HCIP——前期综合实验

这篇具有很好参考价值的文章主要介绍了HCIP——前期综合实验。希望对大家有所帮助。如果存在错误或未考虑完全的地方,请大家不吝赐教,您也可以点击"举报违法"按钮提交疑问。

一、实验拓扑

HCIP——前期综合实验,计算机网络,HCIP,智能路由器,网络,服务器,网络协议,计算机网络,HCIP,华为

二、实验要求

1、该拓扑为公司网络,其中包括公司总部、公司分部以及公司骨干网,不包含运营商公网部分。
2、设备名称均使用拓扑上名称改名,并且区分大小写。
3、整张拓扑均使用私网地址进行配置。
4、整张网络中,运行OSPF协议或者BGP协议的设备,其Router-id值为设备名数字号,例如R1的Router-id为1.1.1.1、
5、OSPF路由宣告部分选择接口宣告方式,例如192.168.100.1 0.0.0.0;BGP仅宣告用户网段。
6、IBGP部分使用环回建立邻居,EBGP部分使用直连链路建立邻居,所有运行BGP的设备都需要建立邻居。
7、R1、R2、R5、R6、R7、R8、R9、R10需要配置环回接口,环回接口IP为设备名数字号,掩码为32,例如R2的环回接口为2.2.2.2/32
8、所有PC的IP地址均手工配置。
公司分部:
1、PC5和PC6属于不同VLAN
3、SW3是一个三层交换机
4、R9是分部出口路由器
5、分部使用OSPF进程200达到分部网络全网可达
6、公司分部出口设备运行BGP协议连接骨干网络,AS号为100
7、因AS-PATH属性原因,总部与分部路由会学习不到,使用命令如(peer 10.10.10.10 allow-as-loop,仅在总部与分部设备上配置即可),将允许AS号重复。
公司总部:
1、交换机为二层交换机
2、PC1和PC2属于一个网段,PC3和PC4是一个网段
3、R3和R4分别是下方PC的网关路由器
4、为保障公司总部到骨干网络的连通性,公司总部使用双路由器双出口的方式接入骨干网
5、为保障公司总部网络内部具备负载,R1、R2、R3、R4设备均作为设备冗余,并使用全连接的方式进行路由选路
6、总部内网使用OSPF进程100达到全网可达,OSPF需要宣告环回。
7、公司总部双出口设备运行BGP协议连接骨干网络,AS号为100
8、因为R1和R2重发布时会出现次优路径,需要修改BGP路由优先级,使用命令(preference 140 255 255,仅在总部设备上配置即可),配置位置在iPv4-family unicast中。
公司骨干网:
1、为保障公司网络连通性,骨干网络考虑设备冗余操作,连接总部使用双路由器,骨干网络部分路由器之间使用双链路路方式
2、骨干网设备运行OSPF协议达到骨干网全网可达,进程号为10。
3、骨干网设备运行BGP协议,AS号为200。使用全连接方式建邻。
优化:
1、为达到分流互备效果,公司总部业务部访问分部流量走R1,R2做备份;公司总部工程部访问分部流量走R2,R1做备份,并要求来回路径一致。
2、公司总部双出口流量均流向R5,R6做备份。来回路径一致。
3、OSPF重发布时,更改类型为Type-1
4、所有策略名称为policy-1
5、更改开销时,全部更改为10
HCIP——前期综合实验,计算机网络,HCIP,智能路由器,网络,服务器,网络协议,计算机网络,HCIP,华为
HCIP——前期综合实验,计算机网络,HCIP,智能路由器,网络,服务器,网络协议,计算机网络,HCIP,华为

三、实验思路

HCIP——前期综合实验,计算机网络,HCIP,智能路由器,网络,服务器,网络协议,计算机网络,HCIP,华为

四、实验步骤

1、配置接口IP地址

R1:

<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys R1
[R1]user-interface console 0
[R1-ui-console0]idle-timeout 0 0
[R1-ui-console0]int g0/0/0
[R1-GigabitEthernet0/0/0]ip address 192.168.100.9 30
[R1-GigabitEthernet0/0/0]int g0/0/1
[R1-GigabitEthernet0/0/1]ip address 192.168.100.41 30
[R1-GigabitEthernet0/0/1]int g0/0/2
[R1-GigabitEthernet0/0/2]ip address 192.168.100.17 30
[R1-GigabitEthernet0/0/2]int g2/0/0
[R1-GigabitEthernet2/0/0]ip address 10.10.10.1 30
[R1-GigabitEthernet2/0/0]int g3/0/0
[R1-GigabitEthernet3/0/0]ip address 10.10.10.5 30
[R1-GigabitEthernet3/0/0]q
[R1]int l0
[R1-LoopBack0]ip address 1.1.1.1 32
[R1-LoopBack0]q
[R1]

R2:

[Huawei]sys R2
[R2]user-interface console 0
[R2-ui-console0]idle-timeout 0 0
[R2-ui-console0]int g0/0/0
[R2-GigabitEthernet0/0/0]ip address 10.10.10.13 30
[R2-GigabitEthernet0/0/0]int g0/0/1
[R2-GigabitEthernet0/0/1]ip address 10.10.10.9 30
[R2-GigabitEthernet0/0/1]int g0/0/2
[R2-GigabitEthernet0/0/2]ip address 10.10.10.42 30 
[R2-GigabitEthernet0/0/2]int g3/0/0
[R2-GigabitEthernet3/0/0]ip address 192.168.100.6 30
[R2-GigabitEthernet3/0/0]int g4/0/0
[R2-GigabitEthernet4/0/0]ip address 192.168.100.13 30
[R2-GigabitEthernet4/0/0]q
[R2]int l0
[R2-LoopBack0]ip address 2.2.2.2 32
[R2-LoopBack0]q
[R2]

R3:

<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys R3
[R3]user-interface console 0
[R3-ui-console0]idle-timeout 0 0
[R3-ui-console0]quit
[R3]
[R3]int g0/0/0
[R3-GigabitEthernet0/0/0]ip address 192.168.100.10 30
[R3-GigabitEthernet0/0/0]int g0/0/1
[R3-GigabitEthernet0/0/1]ip address 192.168.100.5 30
[R3-GigabitEthernet0/0/1]int g0/0/2
[R3-GigabitEthernet0/0/2]ip address 192.168.100.1 30
[R3-GigabitEthernet0/0/2]int g3/0/0
[R3-GigabitEthernet3/0/0]ip address 192.168.1.254 30
[R3-GigabitEthernet3/0/0]q
[R3]int g3/0/0
[R3-GigabitEthernet3/0/0]ip address 192.168.1.254 24
[R3-GigabitEthernet3/0/0]q
[R3]

R4:

<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys R4
[R4]user-interface console 0
[R4-ui-console0]idle-timeout 0 0
[R4-ui-console0]quit
[R4]int g0/0/0
[R4-GigabitEthernet0/0/0]ip address 192.168.100.14 30
[R4-GigabitEthernet0/0/0]int g0/0/1
[R4-GigabitEthernet0/0/1]ip address 192.168.100.18 30
[R4-GigabitEthernet0/0/1]int g0/0/2
[R4-GigabitEthernet0/0/2]ip address 192.168.100.2 30
[R4-GigabitEthernet0/0/2]int g3/0/0
[R4-GigabitEthernet3/0/0]ip address 192.168.2.254 24
[R4-GigabitEthernet3/0/0]q
[R4]

R5:

<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys R5
[R5]user-interface console 0
[R5-ui-console0]idle-timeout 0 0
[R5-ui-console0]quit
[R5]
[R5]int g0/0/0
[R5-GigabitEthernet0/0/0]ip address 10.10.10.2 30
[R5-GigabitEthernet0/0/0]int g0/0/1
[R5-GigabitEthernet0/0/1]ip address 10.10.10.10 30
[R5-GigabitEthernet0/0/1]int g0/0/2
[R5-GigabitEthernet0/0/2]ip address 10.10.10.21 30
[R5-GigabitEthernet0/0/2]int g2/0/0
[R5-GigabitEthernet2/0/0]ip address 10.10.10.17 30
[R5-GigabitEthernet2/0/0]q
[R5]int l0
[R5-LoopBack0]ip address 5.5.5.5 32
[R5-LoopBack0]q
[R5]

R6:

<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys R6
[R6]user-interface console 0
[R6-ui-console0]idle-timeout 0 0
[R6-ui-console0]quit
[R6]int g0/0/0
[R6-GigabitEthernet0/0/0]ip address 10.10.10.14 30
[R6-GigabitEthernet0/0/0]int g0/0/1
[R6-GigabitEthernet0/0/1]ip address 10.10.10.6 30
[R6-GigabitEthernet0/0/1]int g3/0/0
[R6-GigabitEthernet3/0/0]ip address 10.10.10.18 30
[R6-GigabitEthernet3/0/0]int g0/0/2
[R6-GigabitEthernet0/0/2]ip address 10.10.10.25 30
[R6-GigabitEthernet0/0/2]q
[R6]int l0
[R6-LoopBack0]ip address 6.6.6.6 32
[R6-LoopBack0]q
[R6]

R7:

<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys R7
[R7]user-interface console 0
[R7-ui-console0]idle-timeout 0 0
[R7-ui-console0]quit
[R7]
[R7]int g0/0/0
[R7-GigabitEthernet0/0/0]ip address 10.10.10.22 30 
[R7-GigabitEthernet0/0/0]int g0/0/1
[R7-GigabitEthernet0/0/1]ip address 10.10.10.26 30
[R7-GigabitEthernet0/0/1]int g0/0/2
[R7-GigabitEthernet0/0/2]ip address 10.10.10.33 30
[R7-GigabitEthernet0/0/2]int g4/0/0
[R7-GigabitEthernet4/0/0]ip address 10.10.10.29 30
[R7-GigabitEthernet4/0/0]q
[R7]int l0
[R7-LoopBack0]ip ad	
[R7-LoopBack0]ip address 7.7.7.7 32
[R7-LoopBack0]q
[R7]

R8:

<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys R8
[R8]user-interface console 0
[R8-ui-console0]idle-timeout 0 0
[R8-ui-console0]quit
[R8]int g0/0/0
[R8-GigabitEthernet0/0/0]int g0/0/0
[R8-GigabitEthernet0/0/0]ip address 10.10.10.34 30
[R8-GigabitEthernet0/0/0]int g0/0/1
[R8-GigabitEthernet0/0/1]ip address 10.10.10.30 30
[R8-GigabitEthernet0/0/1]int g0/0/2
[R8-GigabitEthernet0/0/2]ip address 10.10.10.37 30
[R8-GigabitEthernet0/0/2]int l0
[R8-LoopBack0]ip ad	
[R8-LoopBack0]ip address 8.8.8.8 32
[R8-LoopBack0]q

R9:

<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys R9
[R9]user-interface console 0
[R9-ui-console0]idle-timeout 0 0
[R9-ui-console0]quit
[R9]int g0/0/0
[R9-GigabitEthernet0/0/0]int g0/0/1
[R9-GigabitEthernet0/0/1]ip address 192.168.200.2 30
[R9-GigabitEthernet0/0/1]int g0/0/2
[R9-GigabitEthernet0/0/2]ip address 10.10.10.38 30
[R9-GigabitEthernet0/0/2]int l0
[R9-LoopBack0]ip address 9.9.9.9 32
[R9-LoopBack0]q
[R9]

R10:

<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys R10
[R10]user-interface console 0
[R10-ui-console0]idle-timeout 0 0
[R10-ui-console0]quit
[R10-GigabitEthernet0/0/0]int g0/0/1.1
[R10-GigabitEthernet0/0/1.1]ip address 192.168.3.254 24
[R10-GigabitEthernet0/0/1.1]int g0/0/1.2
[R10-GigabitEthernet0/0/1.2]ip address 192.168.4.254 24
[R10-GigabitEthernet0/0/1.2]q
[R10]int g0/0/0
[R10-GigabitEthernet0/0/0]ip ad	
[R10-GigabitEthernet0/0/0]ip address 192.168.200.1 30
[R10-GigabitEthernet0/0/0]q
[R10]

检查接口状态以及配置:
R1:

Interface                         IP Address/Mask      Physical   Protocol  
GigabitEthernet0/0/0              192.168.100.9/30     up         up        
GigabitEthernet0/0/1              192.168.100.41/30    up         up        
GigabitEthernet0/0/2              192.168.100.17/30    up         up        
GigabitEthernet2/0/0              10.10.10.1/30        up         up        
GigabitEthernet3/0/0              10.10.10.5/30        up         up        
GigabitEthernet4/0/0              unassigned           down       down      
LoopBack0                         1.1.1.1/32           up         up(s)     
NULL0                             unassigned           up         up(s) 

R2:

Interface                         IP Address/Mask      Physical   Protocol  
GigabitEthernet0/0/0              10.10.10.13/30       up         up        
GigabitEthernet0/0/1              10.10.10.9/30        up         up        
GigabitEthernet0/0/2              10.10.10.42/30       up         up        
GigabitEthernet3/0/0              192.168.100.6/30     up         up        
GigabitEthernet4/0/0              192.168.100.13/30    up         up        
LoopBack0                         2.2.2.2/32           up         up(s)     
NULL0                             unassigned           up         up(s) 

R3:

Interface                         IP Address/Mask      Physical   Protocol  
GigabitEthernet0/0/0              192.168.100.10/30    up         up        
GigabitEthernet0/0/1              192.168.100.5/30     up         up        
GigabitEthernet0/0/2              192.168.100.1/30     up         up        
GigabitEthernet3/0/0              192.168.1.254/24     up         up        
GigabitEthernet4/0/0              unassigned           down       down      
NULL0                             unassigned           up         up(s)     

R4:

Interface                         IP Address/Mask      Physical   Protocol  
GigabitEthernet0/0/0              192.168.100.14/30    up         up        
GigabitEthernet0/0/1              192.168.100.18/30    up         up        
GigabitEthernet0/0/2              192.168.100.2/30     up         up        
GigabitEthernet3/0/0              192.168.2.254/24     up         up        
GigabitEthernet4/0/0              unassigned           down       down      
NULL0                             unassigned           up         up(s)  

R5:

Interface                         IP Address/Mask      Physical   Protocol  
GigabitEthernet0/0/0              10.10.10.2/30        up         up        
GigabitEthernet0/0/1              10.10.10.10/30       up         up        
GigabitEthernet0/0/2              10.10.10.21/30       up         up        
GigabitEthernet2/0/0              10.10.10.17/30       up         up        
GigabitEthernet3/0/0              unassigned           down       down      
GigabitEthernet4/0/0              unassigned           down       down      
LoopBack0                         5.5.5.5/32           up         up(s)     
NULL0                             unassigned           up         up(s)  

R6:

Interface                         IP Address/Mask      Physical   Protocol  
GigabitEthernet0/0/0              10.10.10.14/30       up         up        
GigabitEthernet0/0/1              10.10.10.6/30        up         up        
GigabitEthernet0/0/2              10.10.10.25/30       up         up        
GigabitEthernet3/0/0              10.10.10.18/30       up         up        
GigabitEthernet4/0/0              unassigned           down       down      
LoopBack0                         6.6.6.6/32           up         up(s)     
NULL0                             unassigned           up         up(s)   

R7:

Interface                         IP Address/Mask      Physical   Protocol  
GigabitEthernet0/0/0              10.10.10.22/30       up         up        
GigabitEthernet0/0/1              10.10.10.26/30       up         up        
GigabitEthernet0/0/2              10.10.10.33/30       up         up        
GigabitEthernet4/0/0              10.10.10.29/30       up         up        
LoopBack0                         7.7.7.7/32           up         up(s)     
NULL0                             unassigned           up         up(s)   

R8:

Interface                         IP Address/Mask      Physical   Protocol  
GigabitEthernet0/0/0              10.10.10.34/30       up         up        
GigabitEthernet0/0/1              10.10.10.30/30       up         up        
GigabitEthernet0/0/2              10.10.10.37/30       up         up        
LoopBack0                         8.8.8.8/32           up         up(s)     
NULL0                             unassigned           up         up(s) 

R9:

Interface                         IP Address/Mask      Physical   Protocol  
GigabitEthernet0/0/0              unassigned           down       down      
GigabitEthernet0/0/1              192.168.200.2/30     up         up        
GigabitEthernet0/0/2              10.10.10.38/30       up         up        
LoopBack0                         9.9.9.9/32           up         up(s)     
NULL0                             unassigned           up         up(s)  

R10:

Interface                         IP Address/Mask      Physical   Protocol  
GigabitEthernet0/0/0              192.168.200.1/30     up         up        
GigabitEthernet0/0/1              unassigned           up         down      
GigabitEthernet0/0/1.1            192.168.3.254/24     up         down      
GigabitEthernet0/0/1.2            192.168.4.254/24     up         down      
GigabitEthernet0/0/2              unassigned           down       down      
NULL0                             unassigned           up         up(s)   

2、交换机配置划分vlan10以及vlan20

LSW3:

[SW3]vlan b	
[SW3]vlan batch 10 20
Info: This operation may take a few seconds. Please wait for a moment...done.
[SW3]int g0/0/1
[SW3-GigabitEthernet0/0/1]port link-type trunk 
[SW3-GigabitEthernet0/0/1]port trunk allow-pass vlan 10 20
[SW3-GigabitEthernet0/0/1]int g0/0/2
[SW3-GigabitEthernet0/0/2]port link-type access 
[SW3-GigabitEthernet0/0/2]port default vlan 10
[SW3-GigabitEthernet0/0/2]int g0/0/3
[SW3-GigabitEthernet0/0/3]port link-type access 
[SW3-GigabitEthernet0/0/3]port default vlan 20
[SW3-GigabitEthernet0/0/3]q
[SW3]

R10:

[R10]int g0/0/1.1
[R10-GigabitEthernet0/0/1.1]dot1q termination vid 10
[R10-GigabitEthernet0/0/2.1]int g0/0/1.2
[R10-GigabitEthernet0/0/1.2]dot1q termination vid 20
[R10]int g0/0/1.1
[R10-GigabitEthernet0/0/1.1]arp broadcast 
[R10-GigabitEthernet0/0/1.1]arp broadcast enable 
[R10-GigabitEthernet0/0/1.1]int g0/0/1.2
[R10-GigabitEthernet0/0/1.2]arp broadcast enable 
[R10-GigabitEthernet0/0/1.2]q
[R10]

结果测试:
HCIP——前期综合实验,计算机网络,HCIP,智能路由器,网络,服务器,网络协议,计算机网络,HCIP,华为

3、总部分部,骨干网配置OSPF

分部

R9:

[R9]ospf 200 router-id 9.9.9.9
[R9-ospf-200]area 0
[R9-ospf-200-area-0.0.0.0]network 192.168.200.2 0.0.0.0
[R9-ospf-200-area-0.0.0.0]q
[R9-ospf-200]q
[R9]

R10:

[R10]ospf 200 router-id 10.10.10.10
[R10-ospf-200]area 0
[R10-ospf-200-area-0.0.0.0]network 192.168.200.1 0.0.0.0
[R10-ospf-200-area-0.0.0.0]network 192.168.3.254 0.0.0.0
[R10-ospf-200-area-0.0.0.0]network 192.168.4.254 0.0.0.0
[R10-ospf-200-area-0.0.0.0]q
[R10-ospf-200]q
[R10]

测试:
HCIP——前期综合实验,计算机网络,HCIP,智能路由器,网络,服务器,网络协议,计算机网络,HCIP,华为
查看OSPF路由表:
R9:

[R9]display ip routing-table protocol ospf 
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Public routing table : OSPF
         Destinations : 2        Routes : 2        
OSPF routing table status : <Active>
         Destinations : 2        Routes : 2
Destination/Mask    Proto   Pre  Cost      Flags NextHop         Interface
    192.168.3.0/24  OSPF    10   2           D   192.168.200.1   GigabitEthernet
0/0/1
    192.168.4.0/24  OSPF    10   2           D   192.168.200.1   GigabitEthernet
0/0/1
OSPF routing table status : <Inactive>
         Destinations : 0        Routes : 0
[R9]

总部

R1:

[R1]OSPF 100 router-id 1.1.1.1
[R1-ospf-100]area 0
[R1-ospf-100-area-0.0.0.0]network 192.168.100.9 0.0.0.0
[R1-ospf-100-area-0.0.0.0]network 192.168.100.17 0.0.0.0
[R1-ospf-100-area-0.0.0.0]network 1.1.1.1 0.0.0.0
[R1-ospf-100-area-0.0.0.0]q
[R1-ospf-100]q
[R1]

R2:

[R2]ospf 100 router-id 2.2.2.2
[R2-ospf-100]area 0
[R2-ospf-100-area-0.0.0.0]network 192.168.100.13 0.0.0.0
[R2-ospf-100-area-0.0.0.0]network 192.168.100.6 0.0.0.0
[R2-ospf-100-area-0.0.0.0]network 2.2.2.2 0.0.0.0
[R2-ospf-100-area-0.0.0.0]q
[R2-ospf-100]q
[R2]

R3:

[R3]ospf 100 router-id 3.3.3.3
[R3-ospf-100]area 0
[R3-ospf-100-area-0.0.0.0]network 192.168.100.10 0.0.0.0
[R3-ospf-100-area-0.0.0.0]network 192.168.1.254 0.0.0.0
[R3-ospf-100-area-0.0.0.0]network 192.168.100.1 0.0.0.0
[R3-ospf-100-area-0.0.0.0]network 192.168.100.5 0.0.0.0
[R3-ospf-100-area-0.0.0.0]q
[R3-ospf-100]q
[R3]

R4:

[R4]ospf 100 router-id 4.4.4.4
[R4-ospf-100]area 0
[R4-ospf-100-area-0.0.0.0]network 192.168.100.14 0.0.0.0
[R4-ospf-100-area-0.0.0.0]network 192.168.2.254 0.0.0.0
[R4-ospf-100-area-0.0.0.0]network 192.168.100.2 0.0.0.0
[R4-ospf-100-area-0.0.0.0]network 192.168.100.18 0.0.0.0
[R4-ospf-100-area-0.0.0.0]q
[R4-ospf-100]q
[R4]

查看邻居关系:
R1:

[R1]display ospf peer brief 
	 OSPF Process 100 with Router ID 1.1.1.1
		  Peer Statistic Information
 ----------------------------------------------------------------------------
 Area Id          Interface                        Neighbor id      State    
 0.0.0.0          GigabitEthernet0/0/0             3.3.3.3          Full        
 0.0.0.0          GigabitEthernet0/0/2             4.4.4.4          Full        
 ----------------------------------------------------------------------------
[R1]

R2:

[R2]display ospf peer brief 
	 OSPF Process 100 with Router ID 2.2.2.2
		  Peer Statistic Information
 ----------------------------------------------------------------------------
 Area Id          Interface                        Neighbor id      State    
 0.0.0.0          GigabitEthernet3/0/0             3.3.3.3          Full        
 0.0.0.0          GigabitEthernet4/0/0             4.4.4.4          Full        
 ----------------------------------------------------------------------------
[R2]

R3:

[R3]display ospf peer brief 
	 OSPF Process 100 with Router ID 3.3.3.3
		  Peer Statistic Information
 ----------------------------------------------------------------------------
 Area Id          Interface                        Neighbor id      State    
 0.0.0.0          GigabitEthernet0/0/0             1.1.1.1          Full        
 0.0.0.0          GigabitEthernet0/0/1             2.2.2.2          Full        
 0.0.0.0          GigabitEthernet0/0/2             4.4.4.4          Full        
 ----------------------------------------------------------------------------
[R3]

R4:

[R4]display ospf peer brief 
	 OSPF Process 100 with Router ID 4.4.4.4
		  Peer Statistic Information
 ----------------------------------------------------------------------------
 Area Id          Interface                        Neighbor id      State    
 0.0.0.0          GigabitEthernet0/0/0             2.2.2.2          Full        
 0.0.0.0          GigabitEthernet0/0/1             1.1.1.1          Full        
 0.0.0.0          GigabitEthernet0/0/2             3.3.3.3          Full        
 ----------------------------------------------------------------------------
[R4]

骨干网

R5:

[R5]ospf 10 router-id 5.5.5.5
[R5-ospf-10]area 0
[R5-ospf-10-area-0.0.0.0]network 10.10.10.21 0.0.0.0
[R5-ospf-10-area-0.0.0.0]network 10.10.10.17 0.0.0.0
[R5-ospf-10-area-0.0.0.0]network 5.5.5.5 0.0.0.0
[R5-ospf-10-area-0.0.0.0]q
[R5-ospf-10]q
[R5]

R6:

[R6]ospf 10 router-id 6.6.6.6
[R6-ospf-10]area 0
[R6-ospf-10-area-0.0.0.0]network 10.10.10.25 0.0.0.0
[R6-ospf-10-area-0.0.0.0]network 10.10.10.18 0.0.0.0
[R6-ospf-10-area-0.0.0.0]network 6.6.6.6 0.0.0.0
[R6-ospf-10-area-0.0.0.0]q
[R6-ospf-10]q
[R6]

R7:

[R7]ospf 10 router-id 7.7.7.7
[R7-ospf-10]area 0
[R7-ospf-10-area-0.0.0.0]network 10.10.10.22 0.0.0.0
[R7-ospf-10-area-0.0.0.0]network 10.10.10.26 0.0.0.0
[R7-ospf-10-area-0.0.0.0]network 10.10.10.29 0.0.0.0
[R7-ospf-10-area-0.0.0.0]network 10.10.10.33 0.0.0.0
[R7-ospf-10-area-0.0.0.0]network 7.7.7.7 0.0.0.0
[R7-ospf-10-area-0.0.0.0]q
[R7-ospf-10]q
[R7]q

R8:

[R8]ospf 10 router-id 8.8.8.8
[R8-ospf-10]area 0	
[R8-ospf-10-area-0.0.0.0]network 10.10.10.30 0.0.0.0
[R8-ospf-10-area-0.0.0.0]network 10.10.10.34 0.0.0.0
[R8-ospf-10-area-0.0.0.0]network 8.8.8.8 0.0.0.0
[R8-ospf-10-area-0.0.0.0]q
[R8-ospf-10]q
[R8]

查看邻居表:
R5:

[R5]display ospf peer brief 
	 OSPF Process 10 with Router ID 5.5.5.5
		  Peer Statistic Information
 ----------------------------------------------------------------------------
 Area Id          Interface                        Neighbor id      State    
 0.0.0.0          GigabitEthernet0/0/2             7.7.7.7          Full        
 0.0.0.0          GigabitEthernet2/0/0             6.6.6.6          Full        
 ----------------------------------------------------------------------------
[R5]

R6:

[R6]display ospf peer brief 
	 OSPF Process 10 with Router ID 6.6.6.6
		  Peer Statistic Information
 ----------------------------------------------------------------------------
 Area Id          Interface                        Neighbor id      State    
 0.0.0.0          GigabitEthernet3/0/0             5.5.5.5          Full        
 0.0.0.0          GigabitEthernet0/0/2             7.7.7.7          Full        
 ----------------------------------------------------------------------------
[R6]

R7:

[R7]display ospf peer brief 
	 OSPF Process 10 with Router ID 7.7.7.7
		  Peer Statistic Information
 ----------------------------------------------------------------------------
 Area Id          Interface                        Neighbor id      State    
 0.0.0.0          GigabitEthernet0/0/0             5.5.5.5          Full        
 0.0.0.0          GigabitEthernet0/0/1             6.6.6.6          Full        
 0.0.0.0          GigabitEthernet0/0/2             8.8.8.8          Full        
 0.0.0.0          GigabitEthernet4/0/0             8.8.8.8          Full        
 ----------------------------------------------------------------------------
[R7]

R8:

[R8]display ospf peer brief 
	 OSPF Process 10 with Router ID 8.8.8.8
		  Peer Statistic Information
 ----------------------------------------------------------------------------
 Area Id          Interface                        Neighbor id      State    
 0.0.0.0          GigabitEthernet0/0/0             7.7.7.7          Full        
 0.0.0.0          GigabitEthernet0/0/1             7.7.7.7          Full        
 ----------------------------------------------------------------------------
[R8]

4、配置BGP建立邻居关系

总部

R1:

[R1]bgp 100
[R1-bgp]router-id 1.1.1.1
[R1-bgp]peer 2.2.2.2 as-number 100	
[R1-bgp]peer 2.2.2.2 connect-interface LoopBack 0
[R1-bgp]peer 10.10.10.2 as-number 200
[R1-bgp]peer 10.10.10.6 as-number 200
[R1-bgp]q
[R1]

R2:

[R2]bgp 100
[R2-bgp]router-id 2.2.2.2
[R2-bgp]peer 1.1.1.1 as-number 100
[R2-bgp]peer 1.1.1.1 connect-interface LoopBack 0
[R2-bgp]peer 10.10.10.10 as-number 200
[R2-bgp]peer 10.10.10.14 as-number 200
[R2-bgp]q
[R2]

查看你对等体关系建立:
R1:

[R1]display bgp peer 
 BGP local router ID : 1.1.1.1
 Local AS number : 100
 Total number of peers : 3		  Peers in established state : 3
  Peer            V          AS  MsgRcvd  MsgSent  OutQ  Up/Down       State Pre
fRcv

  2.2.2.2         4         100       25       26     0 00:23:19 Established    
   0
  10.10.10.2      4         200       16       17     0 00:14:08 Established    
   0
  10.10.10.6      4         200       12       13     0 00:10:56 Established    
   0
[R1]

R2:

[R2]display bgp peer 
 BGP local router ID : 2.2.2.2
 Local AS number : 100
 Total number of peers : 3		  Peers in established state : 3
  Peer            V          AS  MsgRcvd  MsgSent  OutQ  Up/Down       State Pre
fRcv
  1.1.1.1         4         100       25       25     0 00:23:53 Established    
   0
  10.10.10.10     4         200       16       17     0 00:14:37 Established    
   0
  10.10.10.14     4         200       11       12     0 00:09:23 Established    
   0
[R2]

骨干网

R5:

[R5]bgp 200
[R5-bgp]router-id 5.5.5.5
[R5-bgp]peer 10.10.10.1 as-number 100
[R5-bgp]peer 10.10.10.9 as-number 100
[R5-bgp]peer 6.6.6.6 as-number 200
[R5-bgp]peer 6.6.6.6 connect-interface LoopBack 0
[R5-bgp]peer 7.7.7.7 as-number 200
[R5-bgp]peer 7.7.7.7 connect-interface LoopBack 0
[R5-bgp]peer 8.8.8.8 as-number 200
[R5-bgp]peer 8.8.8.8 connect-interface LoopBack 0
[R5-bgp]q
[R5]

R6:

[R6]bgp 200
[R6-bgp]router-id 6.6.6.6
[R6-bgp]peer 10.10.10.5 as-number 100
[R6-bgp]peer 10.10.10.13 as-number 100
[R6-bgp]peer 5.5.5.5 as-number 200
[R6-bgp]peer 5.5.5.5 connect-interface LoopBack 0
[R6-bgp]peer 7.7.7.7 as-number 200
[R6-bgp]peer 7.7.7.7 connect-interface LoopBack 
[R6-bgp]peer 8.8.8.8 as-number 200
[R6-bgp]peer 8.8.8.8 connect-interface LoopBack 0
[R6-bgp]q
[R6]

R7:

[R7]bgp 200
[R7-bgp]router-id 7.7.7.7
[R7-bgp]peer 5.5.5.5 as-number 200	
[R7-bgp]peer 5.5.5.5 connect-interface LoopBack 0
[R7-bgp]peer 6.6.6.6 as-number 200
[R7-bgp]peer 6.6.6.6 connect-interface LoopBack 0
[R7-bgp]peer 8.8.8.8 as-number 200	
[R7-bgp]peer 8.8.8.8 connect-interface LoopBack 0
[R7-bgp]q
[R7]

R8:

[R8]bgp 200
[R8-bgp]router-id 8.8.8.8
[R8-bgp]peer 7.7.7.7 as-number 200
[R8-bgp]peer 7.7.7.7 connect-interface LoopBack 0
[R8-bgp]peer 6.6.6.6 as	
[R8-bgp]peer 6.6.6.6 as-number 200	
[R8-bgp]peer 6.6.6.6 connect-interface LoopBack 0
[R8-bgp]peer 5.5.5.5 as-number 200
[R8-bgp]peer 5.5.5.5 connect-interface LoopBack 0
[R8-bgp]peer 10.10.10.38 as-number 100
[R8-bgp]q
[R8]

查看对等体关系建立:
R5:

[R5]display bgp peer 

 BGP local router ID : 5.5.5.5
 Local AS number : 200
 Total number of peers : 5		  Peers in established state : 5
  Peer            V          AS  MsgRcvd  MsgSent  OutQ  Up/Down       State Pre
fRcv

  6.6.6.6         4         200       11       13     0 00:09:06 Established    
   0
  7.7.7.7         4         200        8       10     0 00:06:25 Established    
   0
  8.8.8.8         4         200        5        7     0 00:03:38 Established    
   0
  10.10.10.1      4         100       16       16     0 00:14:51 Established    
   0
  10.10.10.9      4         100       16       16     0 00:14:46 Established    
   0
[R5]

R6:

[R6]display bgp peer 
 BGP local router ID : 6.6.6.6
 Local AS number : 200
 Total number of peers : 5		  Peers in established state : 5
  Peer            V          AS  MsgRcvd  MsgSent  OutQ  Up/Down       State Pre
fRcv
  5.5.5.5         4         200       11       11     0 00:09:06 Established    
   0
  7.7.7.7         4         200        8       10     0 00:06:04 Established    
   0
  8.8.8.8         4         200        5        7     0 00:03:56 Established    
   0
  10.10.10.5      4         100       13       13     0 00:11:40 Established    
   0
  10.10.10.13     4         100       11       11     0 00:09:33 Established    
   0
[R6]

R7:

[R7]display bgp peer 
 BGP local router ID : 7.7.7.7
 Local AS number : 200
 Total number of peers : 3		  Peers in established state : 3
  Peer            V          AS  MsgRcvd  MsgSent  OutQ  Up/Down       State Pre
fRcv
  5.5.5.5         4         200        8        8     0 00:06:27 Established    
   0
  6.6.6.6         4         200        8        8     0 00:06:05 Established    
   0
  8.8.8.8         4         200        6        7     0 00:04:15 Established    
   0
[R7]

R8:

[R8]display bgp peer 
 BGP local router ID : 8.8.8.8
 Local AS number : 200
 Total number of peers : 4		  Peers in established state : 4
  Peer            V          AS  MsgRcvd  MsgSent  OutQ  Up/Down       State Pre
fRcv
  5.5.5.5         4         200        5        5     0 00:03:40 Established    
   0
  6.6.6.6         4         200        5        5     0 00:03:57 Established    
   0
  7.7.7.7         4         200        6        6     0 00:04:15 Established    
   0
  10.10.10.38     4         100        3        5     0 00:01:26 Established    
   0
[R8]

分部

R9:

[R9]bgp 100
[R9-bgp]router-id 9.9.9.9
[R9-bgp]peer 10.10.10.37 as-number 200
[R9-bgp]q
[R9]

查看对等体关系建立:

[R9]display bgp peer 
 BGP local router ID : 9.9.9.9
 Local AS number : 100
 Total number of peers : 1		  Peers in established state : 1
  Peer            V          AS  MsgRcvd  MsgSent  OutQ  Up/Down       State Pre
fRcv
  10.10.10.37     4         200        3        3     0 00:01:27 Established    
   0
[R9]

5、发布用户网段

R1:

[R1]bgp 100
[R1-bgp]network 192.168.1.0 24
[R1-bgp]network 192.168.2.0 24
[R1-bgp]q
[R1]

R2:

[R2]bgp 100
[R2-bgp]network 192.168.1.0 24
[R2-bgp]network 192.168.2.0 24
[R2-bgp]q
[R2]

R9:

[R9]bgp 100
[R9-bgp]network 192.168.3.0 24
[R9-bgp]network 192.168.4.0 24
[R9-bgp]q
[R9]

查看发布接收情况:
R1:

[R1]display bgp routing-table 
 BGP Local router ID is 1.1.1.1 
 Status codes: * - valid, > - best, d - damped,
               h - history,  i - internal, s - suppressed, S - Stale
               Origin : i - IGP, e - EGP, ? - incomplete
 Total Number of Routes: 4
      Network            NextHop        MED        LocPrf    PrefVal Path/Ogn
 *>   192.168.1.0        0.0.0.0         2                     0      i
 * i                     2.2.2.2         2          100        0      i
 *>   192.168.2.0        0.0.0.0         2                     0      i
 * i                     2.2.2.2         2          100        0      i
[R1]

R2:

[R2]display bgp routing-table 
 BGP Local router ID is 2.2.2.2 
 Status codes: * - valid, > - best, d - damped,
               h - history,  i - internal, s - suppressed, S - Stale
               Origin : i - IGP, e - EGP, ? - incomplete
 Total Number of Routes: 4
      Network            NextHop        MED        LocPrf    PrefVal Path/Ogn
 *>   192.168.1.0        0.0.0.0         2                     0      i
 * i                     1.1.1.1         2          100        0      i
 *>   192.168.2.0        0.0.0.0         2                     0      i
 * i                     1.1.1.1         2          100        0      i
[R2]

R9:

[R9]display bgp routing-table 
 BGP Local router ID is 9.9.9.9 
 Status codes: * - valid, > - best, d - damped,
               h - history,  i - internal, s - suppressed, S - Stale
               Origin : i - IGP, e - EGP, ? - incomplete
 Total Number of Routes: 2
      Network            NextHop        MED        LocPrf    PrefVal Path/Ogn
 *>   192.168.3.0        0.0.0.0         2                     0      i
 *>   192.168.4.0        0.0.0.0         2                     0      i
[R9]

R5:

[R5]display bgp routing-table 
 BGP Local router ID is 5.5.5.5 
 Status codes: * - valid, > - best, d - damped,
               h - history,  i - internal, s - suppressed, S - Stale
               Origin : i - IGP, e - EGP, ? - incomplete
 Total Number of Routes: 8
      Network            NextHop        MED        LocPrf    PrefVal Path/Ogn
 *>   192.168.1.0        10.10.10.1      2                     0      100i
 *                       10.10.10.9      2                     0      100i
   i                     10.10.10.5      2          100        0      100i
 *>   192.168.2.0        10.10.10.1      2                     0      100i
 *                       10.10.10.9      2                     0      100i
   i                     10.10.10.5      2          100        0      100i
   i  192.168.3.0        10.10.10.38     2          100        0      100i
   i  192.168.4.0        10.10.10.38     2          100        0      100i
[R5]

R6:

[R6]display bgp routing-table 
 BGP Local router ID is 6.6.6.6 
 Status codes: * - valid, > - best, d - damped,
               h - history,  i - internal, s - suppressed, S - Stale
               Origin : i - IGP, e - EGP, ? - incomplete
 Total Number of Routes: 8
      Network            NextHop        MED        LocPrf    PrefVal Path/Ogn
 *>   192.168.1.0        10.10.10.5      2                     0      100i
 *                       10.10.10.13     2                     0      100i
   i                     10.10.10.1      2          100        0      100i
 *>   192.168.2.0        10.10.10.5      2                     0      100i
 *                       10.10.10.13     2                     0      100i
   i                     10.10.10.1      2          100        0      100i
   i  192.168.3.0        10.10.10.38     2          100        0      100i
   i  192.168.4.0        10.10.10.38     2          100        0      100i
[R6]

R7:

[R7]display bgp routing-table 
 BGP Local router ID is 7.7.7.7 
 Status codes: * - valid, > - best, d - damped,
               h - history,  i - internal, s - suppressed, S - Stale
               Origin : i - IGP, e - EGP, ? - incomplete
 Total Number of Routes: 6
      Network            NextHop        MED        LocPrf    PrefVal Path/Ogn
   i  192.168.1.0        10.10.10.1      2          100        0      100i
   i                     10.10.10.5      2          100        0      100i
   i  192.168.2.0        10.10.10.1      2          100        0      100i
   i                     10.10.10.5      2          100        0      100i
   i  192.168.3.0        10.10.10.38     2          100        0      100i
   i  192.168.4.0        10.10.10.38     2          100        0      100i
[R7]

R8:

[R8]display bgp routing-table 
 BGP Local router ID is 8.8.8.8 
 Status codes: * - valid, > - best, d - damped,
               h - history,  i - internal, s - suppressed, S - Stale
               Origin : i - IGP, e - EGP, ? - incomplete
 Total Number of Routes: 6
      Network            NextHop        MED        LocPrf    PrefVal Path/Ogn
   i  192.168.1.0        10.10.10.1      2          100        0      100i
   i                     10.10.10.5      2          100        0      100i
   i  192.168.2.0        10.10.10.1      2          100        0      100i
   i                     10.10.10.5      2          100        0      100i
 *>   192.168.3.0        10.10.10.38     2                     0      100i
 *>   192.168.4.0        10.10.10.38     2                     0      100i
[R8]

6、将下一跳改为本地

R5:

[R5]bgp 200
[R5-bgp]peer 7.7.7.7 next-hop-local
[R5-bgp]peer 8.8.8.8 next-hop-local
[R5-bgp]q
[R5]

R6:

[R6]bgp 200
[R6-bgp]peer 7.7.7.7 next-hop-local
[R6-bgp]peer 8.8.8.8 next-hop-local
[R6-bgp]q
[R6]

R8:

[R8]bgp 200
[R8-bgp]peer 5.5.5.5 next-hop-local
[R8-bgp]peer 6.6.6.6 next-hop-local
[R8-bgp]peer 7.7.7.7 next-hop-local
[R8-bgp]q
[R8]

查看接收情况:
R5:

[R5]display bgp routing-table 
 BGP Local router ID is 5.5.5.5 
 Status codes: * - valid, > - best, d - damped,
               h - history,  i - internal, s - suppressed, S - Stale
               Origin : i - IGP, e - EGP, ? - incomplete
 Total Number of Routes: 8
      Network            NextHop        MED        LocPrf    PrefVal Path/Ogn
 *>   192.168.1.0        10.10.10.1      2                     0      100i
 *                       10.10.10.9      2                     0      100i
   i                     10.10.10.5      2          100        0      100i
 *>   192.168.2.0        10.10.10.1      2                     0      100i
 *                       10.10.10.9      2                     0      100i
   i                     10.10.10.5      2          100        0      100i
 *>i  192.168.3.0        8.8.8.8         2          100        0      100i
 *>i  192.168.4.0        8.8.8.8         2          100        0      100i
[R5]

R6:

[R6]display bgp routing-table 
 BGP Local router ID is 6.6.6.6 
 Status codes: * - valid, > - best, d - damped,
               h - history,  i - internal, s - suppressed, S - Stale
               Origin : i - IGP, e - EGP, ? - incomplete
 Total Number of Routes: 8
      Network            NextHop        MED        LocPrf    PrefVal Path/Ogn
 *>   192.168.1.0        10.10.10.5      2                     0      100i
 *                       10.10.10.13     2                     0      100i
   i                     10.10.10.1      2          100        0      100i
 *>   192.168.2.0        10.10.10.5      2                     0      100i
 *                       10.10.10.13     2                     0      100i
   i                     10.10.10.1      2          100        0      100i
 *>i  192.168.3.0        8.8.8.8         2          100        0      100i
 *>i  192.168.4.0        8.8.8.8         2          100        0      100i
[R6]

R7:

[R7]display bgp routing-table
 BGP Local router ID is 7.7.7.7 
 Status codes: * - valid, > - best, d - damped,
               h - history,  i - internal, s - suppressed, S - Stale
               Origin : i - IGP, e - EGP, ? - incomplete
 Total Number of Routes: 6
      Network            NextHop        MED        LocPrf    PrefVal Path/Ogn

 *>i  192.168.1.0        5.5.5.5         2          100        0      100i
 * i                     6.6.6.6         2          100        0      100i
 *>i  192.168.2.0        5.5.5.5         2          100        0      100i
 * i                     6.6.6.6         2          100        0      100i
 *>i  192.168.3.0        8.8.8.8         2          100        0      100i
 *>i  192.168.4.0        8.8.8.8         2          100        0      100i
[R7]

R8:

[R8]display bgp routing-table 
 BGP Local router ID is 8.8.8.8 
 Status codes: * - valid, > - best, d - damped,
               h - history,  i - internal, s - suppressed, S - Stale
               Origin : i - IGP, e - EGP, ? - incomplete
 Total Number of Routes: 6
      Network            NextHop        MED        LocPrf    PrefVal Path/Ogn
 *>i  192.168.1.0        5.5.5.5         2          100        0      100i
 * i                     6.6.6.6         2          100        0      100i
 *>i  192.168.2.0        5.5.5.5         2          100        0      100i
 * i                     6.6.6.6         2          100        0      100i
 *>   192.168.3.0        10.10.10.38     2                     0      100i
 *>   192.168.4.0        10.10.10.38     2                     0      100i
[R8]

7、允许AS重复

R1:

[R1]bgp 100
[R1-bgp]peer 10.10.10.2 allow-as-loop 
[R1-bgp]peer 10.10.10.6 allow-as-loop 
[R1-bgp]q
[R1]

R2:

[R2]bgp 100
[R2-bgp]peer 10.10.10.10 allow-as-loop
[R2-bgp]peer 10.10.10.14 allow-as-loop 
[R2-bgp]q
[R2]

R9:

[R9]bgp 100
[R9-bgp]peer 10.10.10.37 allow-as-loop 
[R9-bgp]q
[R9]

查看接收情况:
R1:

[R1]display bgp routing-table 
 BGP Local router ID is 1.1.1.1 
 Status codes: * - valid, > - best, d - damped,
               h - history,  i - internal, s - suppressed, S - Stale
               Origin : i - IGP, e - EGP, ? - incomplete
 Total Number of Routes: 14
      Network            NextHop        MED        LocPrf    PrefVal Path/Ogn
 *>   192.168.1.0        0.0.0.0         2                     0      i
 * i                     2.2.2.2         2          100        0      i
 *                       10.10.10.2                            0      200 100i
 *                       10.10.10.6                            0      200 100i
 *>   192.168.2.0        0.0.0.0         2                     0      i
 * i                     2.2.2.2         2          100        0      i
 *                       10.10.10.2                            0      200 100i
 *                       10.10.10.6                            0      200 100i
 *>   192.168.3.0        10.10.10.2                            0      200 100i
 *                       10.10.10.6                            0      200 100i
   i                     10.10.10.10                100        0      200 100i
 *>   192.168.4.0        10.10.10.2                            0      200 100i
 *                       10.10.10.6                            0      200 100i
   i                     10.10.10.10                100        0      200 100i
[R1]

R2:

[R2]display bgp routing-table 
 BGP Local router ID is 2.2.2.2 
 Status codes: * - valid, > - best, d - damped,
               h - history,  i - internal, s - suppressed, S - Stale
               Origin : i - IGP, e - EGP, ? - incomplete
 Total Number of Routes: 14
      Network            NextHop        MED        LocPrf    PrefVal Path/Ogn
 *>   192.168.1.0        0.0.0.0         2                     0      i
 * i                     1.1.1.1         2          100        0      i
 *                       10.10.10.10                           0      200 100i
 *                       10.10.10.14                           0      200 100i
 *>   192.168.2.0        0.0.0.0         2                     0      i
 * i                     1.1.1.1         2          100        0      i
 *                       10.10.10.10                           0      200 100i
 *                       10.10.10.14                           0      200 100i
 *>   192.168.3.0        10.10.10.10                           0      200 100i
 *                       10.10.10.14                           0      200 100i
   i                     10.10.10.2                 100        0      200 100i
 *>   192.168.4.0        10.10.10.10                           0      200 100i
 *                       10.10.10.14                           0      200 100i
   i                     10.10.10.2                 100        0      200 100i
[R2]

R9:

[R9]display bgp routing-table 
 BGP Local router ID is 9.9.9.9 
 Status codes: * - valid, > - best, d - damped,
               h - history,  i - internal, s - suppressed, S - Stale
               Origin : i - IGP, e - EGP, ? - incomplete
 Total Number of Routes: 4
      Network            NextHop        MED        LocPrf    PrefVal Path/Ogn
 *>   192.168.1.0        10.10.10.37                           0      200 100i
 *>   192.168.2.0        10.10.10.37                           0      200 100i
 *>   192.168.3.0        0.0.0.0         2                     0      i
 *>   192.168.4.0        0.0.0.0         2                     0      i
[R9]

8、重发布

R1:

[R1]ospf 100
[R1-ospf-100]import-route bgp 
[R1-ospf-100]q
[R1]

R2:

[R2]ospf 100	
[R2-ospf-100]import-route bgp 
[R2-ospf-100]q
[R2

R9:

[R9]ospf 200
[R9-ospf-200]import-route bgp 
[R9-ospf-200]q
[R9]

查看R3,R4以及R10的路由表:
R3:

[R3]display ip routing-table protocol ospf 
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Public routing table : OSPF
         Destinations : 7        Routes : 9        
OSPF routing table status : <Active>
         Destinations : 7        Routes : 9
Destination/Mask    Proto   Pre  Cost      Flags NextHop         Interface
        1.1.1.1/32  OSPF    10   1           D   192.168.100.9   GigabitEthernet
0/0/0
        2.2.2.2/32  OSPF    10   1           D   192.168.100.6   GigabitEthernet
0/0/1
    192.168.2.0/24  OSPF    10   2           D   192.168.100.2   GigabitEthernet
0/0/2
    192.168.3.0/24  O_ASE   150  1           D   192.168.100.9   GigabitEthernet
0/0/0
    192.168.4.0/24  O_ASE   150  1           D   192.168.100.9   GigabitEthernet
0/0/0
 192.168.100.12/30  OSPF    10   2           D   192.168.100.2   GigabitEthernet
0/0/2
                    OSPF    10   2           D   192.168.100.6   GigabitEthernet
0/0/1
 192.168.100.16/30  OSPF    10   2           D   192.168.100.9   GigabitEthernet
0/0/0
                    OSPF    10   2           D   192.168.100.2   GigabitEthernet
0/0/2

OSPF routing table status : <Inactive>
         Destinations : 0        Routes : 0

[R3]

R4:

[R4]display ip routing-table protocol ospf 
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Public routing table : OSPF
         Destinations : 7        Routes : 9        
OSPF routing table status : <Active>
         Destinations : 7        Routes : 9
Destination/Mask    Proto   Pre  Cost      Flags NextHop         Interface
        1.1.1.1/32  OSPF    10   1           D   192.168.100.17  GigabitEthernet
0/0/1
        2.2.2.2/32  OSPF    10   1           D   192.168.100.13  GigabitEthernet
0/0/0
    192.168.1.0/24  OSPF    10   2           D   192.168.100.1   GigabitEthernet
0/0/2
    192.168.3.0/24  O_ASE   150  1           D   192.168.100.17  GigabitEthernet
0/0/1
    192.168.4.0/24  O_ASE   150  1           D   192.168.100.17  GigabitEthernet
0/0/1
  192.168.100.4/30  OSPF    10   2           D   192.168.100.1   GigabitEthernet
0/0/2
                    OSPF    10   2           D   192.168.100.13  GigabitEthernet
0/0/0
  192.168.100.8/30  OSPF    10   2           D   192.168.100.1   GigabitEthernet
0/0/2
                    OSPF    10   2           D   192.168.100.17  GigabitEthernet
0/0/1

OSPF routing table status : <Inactive>
         Destinations : 0        Routes : 0

[R4]

R10:

[R10]display ip routing-table protocol ospf
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Public routing table : OSPF
         Destinations : 2        Routes : 2        

OSPF routing table status : <Active>
         Destinations : 2        Routes : 2
Destination/Mask    Proto   Pre  Cost      Flags NextHop         Interface
    192.168.1.0/24  O_ASE   150  1           D   192.168.200.2   GigabitEthernet
0/0/0
    192.168.2.0/24  O_ASE   150  1           D   192.168.200.2   GigabitEthernet
0/0/0

OSPF routing table status : <Inactive>
         Destinations : 0        Routes : 0
[R10]

测试:
HCIP——前期综合实验,计算机网络,HCIP,智能路由器,网络,服务器,网络协议,计算机网络,HCIP,华为

9、修改BGP优先级

R1:

[R1]bgp 100
[R1-bgp]ipv4-family unicas
[R1-bgp-af-ipv4]preference 140 255 255
[R1-bgp-af-ipv4]q
[R1-bgp]q
[R1]

R2:

[R2]bgp 100
[R2-bgp]ipv4-family unicast 
[R2-bgp-af-ipv4]preference 140 255 255
[R2-bgp-af-ipv4]q
[R2-bgp]q
[R2]

查看路由表:
R1:

[R1]display ip routing-table protocol bgp 
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Public routing table : BGP
         Destinations : 2        Routes : 2        
BGP routing table status : <Active>
         Destinations : 2        Routes : 2
Destination/Mask    Proto   Pre  Cost      Flags NextHop         Interface
    192.168.3.0/24  EBGP    140  0           D   10.10.10.2      GigabitEthernet
2/0/0
    192.168.4.0/24  EBGP    140  0           D   10.10.10.2      GigabitEthernet
2/0/0
BGP routing table status : <Inactive>
         Destinations : 0        Routes : 0

[R1]

R2:

[R2]display ip routing-table protocol bgp 
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Public routing table : BGP
         Destinations : 2        Routes : 2        
BGP routing table status : <Active>
         Destinations : 2        Routes : 2
Destination/Mask    Proto   Pre  Cost      Flags NextHop         Interface
    192.168.3.0/24  EBGP    140  0           D   10.10.10.10     GigabitEthernet
0/0/1
    192.168.4.0/24  EBGP    140  0           D   10.10.10.10     GigabitEthernet
0/0/1
BGP routing table status : <Inactive>
         Destinations : 0        Routes : 0

[R2]

10、优化

(1)修改cost值

R1:

[R1]int g0/0/0
[R1-GigabitEthernet0/0/0]ospf cost 10

R2:

[R2]int g3/0/0
[R2-GigabitEthernet3/0/0]ospf cost 10

R3:

[R3]int g0/0/1
[R3-GigabitEthernet0/0/1]ospf cost 10

R4:

[R4]int g0/0/1
[R4-GigabitEthernet0/0/1]ospf cost 10

(2)修改MED值

R1:

[R1]ip ip-prefix 1 permit 192.168.2.0 24
[R1]route-policy 1 permit node 10
[R1-route-policy]if-match ip-prefix 1
[R1-route-policy]apply cost 10
[R1-route-policy]q
[R1]route-policy 1 permit node 20
[R1-route-policy]q
[R1]bgp 100
[R1-bgp]peer 10.10.10.2 route-policy 1 export 
[R1-bgp]peer 10.10.10.6 route-policy 1 export

R2:

[R2]ip ip-prefix 1 permit 192.168.1.0 24
[R2]route-policy 1 permit node 10
Info: New Sequence of this List.
[R2-route-policy]if-match ip-prefix 1
[R2-route-policy]apply cost 10
[R2-route-policy]q
[R2]route-policy 1 permit node 20
Info: New Sequence of this List.
[R2-route-policy]q
[R2]bgp 100
[R2-bgp]peer 10.10.10.10 route-policy 1 export 
[R2-bgp]peer 10.10.10.14 route-policy 1 export

R6:

[R6]route-policy 1 permit node 10
Info: New Sequence of this List.
[R6-route-policy]apply cost 10
[R6-route-policy]q
[R6]route-policy policy permit node 20
Info: New Sequence of this List.
[R6-route-policy]q
[R6]bgp 200
[R6-bgp]peer 10.10.10.5 route-policy 1 export 
[R6-bgp]peer 10.10.10.13 route-policy 1 export

(3)修改为type1

R1:

[R1]ospf 100
[R1-ospf-100]import-route bgp type 1
[R1-ospf-100]q
[R1]

R2:

[R2]ospf 100
[R2-ospf-100]import-route bgp type 1
[R2-ospf-100]q
[R2]

R9:

[R9]ospf 200	
[R9-ospf-200]import-route bgp type 1
[R9-ospf-200]q
[R9]

HCIP——前期综合实验,计算机网络,HCIP,智能路由器,网络,服务器,网络协议,计算机网络,HCIP,华为
HCIP——前期综合实验,计算机网络,HCIP,智能路由器,网络,服务器,网络协议,计算机网络,HCIP,华为文章来源地址https://www.toymoban.com/news/detail-622290.html

到了这里,关于HCIP——前期综合实验的文章就介绍完了。如果您还想了解更多内容,请在右上角搜索TOY模板网以前的文章或继续浏览下面的相关文章,希望大家以后多多支持TOY模板网!

本文来自互联网用户投稿,该文观点仅代表作者本人,不代表本站立场。本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如若转载,请注明出处: 如若内容造成侵权/违法违规/事实不符,请点击违法举报进行投诉反馈,一经查实,立即删除!

领支付宝红包 赞助服务器费用

相关文章

  • 计算机网络综合大实验验优(含抓包、两届实验对比)

    第一届智科牛马人的计网实验验优报告: 实验需要组队,三人一组好像,也可以一人两人,排名在前面的人验优更容易,同时需要操作四台电脑,跟着实验指导书,不懂的问问老师和身边同学,一天从早到晚可以搞定,开窍也可以一上午或者一下午搞定。 前面画的拓扑图越

    2024年02月11日
    浏览(44)
  • 计算机网络期末复习简答题、综合题、实验题答案整理汇总详细(持续更新中)

    简答题只背标黄的部分!!综合题和实验题全看!!! 1. TCP/IP 与 OSI 相结合的五层体系结构将计算机网络划分成哪几个层次?各层的主要功能是什么 第一层,物理层:物理层的任务就是透明地传送比特流。(注意:传递信息的物理媒体,如双绞线、同轴电缆、光缆等,是在

    2024年02月08日
    浏览(40)
  • HCIP——前期综合实验

    1、该拓扑为公司网络,其中包括公司总部、公司分部以及公司骨干网,不包含运营商公网部分。 2、设备名称均使用拓扑上名称改名,并且区分大小写。 3、整张拓扑均使用私网地址进行配置。 4、整张网络中,运行OSPF协议或者BGP协议的设备,其Router-id值为设备名数字号,例

    2024年02月14日
    浏览(44)
  • 计算机网络综合实训——网络程序设计

    计算机网络综合实训 网络程序设计 作者姓名 学号 所在院系 计算机与信息工程学院 学科专业名称 计算机科学与技术 导师及职称 柯宗武 教授 提交时间 2023/05/28 仿qq聊天的设计与实现 (指导教师,柯宗武 教授) (湖北师范大学计算机与信息工程学院 中国 黄石 435002) 一、

    2024年02月10日
    浏览(41)
  • 计算机网络 实验指导 实验17

    Table PC0 和 Table PC1 最开始可能还会连Access Point0,无影响后面会改 名称 接口 IP地址 网关地址 Router0 fa0/0 210.10.10.1 fa0/1 220.10.10.2 Tablet PC0 210.10.10.11 Tablet PC1 210.10.10.12 Wireless 互联网 220.10.10.2 LAN 192.168.0.1 PC0 0/1 192.168.0.10 192.168.0.1 PC1 192.168.0.11 192.168.0.1 PC2 192.168.0.12 192.168.0.1 Access p

    2024年04月15日
    浏览(70)
  • 软考系分之计算机网络规划设计、综合布线、RAID和网络存储等

      本篇重点介绍计算机网络中的网络规划设计、综合布线、RAID和网络存储。   三层模型分为核心层、汇聚层和接入层,接入层主要负责用户接入相关事宜,汇聚层主要负责用户接入后到核心业务之间的负载路由等等,核心层主要负责互联网不同业务之间高速的数据传送

    2024年01月23日
    浏览(46)
  • 计算机网络三个 实验

    目录 实验一 ipconfig 实作一 实作二 ping 实作一 实作二 tracert 实作一 实作二 ARP 实作一 实作二 实作三 DHCP 实作一 netstat 实作一 实作二 DNS 实作一 实作二 实作三 cache 实作一 实作二 实验二 准备 数据链路层 实作一 熟悉 Ethernet 帧结构 实作二 了解子网内/外通信时的 MAC 地址 实作

    2024年02月09日
    浏览(60)
  • 计算机网络实验

    自己计算机网络配置 ipconfig /all ​ 物理地址. . . . . . . . . . . . . : 00-E0-4C-68-04-91 IPv4 地址 . . . . . . . . . . . . : 10.60.55.199(首选) 子网掩码 . . . . . . . . . . . . : 255.254.0.0 默认网关. . . . . . . . . . . . . : 10.60.255.254 别人计算机网络配置 ipconfig /all ​ 物理地址. . . . . . . . . . . . . : 2C-F0-

    2024年01月16日
    浏览(48)
  • 计算机网络实验作业

    实验内容 1. 领取水晶头、网线、网线钳等,制作网线。利用测线仪测试制作好的网线是否正常? 正常 2. 双绞线分成非屏蔽双绞线和(屏蔽双绞线  ),(  屏蔽双绞线 )的屏蔽效果好,( 非屏蔽双绞线  )的价格便宜。 3. 根据绞合的密度区分不同类别的双绞线,如

    2024年02月06日
    浏览(67)
  • 计算机网络 实验二

    ⭐计网实验专栏,欢迎订阅与关注! ★观前提示 :本篇内容为计算机网络实验。内容可能会不符合每个人实验的要求,因此以下内容建议仅做思路参考。 一、实验目的 (1)掌握IP地址的基本结构(网络部分与主机部分的区分) (2)掌握子网掩码的含义 (3)掌握IP包的组成格

    2023年04月17日
    浏览(58)

觉得文章有用就打赏一下文章作者

支付宝扫一扫打赏

博客赞助

微信扫一扫打赏

请作者喝杯咖啡吧~博客赞助

支付宝扫一扫领取红包,优惠每天领

二维码1

领取红包

二维码2

领红包