思科路由器交换机密码破解教程-Toy模板网

这篇具有很好参考价值的文章主要介绍了思科路由器交换机密码破解教程。希望对大家有所帮助。如果存在错误或未考虑完全的地方，请大家不吝赐教，您也可以点击"举报违法"按钮提交疑问。

1. 路由器密码的恢复.

2600、3600等新系列路由器步骤：

1、启动路由器，60秒内按下ctrl+break键2、rommon>confreg 0x21423、rommon>reset4、router#copy startup-config running-config5、router(config)#no enable secrect  //可以删除密码也可以更改,这里为删除6、router(config)#no enable password7、router(config)#config-register 0x21028、router#copy  running-config  startup9、router#reload

2500系列路由器步骤：

1、启动路由器，60秒内按下ctrl+break键2、>o/r 0x21423、>i其余步骤跟2600、3600一样

2．交换机密码恢复

以2950为例

重启交换机：按MODE键进入到switch:模式如下

C2950 Boot Loader (C2950-HBOOT-M) Version 12.1(11r)EA1, RELEASE SOFTWARE (fc1)Compiled Mon 22-Jul-02 17:18 by antoninoWS-C2950-24 starting...Base ethernet MAC Address: 00:13:1a:9a:2b:80Xmodem file system is available.

The system has been interrupted prior to initializing theflash filesystem.  The following commands will initializethe flash filesystem, and finish loading the operatingsystem software:

    flash_init    load_helper    boot

switch: flash_initInitializing Flash...flashfs[0]: 4 files, 1 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 7741440flashfs[0]: Bytes used: 3090944flashfs[0]: Bytes available: 4650496flashfs[0]: flashfs fsck took 6 seconds....done initializing flash.Boot Sector Filesystem (bs:) installed, fsid: 3Parameter Block Filesystem (pb:) installed, fsid: 4switch: load_helperswitch: dir

List of filesystems currently registered:

               flash[0]: (read-write)              xmodem[1]: (read-only)                null[2]: (read-write)                  bs[3]: (read-only)

switch: dir flash:Directory of flash:/

2    -rwx  736       <date>               vlan.dat3    -rwx  3086336   <date>               c2950-i6q4l2-mz.121-22.EA2.bin5    -rwx  1558      <date>               config.text／／交换机启动时应用的配置6    -rwx  5         <date>               private-config.text

4650496 bytes available (3090944 bytes used)switch: rename flash:config.text flash:config-old.txt //重命名config.text switch: reset   //重起交换机Are you sure you want to reset the system (y/n)?ySystem resetting...

重起交换机后由于交换机不会再应用配置文件，因为刚才已把配置文件的名字更改。交换机会进入到配置的对话模式。如查

 --- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: nSwitch#dirDirectory of flash:/
    2  -rwx         736  Mar 01 1993 00:19:14 +00:00  vlan.dat    3  -rwx     3086336  Jan 01 1970 01:12:26 +00:00  c2950-i6q4l2-mz.121-22.EA2.bin    5  -rwx        1558  Mar 01 1993 02:36:44 +00:00  config-old.txt    6  -rwx           5  Mar 01 1993 02:36:44 +00:00  private-config.text
7741440 bytes total (4650496 bytes free)
Switch#copy config-old.txt running-configDestination filename [running-config]?1558 bytes copied in 1.152 secs (1352 bytes/sec)sw#config tEnter configuration commands, one per line.  End with CNTL/Z.sw(config)#line console 0sw(config-line)#no pass cisco ／／清除console口密码sw(config)#no enable secret  ／／清除enable密码sw(config)#no enable password ／／清除enable密码sw#write  //重新保存