set_property PACKAGE_PIN
set_property PACKAGE_PIN AF25 [get_ports rst]
将信号名rst绑定AF25引脚,其他信号同理
set_property IOSTANDARD LVCMOS33
set_property IOSTANDARD LVCMOS33 [get_ports rst]
将信号名rst电平定义为LVCMOS33,就是3.3v电平
set_property PULLDOWN true [get_ports rst]
将信号名rst下拉,非必须。上拉PULLUP
约束好保存编译即可。
在写.sdc约束文件时,要做的第一件事情就是使用create_clock对进入FPGA的时钟进行约束。其语法格式如下
create_clock[-add] [-name <clock_name>] -period [-waveform<edge_list>]
参数解释:
-name表示生成的时钟名称
-period表示时钟周期,单位为ns
-waveform可以详细描述时钟占空比及其上下移位置
端口列表
-add用于为一个端口添加多个时钟约束
例子:
create_clock-period 10 -name clk_100 [get_ports clk]
生成了一个周期为10ns占空比为50%的时钟,其名字为clk_100,其端口名为clk
create_clock-period 10 -waveform {8 12} -name clk [get_ports clk]
生成一个周期为10ns上升沿8ns,下降沿2ns的时钟
create_clock-period 10 -name clk_100 [get_ports clk]
create_clock-perioid 6.6 -name clk_150 -add [get_ports clk]文章来源:https://www.toymoban.com/news/detail-650914.html
在clk一个端口上生成两个时钟,其周期分别为10ns和6.6ns。如果一个系统中同一个端口在不同时刻会有多种时钟输入,可以使用-add参数。否则,如果不添加-add参数,后面定义的时钟无效。文章来源地址https://www.toymoban.com/news/detail-650914.html
## This file is a general .xdc for the PYNQ-Z2 board
## To use it in a project:
## - uncomment the lines corresponding to used pins
## - rename the used ports (in each line, after get_ports) according to the top level signal names in the project
## Clock signal 125 MHz
#set_property -dict { PACKAGE_PIN H16 IOSTANDARD LVCMOS33 } [get_ports { sysclk }]; #IO_L13P_T2_MRCC_35 Sch=sysclk
#create_clock -add -name sys_clk_pin -period 8.00 -waveform {0 4} [get_ports { sysclk }];
##Switches
#set_property -dict { PACKAGE_PIN M20 IOSTANDARD LVCMOS33 } [get_ports { sw[0] }]; #IO_L7N_T1_AD2N_35 Sch=sw[0]
#set_property -dict { PACKAGE_PIN M19 IOSTANDARD LVCMOS33 } [get_ports { sw[1] }]; #IO_L7P_T1_AD2P_35 Sch=sw[1]
##RGB LEDs
#set_property -dict { PACKAGE_PIN L15 IOSTANDARD LVCMOS33 } [get_ports { led4_b }]; #IO_L22N_T3_AD7N_35 Sch=led4_b
#set_property -dict { PACKAGE_PIN G17 IOSTANDARD LVCMOS33 } [get_ports { led4_g }]; #IO_L16P_T2_35 Sch=led4_g
#set_property -dict { PACKAGE_PIN N15 IOSTANDARD LVCMOS33 } [get_ports { led4_r }]; #IO_L21P_T3_DQS_AD14P_35 Sch=led4_r
#set_property -dict { PACKAGE_PIN G14 IOSTANDARD LVCMOS33 } [get_ports { led5_b }]; #IO_0_35 Sch=led5_b
#set_property -dict { PACKAGE_PIN L14 IOSTANDARD LVCMOS33 } [get_ports { led5_g }]; #IO_L22P_T3_AD7P_35 Sch=led5_g
#set_property -dict { PACKAGE_PIN M15 IOSTANDARD LVCMOS33 } [get_ports { led5_r }]; #IO_L23N_T3_35 Sch=led5_r
##LEDs
#set_property -dict { PACKAGE_PIN R14 IOSTANDARD LVCMOS33 } [get_ports { led[0] }]; #IO_L6N_T0_VREF_34 Sch=led[0]
#set_property -dict { PACKAGE_PIN P14 IOSTANDARD LVCMOS33 } [get_ports { led[1] }]; #IO_L6P_T0_34 Sch=led[1]
#set_property -dict { PACKAGE_PIN N16 IOSTANDARD LVCMOS33 } [get_ports { led[2] }]; #IO_L21N_T3_DQS_AD14N_35 Sch=led[2]
#set_property -dict { PACKAGE_PIN M14 IOSTANDARD LVCMOS33 } [get_ports { led[3] }]; #IO_L23P_T3_35 Sch=led[3]
##Buttons
#set_property -dict { PACKAGE_PIN D19 IOSTANDARD LVCMOS33 } [get_ports { btn[0] }]; #IO_L4P_T0_35 Sch=btn[0]
#set_property -dict { PACKAGE_PIN D20 IOSTANDARD LVCMOS33 } [get_ports { btn[1] }]; #IO_L4N_T0_35 Sch=btn[1]
#set_property -dict { PACKAGE_PIN L20 IOSTANDARD LVCMOS33 } [get_ports { btn[2] }]; #IO_L9N_T1_DQS_AD3N_35 Sch=btn[2]
#set_property -dict { PACKAGE_PIN L19 IOSTANDARD LVCMOS33 } [get_ports { btn[3] }]; #IO_L9P_T1_DQS_AD3P_35 Sch=btn[3]
##PmodA
#set_property -dict { PACKAGE_PIN Y18 IOSTANDARD LVCMOS33 } [get_ports { ja[0] }]; #IO_L17P_T2_34 Sch=ja_p[1]
#set_property -dict { PACKAGE_PIN Y19 IOSTANDARD LVCMOS33 } [get_ports { ja[1] }]; #IO_L17N_T2_34 Sch=ja_n[1]
#set_property -dict { PACKAGE_PIN Y16 IOSTANDARD LVCMOS33 } [get_ports { ja[2] }]; #IO_L7P_T1_34 Sch=ja_p[2]
#set_property -dict { PACKAGE_PIN Y17 IOSTANDARD LVCMOS33 } [get_ports { ja[3] }]; #IO_L7N_T1_34 Sch=ja_n[2]
#set_property -dict { PACKAGE_PIN U18 IOSTANDARD LVCMOS33 } [get_ports { ja[4] }]; #IO_L12P_T1_MRCC_34 Sch=ja_p[3]
#set_property -dict { PACKAGE_PIN U19 IOSTANDARD LVCMOS33 } [get_ports { ja[5] }]; #IO_L12N_T1_MRCC_34 Sch=ja_n[3]
#set_property -dict { PACKAGE_PIN W18 IOSTANDARD LVCMOS33 } [get_ports { ja[6] }]; #IO_L22P_T3_34 Sch=ja_p[4]
#set_property -dict { PACKAGE_PIN W19 IOSTANDARD LVCMOS33 } [get_ports { ja[7] }]; #IO_L22N_T3_34 Sch=ja_n[4]
##PmodB
#set_property -dict { PACKAGE_PIN W14 IOSTANDARD LVCMOS33 } [get_ports { jb[0] }]; #IO_L8P_T1_34 Sch=jb_p[1]
#set_property -dict { PACKAGE_PIN Y14 IOSTANDARD LVCMOS33 } [get_ports { jb[1] }]; #IO_L8N_T1_34 Sch=jb_n[1]
#set_property -dict { PACKAGE_PIN T11 IOSTANDARD LVCMOS33 } [get_ports { jb[2] }]; #IO_L1P_T0_34 Sch=jb_p[2]
#set_property -dict { PACKAGE_PIN T10 IOSTANDARD LVCMOS33 } [get_ports { jb[3] }]; #IO_L1N_T0_34 Sch=jb_n[2]
#set_property -dict { PACKAGE_PIN V16 IOSTANDARD LVCMOS33 } [get_ports { jb[4] }]; #IO_L18P_T2_34 Sch=jb_p[3]
#set_property -dict { PACKAGE_PIN W16 IOSTANDARD LVCMOS33 } [get_ports { jb[5] }]; #IO_L18N_T2_34 Sch=jb_n[3]
#set_property -dict { PACKAGE_PIN V12 IOSTANDARD LVCMOS33 } [get_ports { jb[6] }]; #IO_L4P_T0_34 Sch=jb_p[4]
#set_property -dict { PACKAGE_PIN W13 IOSTANDARD LVCMOS33 } [get_ports { jb[7] }]; #IO_L4N_T0_34 Sch=jb_n[4]
##Audio
#set_property -dict { PACKAGE_PIN M17 IOSTANDARD LVCMOS33 } [get_ports { adr0 }]; #IO_L8P_T1_AD10P_35 Sch=adr0
#set_property -dict { PACKAGE_PIN M18 IOSTANDARD LVCMOS33 } [get_ports { adr1 }]; #IO_L8N_T1_AD10N_35 Sch=adr1
#set_property -dict { PACKAGE_PIN U5 IOSTANDARD LVCMOS33 } [get_ports { au_mclk_r }]; #IO_L19N_T3_VREF_13 Sch=au_mclk_r
#set_property -dict { PACKAGE_PIN T9 IOSTANDARD LVCMOS33 } [get_ports { au_sda_r }]; #IO_L12P_T1_MRCC_13 Sch=au_sda_r
#set_property -dict { PACKAGE_PIN U9 IOSTANDARD LVCMOS33 } [get_ports { au_scl_r }]; #IO_L17P_T2_13 Sch= au_scl_r
#set_property -dict { PACKAGE_PIN F17 IOSTANDARD LVCMOS33 } [get_ports { au_dout_r }]; #IO_L6N_T0_VREF_35 Sch=au_dout_r
#set_property -dict { PACKAGE_PIN G18 IOSTANDARD LVCMOS33 } [get_ports { au_din_r }]; #IO_L16N_T2_35 Sch=au_din_r
#set_property -dict { PACKAGE_PIN T17 IOSTANDARD LVCMOS33 } [get_ports { au_wclk_r }]; #IO_L20P_T3_34 Sch=au_wclk_r
#set_property -dict { PACKAGE_PIN R18 IOSTANDARD LVCMOS33 } [get_ports { au_bclk_r }]; #IO_L20N_T3_34 Sch=au_bclk_r
## Single Ended Analog Inputs
##NOTE: The ar_an_p pins can be used as single ended analog inputs with voltages from 0-3.3V (Arduino Analog pins a[0]-a[5]).
## These signals should only be connected to the XADC core. When using these pins as digital I/O, use pins a[0]-a[5].
#set_property -dict { PACKAGE_PIN E17 IOSTANDARD LVCMOS33 } [get_ports { ar_an0_p }]; #IO_L3P_T0_DQS_AD1P_35 Sch=ar_an0_p
#set_property -dict { PACKAGE_PIN D18 IOSTANDARD LVCMOS33 } [get_ports { ar_an0_n }]; #IO_L3P_T0_DQS_AD1P_35 Sch=ar_an0_n
#set_property -dict { PACKAGE_PIN E18 IOSTANDARD LVCMOS33 } [get_ports { ar_an1_p }]; #IO_L5N_T0_AD9P_35 Sch=ar_an1_p
#set_property -dict { PACKAGE_PIN E19 IOSTANDARD LVCMOS33 } [get_ports { ar_an1_n }]; #IO_L5N_T0_AD9N_35 Sch=ar_an1_n
#set_property -dict { PACKAGE_PIN K14 IOSTANDARD LVCMOS33 } [get_ports { ar_an2_p }]; #IO_L20P_T3_AD6P_35 Sch=ar_an2_p
#set_property -dict { PACKAGE_PIN J14 IOSTANDARD LVCMOS33 } [get_ports { ar_an2_n }]; #IO_L20P_T3_AD6N_35 Sch=ar_an2_n
#set_property -dict { PACKAGE_PIN K16 IOSTANDARD LVCMOS33 } [get_ports { ar_an3_p }]; #IO_L24P_T3_AD15P_35 Sch=ar_an3_p
#set_property -dict { PACKAGE_PIN J16 IOSTANDARD LVCMOS33 } [get_ports { ar_an3_n }]; #IO_L24P_T3_AD15N_35 Sch=ar_an3_n
#set_property -dict { PACKAGE_PIN J20 IOSTANDARD LVCMOS33 } [get_ports { ar_an4_p }]; #IO_L17P_T2_AD5P_35 Sch=ar_an4_p
#set_property -dict { PACKAGE_PIN H20 IOSTANDARD LVCMOS33 } [get_ports { ar_an4_n }]; #IO_L17P_T2_AD5P_35 Sch=ar_an4_n
#set_property -dict { PACKAGE_PIN G19 IOSTANDARD LVCMOS33 } [get_ports { ar_an5_p }]; #IO_L18P_T2_AD13P_35 Sch=ar_an5_p
#set_property -dict { PACKAGE_PIN G20 IOSTANDARD LVCMOS33 } [get_ports { ar_an5_n }]; #IO_L18P_T2_AD13P_35 Sch=ar_an5_n
##Arduino Digital I/O
#set_property -dict { PACKAGE_PIN T14 IOSTANDARD LVCMOS33 } [get_ports { ar[0] }]; #IO_L5P_T0_34 Sch=ar[0]
#set_property -dict { PACKAGE_PIN U12 IOSTANDARD LVCMOS33 } [get_ports { ar[1] }]; #IO_L2N_T0_34 Sch=ar[1]
#set_property -dict { PACKAGE_PIN U13 IOSTANDARD LVCMOS33 } [get_ports { ar[2] }]; #IO_L3P_T0_DQS_PUDC_B_34 Sch=ar[2]
#set_property -dict { PACKAGE_PIN V13 IOSTANDARD LVCMOS33 } [get_ports { ar[3] }]; #IO_L3N_T0_DQS_34 Sch=ar[3]
#set_property -dict { PACKAGE_PIN V15 IOSTANDARD LVCMOS33 } [get_ports { ar[4] }]; #IO_L10P_T1_34 Sch=ar[4]
#set_property -dict { PACKAGE_PIN T15 IOSTANDARD LVCMOS33 } [get_ports { ar[5] }]; #IO_L5N_T0_34 Sch=ar[5]
#set_property -dict { PACKAGE_PIN R16 IOSTANDARD LVCMOS33 } [get_ports { ar[6] }]; #IO_L19P_T3_34 Sch=ar[6]
#set_property -dict { PACKAGE_PIN U17 IOSTANDARD LVCMOS33 } [get_ports { ar[7] }]; #IO_L9N_T1_DQS_34 Sch=ar[7]
#set_property -dict { PACKAGE_PIN V17 IOSTANDARD LVCMOS33 } [get_ports { ar[8] }]; #IO_L21P_T3_DQS_34 Sch=ar[8]
#set_property -dict { PACKAGE_PIN V18 IOSTANDARD LVCMOS33 } [get_ports { ar[9] }]; #IO_L21N_T3_DQS_34 Sch=ar[9]
#set_property -dict { PACKAGE_PIN T16 IOSTANDARD LVCMOS33 } [get_ports { ar[10] }]; #IO_L9P_T1_DQS_34 Sch=ar[10]
#set_property -dict { PACKAGE_PIN R17 IOSTANDARD LVCMOS33 } [get_ports { ar[11] }]; #IO_L19N_T3_VREF_34 Sch=ar[11]
#set_property -dict { PACKAGE_PIN P18 IOSTANDARD LVCMOS33 } [get_ports { ar[12] }]; #IO_L23N_T3_34 Sch=ar[12]
#set_property -dict { PACKAGE_PIN N17 IOSTANDARD LVCMOS33 } [get_ports { ar[13] }]; #IO_L23P_T3_34 Sch=ar[13]
#set_property -dict { PACKAGE_PIN Y13 IOSTANDARD LVCMOS33 } [get_ports { a }]; #IO_L20N_T3_13 Sch=a
##Arduino Digital I/O On Outer Analog Header
##NOTE: These pins should be used when using the analog header signals A0-A5 as digital I/O
#set_property -dict { PACKAGE_PIN Y11 IOSTANDARD LVCMOS33 } [get_ports { a[0] }]; #IO_L18N_T2_13 Sch=a[0]
#set_property -dict { PACKAGE_PIN Y12 IOSTANDARD LVCMOS33 } [get_ports { a[1] }]; #IO_L20P_T3_13 Sch=a[1]
#set_property -dict { PACKAGE_PIN W11 IOSTANDARD LVCMOS33 } [get_ports { a[2] }]; #IO_L18P_T2_13 Sch=a[2]
#set_property -dict { PACKAGE_PIN V11 IOSTANDARD LVCMOS33 } [get_ports { a[3] }]; #IO_L21P_T3_DQS_13 Sch=a[3]
#set_property -dict { PACKAGE_PIN T5 IOSTANDARD LVCMOS33 } [get_ports { a[4] }]; #IO_L19P_T3_13 Sch=a[4]
#set_property -dict { PACKAGE_PIN U10 IOSTANDARD LVCMOS33 } [get_ports { a[5] }]; #IO_L12N_T1_MRCC_13 Sch=a[5]
## Arduino SPI
#set_property -dict { PACKAGE_PIN W15 IOSTANDARD LVCMOS33 } [get_ports { ck_miso }]; #IO_L10N_T1_34 Sch=miso
#set_property -dict { PACKAGE_PIN T12 IOSTANDARD LVCMOS33 } [get_ports { ck_mosi }]; #IO_L2P_T0_34 Sch=ar_mosi_r
#set_property -dict { PACKAGE_PIN H15 IOSTANDARD LVCMOS33 } [get_ports { ck_sck }]; #IO_L19P_T3_35 Sch=sck
#set_property -dict { PACKAGE_PIN F16 IOSTANDARD LVCMOS33 } [get_ports { ck_ss }]; #IO_L6P_T0_35 Sch=ss
## Arduino I2C
#set_property -dict { PACKAGE_PIN P16 IOSTANDARD LVCMOS33 } [get_ports { ar_scl }]; #IO_L24N_T3_34 Sch=ar_scl
#set_property -dict { PACKAGE_PIN P15 IOSTANDARD LVCMOS33 } [get_ports { ar_sda }]; #IO_L24P_T3_34 Sch=ar_sda
##Raspberry Digital I/O
#set_property -dict { PACKAGE_PIN W18 IOSTANDARD LVCMOS33 } [get_ports { rpio_02_r }]; #IO_L22P_T3_34 Sch=rpio_02_r
#set_property -dict { PACKAGE_PIN W19 IOSTANDARD LVCMOS33 } [get_ports { rpio_03_r }]; #IO_L22N_T3_34 Sch=rpio_03_r
set_property -dict { PACKAGE_PIN Y18 IOSTANDARD LVCMOS33 } [get_ports { rpio_04_r }]; #IO_L17P_T2_34 Sch=rpio_04_r
set_property -dict { PACKAGE_PIN Y19 IOSTANDARD LVCMOS33 } [get_ports { rpio_05_r }]; #IO_L17N_T2_34 Sch=rpio_05_r
#set_property -dict { PACKAGE_PIN U18 IOSTANDARD LVCMOS33 } [get_ports { rpio_06_r }]; #IO_L22P_T3_13 Sch=rpio_06_r
#set_property -dict { PACKAGE_PIN U19 IOSTANDARD LVCMOS33 } [get_ports { rpio_07_r }]; #IO_L12P_T1_MRCC_34 Sch=rpio_07_r
#set_property -dict { PACKAGE_PIN F19 IOSTANDARD LVCMOS33 } [get_ports { rpio_08_r }]; #IO_L12N_T1_MRCC_34 Sch=rpio_08_r
#set_property -dict { PACKAGE_PIN V10 IOSTANDARD LVCMOS33 } [get_ports { rpio_09_r }]; #IO_L21N_T3_DQS_13 Sch=rpio_09_r
#set_property -dict { PACKAGE_PIN V8 IOSTANDARD LVCMOS33 } [get_ports { rpio_10_r }]; #IO_L15P_T2_DQS_13 Sch=rpio_10_r
#set_property -dict { PACKAGE_PIN W10 IOSTANDARD LVCMOS33 } [get_ports { rpio_11_r }]; #IO_L16P_T2_13 Sch=rpio_11_r
#set_property -dict { PACKAGE_PIN B20 IOSTANDARD LVCMOS33 } [get_ports { rpio_12_r }]; #IO_L1N_T0_AD0N_35 Sch=rpio_12_r
#set_property -dict { PACKAGE_PIN W8 IOSTANDARD LVCMOS33 } [get_ports { rpio_13_r }]; #IO_L15N_T2_DQS_13 Sch=rpio_13_r
#set_property -dict { PACKAGE_PIN V6 IOSTANDARD LVCMOS33 } [get_ports { rpio_14_r }]; #IO_L22P_T3_13 Sch=rpio_14_r
#set_property -dict { PACKAGE_PIN Y6 IOSTANDARD LVCMOS33 } [get_ports { rpio_15_r }]; #IO_L13N_T2_MRCC_13 Sch=rpio_15_r
#set_property -dict { PACKAGE_PIN B19 IOSTANDARD LVCMOS33 } [get_ports { rpio_16_r }]; #IO_L2P_T0_AD8P_35 Sch=rpio_16_r
#set_property -dict { PACKAGE_PIN U7 IOSTANDARD LVCMOS33 } [get_ports { rpio_17_r }]; #IO_L11P_T1_SRCC_13 Sch=rpio_17_r
#set_property -dict { PACKAGE_PIN C20 IOSTANDARD LVCMOS33 } [get_ports { rpio_18_r }]; #IO_L1P_T0_AD0P_35 Sch=rpio_18_r
#set_property -dict { PACKAGE_PIN Y8 IOSTANDARD LVCMOS33 } [get_ports { rpio_19_r }]; #IO_L14N_T2_SRCC_13 Sch=rpio_19_r
#set_property -dict { PACKAGE_PIN A20 IOSTANDARD LVCMOS33 } [get_ports { rpio_20_r }]; #IO_L2N_T0_AD8N_35 Sch=rpio_20_r
#set_property -dict { PACKAGE_PIN Y9 IOSTANDARD LVCMOS33 } [get_ports { rpio_21_r }]; #IO_L14P_T2_SRCC_13 Sch=rpio_21_r
#set_property -dict { PACKAGE_PIN U8 IOSTANDARD LVCMOS33 } [get_ports { rpio_22_r }]; #IO_L17N_T2_13 Sch=rpio_22_r
#set_property -dict { PACKAGE_PIN W6 IOSTANDARD LVCMOS33 } [get_ports { rpio_23_r }]; #IO_IO_L22N_T3_13 Sch=rpio_23_r
#set_property -dict { PACKAGE_PIN Y7 IOSTANDARD LVCMOS33 } [get_ports { rpio_24_r }]; #IO_L13P_T2_MRCC_13 Sch=rpio_24_r
#set_property -dict { PACKAGE_PIN F20 IOSTANDARD LVCMOS33 } [get_ports { rpio_25_r }]; #IO_L15N_T2_DQS_AD12N_35 Sch=rpio_25_r
#set_property -dict { PACKAGE_PIN W9 IOSTANDARD LVCMOS33 } [get_ports { rpio_26_r }]; #IO_L16N_T2_13 Sch=rpio_26_r
#set_property -dict { PACKAGE_PIN Y16 IOSTANDARD LVCMOS33 } [get_ports { rpio_sd_r }]; #IO_L7P_T1_34 Sch=rpio_sd_r
#set_property -dict { PACKAGE_PIN Y17 IOSTANDARD LVCMOS33 } [get_ports { rpio_sc_r }]; #IO_L7N_T1_34 Sch=rpio_sc_r
##HDMI Rx
#set_property -dict { PACKAGE_PIN H17 IOSTANDARD LVCMOS33 } [get_ports { hdmi_rx_cec }]; #IO_L13N_T2_MRCC_35 Sch=hdmi_rx_cec
#set_property -dict { PACKAGE_PIN P19 IOSTANDARD TMDS_33 } [get_ports { hdmi_rx_clk_n }]; #IO_L13N_T2_MRCC_34 Sch=hdmi_rx_clk_n
#set_property -dict { PACKAGE_PIN N18 IOSTANDARD TMDS_33 } [get_ports { hdmi_rx_clk_p }]; #IO_L13P_T2_MRCC_34 Sch=hdmi_rx_clk_p
#set_property -dict { PACKAGE_PIN W20 IOSTANDARD TMDS_33 } [get_ports { hdmi_rx_d_n[0] }]; #IO_L16N_T2_34 Sch=hdmi_rx_d_n[0]
#set_property -dict { PACKAGE_PIN V20 IOSTANDARD TMDS_33 } [get_ports { hdmi_rx_d_p[0] }]; #IO_L16P_T2_34 Sch=hdmi_rx_d_p[0]
#set_property -dict { PACKAGE_PIN U20 IOSTANDARD TMDS_33 } [get_ports { hdmi_rx_d_n[1] }]; #IO_L15N_T2_DQS_34 Sch=hdmi_rx_d_n[1]
#set_property -dict { PACKAGE_PIN T20 IOSTANDARD TMDS_33 } [get_ports { hdmi_rx_d_p[1] }]; #IO_L15P_T2_DQS_34 Sch=hdmi_rx_d_p[1]
#set_property -dict { PACKAGE_PIN P20 IOSTANDARD TMDS_33 } [get_ports { hdmi_rx_d_n[2] }]; #IO_L14N_T2_SRCC_34 Sch=hdmi_rx_d_n[2]
#set_property -dict { PACKAGE_PIN N20 IOSTANDARD TMDS_33 } [get_ports { hdmi_rx_d_p[2] }]; #IO_L14P_T2_SRCC_34 Sch=hdmi_rx_d_p[2]
#set_property -dict { PACKAGE_PIN T19 IOSTANDARD LVCMOS33 } [get_ports { hdmi_rx_hpd }]; #IO_25_34 Sch=hdmi_rx_hpd
#set_property -dict { PACKAGE_PIN U14 IOSTANDARD LVCMOS33 } [get_ports { hdmi_rx_scl }]; #IO_L11P_T1_SRCC_34 Sch=hdmi_rx_scl
#set_property -dict { PACKAGE_PIN U15 IOSTANDARD LVCMOS33 } [get_ports { hdmi_rx_sda }]; #IO_L11N_T1_SRCC_34 Sch=hdmi_rx_sda
##HDMI Tx
#set_property -dict { PACKAGE_PIN G15 IOSTANDARD LVCMOS33 } [get_ports { hdmi_tx_cec }]; #IO_L19N_T3_VREF_35 Sch=hdmi_tx_cec
#set_property -dict { PACKAGE_PIN L17 IOSTANDARD TMDS_33 } [get_ports { hdmi_tx_clk_n }]; #IO_L11N_T1_SRCC_35 Sch=hdmi_tx_clk_n
#set_property -dict { PACKAGE_PIN L16 IOSTANDARD TMDS_33 } [get_ports { hdmi_tx_clk_p }]; #IO_L11P_T1_SRCC_35 Sch=hdmi_tx_clk_p
#set_property -dict { PACKAGE_PIN K18 IOSTANDARD TMDS_33 } [get_ports { hdmi_tx_d_n[0] }]; #IO_L12N_T1_MRCC_35 Sch=hdmi_tx_d_n[0]
#set_property -dict { PACKAGE_PIN K17 IOSTANDARD TMDS_33 } [get_ports { hdmi_tx_d_p[0] }]; #IO_L12P_T1_MRCC_35 Sch=hdmi_tx_d_p[0]
#set_property -dict { PACKAGE_PIN J19 IOSTANDARD TMDS_33 } [get_ports { hdmi_tx_d_n[1] }]; #IO_L10N_T1_AD11N_35 Sch=hdmi_tx_d_n[1]
#set_property -dict { PACKAGE_PIN K19 IOSTANDARD TMDS_33 } [get_ports { hdmi_tx_d_p[1] }]; #IO_L10P_T1_AD11P_35 Sch=hdmi_tx_d_p[1]
#set_property -dict { PACKAGE_PIN H18 IOSTANDARD TMDS_33 } [get_ports { hdmi_tx_d_n[2] }]; #IO_L14N_T2_AD4N_SRCC_35 Sch=hdmi_tx_d_n[2]
#set_property -dict { PACKAGE_PIN J18 IOSTANDARD TMDS_33 } [get_ports { hdmi_tx_d_p[2] }]; #IO_L14P_T2_AD4P_SRCC_35 Sch=hdmi_tx_d_p[2]
#set_property -dict { PACKAGE_PIN R19 IOSTANDARD LVCMOS33 } [get_ports { hdmi_tx_hpdn }]; #IO_0_34 Sch=hdmi_tx_hpdn
##Crypto SDA
#set_property -dict { PACKAGE_PIN J15 IOSTANDARD LVCMOS33 } [get_ports { crypto_sda }]; #IO_25_35 Sch=crypto_sda
到了这里,关于pynq z2约束文件的文章就介绍完了。如果您还想了解更多内容,请在右上角搜索TOY模板网以前的文章或继续浏览下面的相关文章,希望大家以后多多支持TOY模板网!