED_WR_CMD(0x2e);//停止滚动
	OLED_WR_CMD(direction);//设置滚动方向
	OLED_WR_CMD(0x01);//虚拟字节设置
	OLED_WR_CMD(0x00);//设置开始页地址
	OLED_WR_CMD(0x07);//设置每个滚动步骤之间的时间间隔的帧频,即滚动速度
	OLED_WR_CMD(0x07);//设置结束页地址
	OLED_WR_CMD(0x01);//垂直滚动偏移量
	OLED_WR_CMD(0x00);//虚拟字节设置,默认为0x00
	OLED_WR_CMD(0xff);//虚拟字节设置,默认为0xff
	OLED_WR_CMD(0x2f);//开启滚动-0x2f,禁用滚动-0x2e,禁用需要重写数据
}

/**
 * @function: void OLED_DisplayMode(uint8_t mode)
 * @description: 屏幕内容取反显示
 * @param {uint8_t} direction			ON	0xA7  ,
 *                                                          OFF	0xA6	默认此模式,设置像素点亮
 * @return {*}
 */
void OLED_DisplayMode(uint8_t mode)
{
	OLED_WR_CMD(mode);
}

/**
 * @function: void OLED_IntensityControl(uint8_t intensity)
 * @description: 屏幕亮度调节
 * @param  {uint8_t} intensity	0x00~0xFF,RESET=0x7F
 * @return {*}
 */
void OLED_IntensityControl(uint8_t intensity)
{
	OLED_WR_CMD(0x81);
	OLED_WR_CMD(intensity);
}



3.2.  oled.h

/*
 * oled.h
 *
 *  Created on: 2022年9月30日
 *      Author: Unicorn_Yihao
 */

#ifndef __OLED_H__
#define __OLED_H__

#include "main.h"
#include "oledfont.h"

extern SPI_HandleTypeDef  hspi1;

#define OLED_RES_Clr() HAL_GPIO_WritePin(OLED_RES_GPIO_Port,OLED_RES_Pin,GPIO_PIN_RESET)//RES
#define OLED_RES_Set() HAL_GPIO_WritePin(OLED_RES_GPIO_Port,OLED_RES_Pin,GPIO_PIN_SET)

#define OLED_DC_Clr() HAL_GPIO_WritePin(OLED_DC_GPIO_Port,OLED_DC_Pin,GPIO_PIN_RESET)//DC
#define OLED_DC_Set() HAL_GPIO_WritePin(OLED_DC_GPIO_Port,OLED_DC_Pin,GPIO_PIN_SET)
 		     
#define OLED_CS_Clr()  HAL_GPIO_WritePin(OLED_CS_GPIO_Port,OLED_CS_Pin,GPIO_PIN_RESET)//CS
#define OLED_CS_Set()  HAL_GPIO_WritePin(OLED_CS_GPIO_Port,OLED_CS_Pin,GPIO_PIN_SET)


void OLED_WR_CMD(uint8_t cmd);
void OLED_WR_DATA(uint8_t data);
void OLED_Init(void);
void OLED_Clear(void);
void OLED_Display_On(void);
void OLED_Display_Off(void);
void OLED_Set_Pos(uint8_t x, uint8_t y);
void OLED_On(void);
void OLED_ShowNum(uint8_t x,uint8_t y,unsigned int num,uint8_t len,uint8_t size2,uint8_t Color_Turn);
void OLED_Showdecimal(uint8_t x,uint8_t y,float num,uint8_t z_len,uint8_t f_len,uint8_t size2, uint8_t Color_Turn);
void OLED_ShowChar(uint8_t x,uint8_t y,uint8_t chr,uint8_t Char_Size,uint8_t Color_Turn);
void OLED_ShowString(uint8_t x,uint8_t y,char*chr,uint8_t Char_Size,uint8_t Color_Turn);
void OLED_ShowCHinese(uint8_t x,uint8_t y,uint8_t no,uint8_t Color_Turn);
void OLED_DrawBMP(uint8_t x0, uint8_t y0, uint8_t x1, uint8_t y1, uint8_t *  BMP,uint8_t Color_Turn);
void OLED_DrawGIF(uint8_t x0, uint8_t  y0, uint8_t  x1, uint8_t y1, uint8_t  k, int m, unsigned char GIF[][m]);
void OLED_HorizontalShift(uint8_t direction);
void OLED_Some_HorizontalShift(uint8_t direction,uint8_t start,uint8_t end);
void OLED_VerticalAndHorizontalShift(uint8_t direction);
void OLED_DisplayMode(uint8_t mode);
void OLED_IntensityControl(uint8_t intensity);

void OLED_DrawDot(uint8_t x,uint8_t y);
void OLED_Draw_XLine(uint8_t x,uint8_t y,int length);
void OLED_Draw_YLine(uint8_t x,uint8_t y,int length);


#endif 

3.3.  oledfont.c

/*
 * oledfont.c
 *
 *  Created on: Jul 24, 2022
 *      Author: Unicorn_Yihao
 */
#include "oledfont.h"

//8*6 ASCII字符集点阵
const unsigned char F6x8[][6] =
{
	0x00, 0x00, 0x00, 0x00, 0x00, 0x00,// sp
	0x00, 0x00, 0x00, 0x2f, 0x00, 0x00,// !
	0x00, 0x00, 0x07, 0x00, 0x07, 0x00,// "
	0x00, 0x14, 0x7f, 0x14, 0x7f, 0x14,// #
	0x00, 0x24, 0x2a, 0x7f, 0x2a, 0x12,// $
	0x00, 0x62, 0x64, 0x08, 0x13, 0x23,// %
	0x00, 0x36, 0x49, 0x55, 0x22, 0x50,// &
	0x00, 0x00, 0x05, 0x03, 0x00, 0x00,// '
	0x00, 0x00, 0x1c, 0x22, 0x41, 0x00,// (
	0x00, 0x00, 0x41, 0x22, 0x1c, 0x00,// )
	0x00, 0x14, 0x08, 0x3E, 0x08, 0x14,// *
	0x00, 0x08, 0x08, 0x3E, 0x08, 0x08,// +
	0x00, 0x00, 0x00, 0xA0, 0x60, 0x00,// ,
	0x00, 0x08, 0x08, 0x08, 0x08, 0x08,// -
	0x00, 0x00, 0x60, 0x60, 0x00, 0x00,// .
	0x00, 0x20, 0x10, 0x08, 0x04, 0x02,// /
	0x00, 0x3E, 0x51, 0x49, 0x45, 0x3E,// 0
	0x00, 0x00, 0x42, 0x7F, 0x40, 0x00,// 1
	0x00, 0x42, 0x61, 0x51, 0x49, 0x46,// 2
	0x00, 0x21, 0x41, 0x45, 0x4B, 0x31,// 3
	0x00, 0x18, 0x14, 0x12, 0x7F, 0x10,// 4
	0x00, 0x27, 0x45, 0x45, 0x45, 0x39,// 5
	0x00, 0x3C, 0x4A, 0x49, 0x49, 0x30,// 6
	0x00, 0x01, 0x71, 0x09, 0x05, 0x03,// 7
	0x00, 0x36, 0x49, 0x49, 0x49, 0x36,// 8
	0x00, 0x06, 0x49, 0x49, 0x29, 0x1E,// 9
	0x00, 0x00, 0x36, 0x36, 0x00, 0x00,// :
	0x00, 0x00, 0x56, 0x36, 0x00, 0x00,// ;
	0x00, 0x08, 0x14, 0x22, 0x41, 0x00,// <
	0x00, 0x14, 0x14, 0x14, 0x14, 0x14,// =
	0x00, 0x00, 0x41, 0x22, 0x14, 0x08,// >
	0x00, 0x02, 0x01, 0x51, 0x09, 0x06,// ?
	0x00, 0x32, 0x49, 0x59, 0x51, 0x3E,// @
	0x00, 0x7C, 0x12, 0x11, 0x12, 0x7C,// A
	0x00, 0x7F, 0x49, 0x49, 0x49, 0x36,// B
	0x00, 0x3E, 0x41, 0x41, 0x41, 0x22,// C
	0x00, 0x7F, 0x41, 0x41, 0x22, 0x1C,// D
	0x00, 0x7F, 0x49, 0x49, 0x49, 0x41,// E
	0x00, 0x7F, 0x09, 0x09, 0x09, 0x01,// F
	0x00, 0x3E, 0x41, 0x49, 0x49, 0x7A,// G
	0x00, 0x7F, 0x08, 0x08, 0x08, 0x7F,// H
	0x00, 0x00, 0x41, 0x7F, 0x41, 0x00,// I
	0x00, 0x20, 0x40, 0x41, 0x3F, 0x01,// J
	0x00, 0x7F, 0x08, 0x14, 0x22, 0x41,// K
	0x00, 0x7F, 0x40, 0x40, 0x40, 0x40,// L
	0x00, 0x7F, 0x02, 0x0C, 0x02, 0x7F,// M
	0x00, 0x7F, 0x04, 0x08, 0x10, 0x7F,// N
	0x00, 0x3E, 0x41, 0x41, 0x41, 0x3E,// O
	0x00, 0x7F, 0x09, 0x09, 0x09, 0x06,// P
	0x00, 0x3E, 0x41, 0x51, 0x21, 0x5E,// Q
	0x00, 0x7F, 0x09, 0x19, 0x29, 0x46,// R
	0x00, 0x46, 0x49, 0x49, 0x49, 0x31,// S
	0x00, 0x01, 0x01, 0x7F, 0x01, 0x01,// T
	0x00, 0x3F, 0x40, 0x40, 0x40, 0x3F,// U
	0x00, 0x1F, 0x20, 0x40, 0x20, 0x1F,// V
	0x00, 0x3F, 0x40, 0x38, 0x40, 0x3F,// W
	0x00, 0x63, 0x14, 0x08, 0x14, 0x63,// X
	0x00, 0x07, 0x08, 0x70, 0x08, 0x07,// Y
	0x00, 0x61, 0x51, 0x49, 0x45, 0x43,// Z
	0x00, 0x00, 0x7F, 0x41, 0x41, 0x00,// [
	0x00, 0x55, 0x2A, 0x55, 0x2A, 0x55,// 55
	0x00, 0x00, 0x41, 0x41, 0x7F, 0x00,// ]
	0x00, 0x04, 0x02, 0x01, 0x02, 0x04,// ^
	0x00, 0x40, 0x40, 0x40, 0x40, 0x40,// _
	0x00, 0x00, 0x01, 0x02, 0x04, 0x00,// '
	0x00, 0x20, 0x54, 0x54, 0x54, 0x78,// a
	0x00, 0x7F, 0x48, 0x44, 0x44, 0x38,// b
	0x00, 0x38, 0x44, 0x44, 0x44, 0x20,// c
	0x00, 0x38, 0x44, 0x44, 0x48, 0x7F,// d
	0x00, 0x38, 0x54, 0x54, 0x54, 0x18,// e
	0x00, 0x08, 0x7E, 0x09, 0x01, 0x02,// f
	0x00, 0x18, 0xA4, 0xA4, 0xA4, 0x7C,// g
	0x00, 0x7F, 0x08, 0x04, 0x04, 0x78,// h
	0x00, 0x00, 0x44, 0x7D, 0x40, 0x00,// i
	0x00, 0x40, 0x80, 0x84, 0x7D, 0x00,// j
	0x00, 0x7F, 0x10, 0x28, 0x44, 0x00,// k
	0x00, 0x00, 0x41, 0x7F, 0x40, 0x00,// l
	0x00, 0x7C, 0x04, 0x18, 0x04, 0x78,// m
	0x00, 0x7C, 0x08, 0x04, 0x04, 0x78,// n
	0x00, 0x38, 0x44, 0x44, 0x44, 0x38,// o
	0x00, 0xFC, 0x24, 0x24, 0x24, 0x18,// p
	0x00, 0x18, 0x24, 0x24, 0x18, 0xFC,// q
	0x00, 0x7C, 0x08, 0x04, 0x04, 0x08,// r
	0x00, 0x48, 0x54, 0x54, 0x54, 0x20,// s
	0x00, 0x04, 0x3F, 0x44, 0x40, 0x20,// t
	0x00, 0x3C, 0x40, 0x40, 0x20, 0x7C,// u
	0x00, 0x1C, 0x20, 0x40, 0x20, 0x1C,// v
	0x00, 0x3C, 0x40, 0x30, 0x40, 0x3C,// w
	0x00, 0x44, 0x28, 0x10, 0x28, 0x44,// x
	0x00, 0x1C, 0xA0, 0xA0, 0xA0, 0x7C,// y
	0x00, 0x44, 0x64, 0x54, 0x4C, 0x44,// z
	0x14, 0x14, 0x14, 0x14, 0x14, 0x14,// horiz lines
};

//16*8 ASCII字符集点阵
const unsigned char F8X16[]=
{
 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//sp /0
 0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00,//!  /1
 0x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//"  /2
 0x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x04,0x00,//#  /3
 0x00,0x70,0x88,0xFC,0x08,0x30,0x00,0x00,0x00,0x18,0x20,0xFF,0x21,0x1E,0x00,0x00,//$  /4
 0xF0,0x08,0xF0,0x00,0xE0,0x18,0x00,0x00,0x00,0x21,0x1C,0x03,0x1E,0x21,0x1E,0x00,//%  /5
 0x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,0x1E,0x21,0x23,0x24,0x19,0x27,0x21,0x10,//&  /6
 0x10,0x16,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//'  /7
 0x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00,//(  /8
 0x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00,//)  /9
 0x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00,//*  /10
 0x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x1F,0x01,0x01,0x01,0x00,//+  /11
 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xB0,0x70,0x00,0x00,0x00,0x00,0x00,//,  /12
 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,//-  /13
 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,//.  /14
 0x00,0x00,0x00,0x00,0x80,0x60,0x18,0x04,0x00,0x60,0x18,0x06,0x01,0x00,0x00,0x00,///  /15
 0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,//0  /16
 0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//1  /17
 0x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00,//2  /18
 0x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00,//3  /19
 0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00,//4  /20
 0x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00,//5  /21
 0x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00,//6  /22
 0x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,//7  /23
 0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00,//8  /24
 0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00,//9  /25
 0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,//:  /26
 0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x60,0x00,0x00,0x00,0x00,//;  /27
 0x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00,//<  /28
 0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00,//=  /29
 0x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00,//>  /30
 0x00,0x70,0x48,0x08,0x08,0x08,0xF0,0x00,0x00,0x00,0x00,0x30,0x36,0x01,0x00,0x00,//?  /31
 0xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,0x07,0x18,0x27,0x24,0x23,0x14,0x0B,0x00,//@  /32
 0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20,//A  /33
 0x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00,//B  /34
 0xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00,//C  /35
 0x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00,//D  /36
 0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00,//E  /37
 0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00,//F  /38
 0xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00,//G  /39
 0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20,//H  /40
 0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//I  /41
 0x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00,//J  /42
 0x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00,//K  /43
 0x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00,//L  /44
 0x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,0x20,0x3F,0x00,0x3F,0x00,0x3F,0x20,0x00,//M  /45
 0x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00,//N  /46
 0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00,//O  /47
 0x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00,//P  /48
 0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x18,0x24,0x24,0x38,0x50,0x4F,0x00,//Q  /49
 0x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20,//R  /50
 0x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00,//S  /51
 0x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//T  /52
 0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//U  /53
 0x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00,//V  /54
 0xF8,0x08,0x00,0xF8,0x00,0x08,0xF8,0x00,0x03,0x3C,0x07,0x00,0x07,0x3C,0x03,0x00,//W  /55
 0x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20,//X  /56
 0x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//Y  /57
 0x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00,//Z  /58
 0x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00,//[  /59
 0x00,0x0C,0x30,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00,//\  /60
 0x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00,//]  /61
 0x00,0x00,0x04,0x02,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//^  /62
 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,//_  /63
 0x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//`  /64
 0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20,//a  /65
 0x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00,//b  /66
 0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00,//c  /67
 0x00,0x00,0x00,0x80,0x80,0x88,0xF8,0x00,0x00,0x0E,0x11,0x20,0x20,0x10,0x3F,0x20,//d  /68
 0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00,//e  /69
 0x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//f  /70
 0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00,//g  /71
 0x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//h  /72
 0x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//i  /73
 0x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,//j  /74
 0x08,0xF8,0x00,0x00,0x80,0x80,0x80,0x00,0x20,0x3F,0x24,0x02,0x2D,0x30,0x20,0x00,//k  /75
 0x00,0x08,0x08,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//l  /76
 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F,//m  /77
 0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//n  /78
 0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//o  /79
 0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,0x80,0xFF,0xA1,0x20,0x20,0x11,0x0E,0x00,//p  /80
 0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x0E,0x11,0x20,0x20,0xA0,0xFF,0x80,//q  /81
 0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00,//r  /82
 0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00,//s  /83
 0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00,//t  /84
 0x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20,//u  /85
 0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x00,0x01,0x0E,0x30,0x08,0x06,0x01,0x00,//v  /86
 0x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00,//w  /87
 0x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x31,0x2E,0x0E,0x31,0x20,0x00,//x  /88
 0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x80,0x81,0x8E,0x70,0x18,0x06,0x01,0x00,//y  /89
 0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00,//z  /90
 0x00,0x00,0x00,0x00,0x80,0x7C,0x02,0x02,0x00,0x00,0x00,0x00,0x00,0x3F,0x40,0x40,//{  /91
 0x00,0x02,0x02,0x7C,0x80,0x00,0x00,0x00,0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x00,//}  /92
 0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00};//|  /93

//部分汉字 阴码,列行式,逆向
const unsigned char Hzk[][32]=
{
		{0x40,0x22,0x14,0x08,0xF4,0x02,0x00,0xF8,0x08,0x08,0xFF,0x08,0x08,0xF8,0x00,0x00},
		{0x08,0x44,0x82,0x41,0x3F,0x00,0x20,0x63,0x21,0x21,0x3F,0x21,0x29,0x33,0x60,0x00},/*"独",0*/
		{0x20,0x10,0xE8,0x24,0x27,0x24,0x24,0xE4,0x24,0x34,0x2C,0x20,0xE0,0x00,0x00,0x00},
		{0x80,0x60,0x1F,0x09,0x09,0x09,0x09,0x7F,0x09,0x09,0x49,0x89,0x7F,0x00,0x00,0x00},/*"角",1*/
		{0x00,0x00,0x7C,0x54,0x55,0x56,0x54,0x7C,0x54,0x56,0x55,0x54,0x7C,0x00,0x00,0x00},
		{0x01,0x01,0x01,0xFD,0x45,0x45,0x45,0x45,0x45,0x45,0x45,0xFD,0x01,0x01,0x01,0x00},/*"兽",2*/



};
//128*64图片
unsigned char BMP1[]={
		0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x00,0x40,0xE0,0xE0,0x60,
		0x00,0x40,0x80,0x00,0x00,0x00,0x80,0x80,0x60,0x60,0x10,0x00,0x00,0x00,0x00,0x00,
		0x00,0x00,0x00,0x00,0x00,0x90,0xB2,0x66,0x6E,0xEC,0xC9,0x83,0x02,0x00,0x40,0x80,
		0x00,0x0C,0x0C,0x01,0x03,0x07,0x0F,0x11,0x20,0x40,0x80,0x00,0x00,0x00,0x00,0x00,
		0x00,0x00,0x00,0x00,0x08,0x18,0x3B,0x37,0x66,0xEE,0xEE,0xCC,0x88,0x80,0x00,0x00,
		0x01,0x02,0x04,0x08,0x10,0x10,0x10,0x10,0x10,0x10,0x0F,0x00,0x00,0x00,0x00,0x00,
		0x00,0x3E,0x40,0x40,0x40,0x3E,0x00,0x7E,0x04,0x08,0x10,0x7E,0x00,0x7E,0x00,0x3C,
		0x42,0x42,0x42,0x42,0x00,0x7E,0x42,0x42,0x42,0x7E,0x00,0x7E,0x04,0x08,0x10,0x7E,/*"C:\Users\HP\Desktop\UNICORN.BMP",0*/


};


3.4.  oledfont.h

/*
 * oledfont.h
 *
 *  Created on: 2022年7月24日
 *      Author: Unicorn_Yihao
 */

#ifndef __OLEDFONT_H__
#define __OLEDFONT_H__

extern const unsigned char F6x8[][6];
extern const unsigned char F8X16[];
extern const unsigned char Hzk[][32];
extern unsigned char BMP1[];

#endif /* OLED_OLEDFONT_H_ */

3.5. main.h

/* Private defines -----------------------------------------------------------*/

#define OLED_RES_Pin        GPIO_PIN_0
#define OLED_RES_GPIO_Port  GPIOB
#define OLED_DC_Pin         GPIO_PIN_1
#define OLED_DC_GPIO_Port   GPIOB
#define OLED_CS_Pin         GPIO_PIN_10
#define OLED_CS_GPIO_Port   GPIOB

3.6. main.c (仅测试使用)

/* USER CODE BEGIN Includes */
#include "oled.h"
/* USER CODE END Includes */
/* USER CODE BEGIN 2 */
 OLED_Init();                           //OLED初始
 OLED_Clear();                         //清屏
//上面的初始化以及清屏的代码在一开始处一定要写
 OLED_ShowString(0,0,"UNICORN_LI",16, 1);    //反相显示8X16字符串
 OLED_ShowString(0,2,"unicorn_li_123",12,0);//正相显示6X8字符串
 
 OLED_ShowCHinese(0,4,0,1); //反相显示汉字“独”
 OLED_ShowCHinese(16,4,1,1);//反相显示汉字“角”
 OLED_ShowCHinese(32,4,2,1);//反相显示汉字“兽”
 OLED_ShowCHinese(0,6,0,0); //正相显示汉字“独”
 OLED_ShowCHinese(16,6,1,0);//正相显示汉字“角”
 OLED_ShowCHinese(32,6,2,0);//正相显示汉字“兽”

 OLED_ShowNum(48,4,6,1,16, 0);//正相显示1位8X16数字“6”
 OLED_ShowNum(48,7,77,2,12, 1);//反相显示2位6X8数字“77”
 OLED_DrawBMP(90,0,122, 4,BMP1,0);//正相显示图片BMP1
 OLED_DrawBMP(90,4,122, 8,BMP1,1);//反相显示图片BMP1
 
 OLED_HorizontalShift(0x26);//全屏水平向右滚动播放

//显示正负浮点数的代码
//  float num1=-231.24;
//  float num2=23.375;

//OLED_ShowString(0,0,"Show Decimal",12,0);
//OLED_Showdecimal(0,4,num1,3,2,12, 0);
//OLED_Showdecimal(0,6,num2,2,3,16, 1);

 
  /* USER CODE END 2 */

四、推荐学习

SSD1306驱动指令https://blog.csdn.net/qq_39829913/article/details/104716829


总结

以上就是7针0.96寸OLED的HAL库版本的代码,全部按我这个操作100%一次点亮OLED屏,接下来我还会分享 软件I2C、软件SPI以及简易OLED多级菜单。

点点关注不迷路


这篇文章主要分享以及记录学习中的感悟,可能还有不足,还望大佬们在评论区提出,大家相互学习与进步。


欢迎大家积极交流,本文未经允许谢绝转载!!!文章来源地址https://www.toymoban.com/news/detail-599153.html

到了这里,关于7针0.96寸OLED的HAL库代码(硬件SPI/全代码/stm32f1/CubeMX配置/包含有正负浮点数/100%一次点亮)的文章就介绍完了。如果您还想了解更多内容,请在右上角搜索TOY模板网以前的文章或继续浏览下面的相关文章,希望大家以后多多支持TOY模板网!

本文来自互联网用户投稿,该文观点仅代表作者本人,不代表本站立场。本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如若转载,请注明出处: 如若内容造成侵权/违法违规/事实不符,请点击违法举报进行投诉反馈,一经查实,立即删除!

领支付宝红包 赞助服务器费用

相关文章

  • STM32F103硬件SPI控制6针/7针0.96寸OLED显示屏

    OLED主要参数 1、高分辨率:128 64(和12864LCD相同分辨率,但该OLED屏的单位面积像素点多)。 2、广可视角度:大于160°。 3、低功耗:正常显示时0.04W。 4、宽供电范围:直流3.3V-5V。 5、工业级:工作温度范围-30°℃~70°℃。 6、体积小:28.8mm 28.5mm。 7、通信方式:lIC、SPI。 8、亮

    2024年02月17日
    浏览(80)
  • 一个简单的HAL库STM32使用DMA+硬件IIC驱动0.96寸OLED的方法

    自己在刚入坑嵌入式的时候,加入学校科协的一道免试题是开发一个简易的示波器,当时萌新不会做,中间又在准备比赛没时间,最近帮女朋友做课设需要做一个简易的交流电压表,而且终于有空做一下自己感兴趣的项目了,就想到了之前想做有没得做的一个简易示波器。

    2024年02月19日
    浏览(42)
  • 0.96OLED STM32 SPI驱动(一)

    闲来无聊,翻出了一个OLED,本来想串流做个小显示器用,感觉难度太大。将就变成了下面这 个样子,姑且叫火柴人大乱斗之OLED。 火柴人之OLED 分两步走,先驱动OLED能显示一副图片,本篇讲述此内容。 第二步显示动画,放在下一篇中讲。 查资料得到此OLED为SPI通信,SCL对应连

    2024年02月06日
    浏览(53)
  • STM32--7针0.96寸OLED屏幕显示(4线SPI)

    本文介绍基于STM32F103C8T6+0.96寸OLED(7针)的显示(完整程序代码见文末链接) 一、简介 OLED,即有机发光二极管( Organic Light Emitting Diode)。 OLED 由于同时具备自发光,不需背光源、对比度高、厚度薄、视角广、反应速度快、可用于挠曲性面板、使用温度范围广、构造及制程较

    2024年01月16日
    浏览(49)
  • 0.96OLED 4针IIC STM32-HAL库版本(附源码)

    OLED源码放在文章末,有需要自己下滑取用即可。关于如何移植到自己定义的引脚上也做了说明。 另外,本人在代码中封装了一个OLED显示的接口,方便开发者对字符显示位置的快速定位,以及像C语言printf()函数一样在屏幕上进行int,float,char等变量的格式化输出。非常方便实用

    2023年04月26日
    浏览(101)
  • 【STM32CubeMX】教程二_IIC驱动0.96oled屏幕(SSD1306)

    本篇博客涉及以下内容 IIC通讯原理讲解、代码编写 SSD1306驱动芯片datasheet讲解、驱动代码编写、0.96oled模块原理图说明 STM32CubeMX配置IIC 使用硬件:STM32F103C8T6 使用软件:STM32CubeMX、keil5(MDK)、VSCode(搭载keil assistant插件) 提示:以下是本篇文章正文内容   在计算机科学里,大

    2023年04月21日
    浏览(49)
  • STM32F103模拟SPI控制6针/7针0.96寸OLED显示屏

    OLED主要参数 1、高分辨率:128 64(和12864LCD相同分辨率,但该OLED屏的单位面积像素点多)。 2、广可视角度:大于160°。 3、低功耗:正常显示时0.04W。 4、宽供电范围:直流3.3V-5V。 5、工业级:工作温度范围-30°℃~70°℃。 6、体积小:28.8mm 28.5mm。 7、通信方式:lIC、SPI。 8、亮

    2024年02月04日
    浏览(159)
  • 【STM32】 硬件IIC 驱动SSD1306(0.96 OLED模块) -- 1/4 库函数 学习

    经过了对于STM32的学习,但是大多数时候都还是以移植别人的历程然后修修改改为主。为了更好的巩固自己的学习能力。 所以此篇文章将会以记录我个人学习 硬件IIC 为案例,学习驱动IIC总线设备的能力。 1.《STM32F10x-中文参考手册》 2.《SSD1306芯片手册》 《STM32F10x-中文参考手

    2024年02月01日
    浏览(44)
  • STM32F103硬件IIC控制4针0.96寸OLED显示屏

    OLED使用的0.96寸四针屏幕,以下直接看实际操作。 使用PCtoLCD2002软件提取OLED字模。 注意红色方框的选项内容,不要选错了,选错会导致烧录程序后无法显示。 此为硬件IIC,如果使用过我的模拟IIC控制程序可直接看 void OLED_Write_Command(unsigned char IIC_Command); void OLED_Write_Data(unsig

    2024年02月02日
    浏览(51)
  • 基于HAL库的stm32的OLED显示屏显示(模拟I2C,四脚,0.96寸)

    参考视频:江科大oled程序移植stm32hal库,freertos学习,cpu使用率_哔哩哔哩_bilibili ​ STM32入门教程-2023持续更新中_哔哩哔哩_bilibili 高速和低速晶振均选择为陶瓷晶振即可。 不需更改初始化配置,因为模拟I2C初始化时会设置这两个引脚的电平 step1、step2完成后生成工程即可。 代

    2024年02月06日
    浏览(52)

觉得文章有用就打赏一下文章作者

支付宝扫一扫打赏

博客赞助

微信扫一扫打赏

请作者喝杯咖啡吧~博客赞助

支付宝扫一扫领取红包,优惠每天领

二维码1

领取红包

二维码2

领红包