网络拓扑图
文章来源地址https://www.toymoban.com/news/detail-658722.html
拓扑说明
用户路由器用于模拟家用拨号路由器,该设备为pppoe的客户端
电信ISP设备则模拟电信的网络设备,该设备为pppoe的服务端
而中间交换机则用于模拟光猫;光猫为桥接模式,此处不做任何配置,当场傻瓜式设备使用
电信ISP设备配置
<Huawei>system-view # 进入系统视图
[Huawei]sysname ISP # 配置路由器名字
[ISP]aaa
[ISP-aaa]local-user huawei password cipher huawei
[ISP-aaa]local-user huawei service-type ppp
[ISP-aaa]quit
[ISP]ip pool pppoe
[ISP-ip-pool-pppoe]network 100.64.254.0 mask 24
[ISP-ip-pool-pppoe]gateway-list 100.64.254.1
[ISP-ip-pool-pppoe]dns-list 114.114.114.114 223.5.5.5
[ISP-ip-pool-pppoe]quit
[ISP]interface Virtual-Template 1
[ISP-Virtual-Template1]ip address 100.64.254.1 24
[ISP-Virtual-Template1]remote address pool pppoe
[ISP-Virtual-Template1]ppp authentication-mode chap
[ISP]interface GigabitEthernet 0/0/0
[ISP-GigabitEthernet0/0/0]pppoe-server bind virtual-template 1
用户拨号路由器配置
dialer-rule
dialer-rule 1 ip permit
interface Dialer1
link-protocol ppp
ppp chap user huawei
ppp chap password cipher %$%$gu>xPdzPz>"FWUHp:EdW,"%o%$%$
ppp pap local-user huawei password cipher %$%$0VL)HZ/u8~H>]sNN#yiY,"K\%$%$
ip address ppp-negotiate
dialer user HUAWEI
dialer bundle 1
dialer-group 1
nat outbound 3000
acl number 3000
rule 100 permit ip
interface GigabitEthernet0/0/0
pppoe-client dial-bundle-number 1
查看是否拨上号
[jiucai]display ip interface brief
Interface IP Address/Mask Physical Protocol
Dialer1 100.64.254.254/32 up up(s)
GigabitEthernet0/0/0 unassigned up down
[jiucai]ping 100.64.254.1
PING 100.64.254.1: 56 data bytes, press CTRL_C to break
Reply from 100.64.254.1: bytes=56 Sequence=1 ttl=255 time=80 ms
Reply from 100.64.254.1: bytes=56 Sequence=2 ttl=255 time=50 ms
Reply from 100.64.254.1: bytes=56 Sequence=3 ttl=255 time=20 ms
Reply from 100.64.254.1: bytes=56 Sequence=4 ttl=255 time=30 ms
--- 100.64.254.1 ping statistics ---
4 packet(s) transmitted
4 packet(s) received
0.00% packet loss
round-trip min/avg/max = 20/45/80 ms
[jiucai]display dialer interface Dialer 1
Dial Interface:Dialer1
Dialer Timers(Secs):
Auto-dial:300 Compete:20 Enable:5
Idle:120 Wait-for-Carrier:60
[jiucai]display interface Dialer 1
Dialer1 current state : UP
Line protocol current state : UP (spoofing)
Description:HUAWEI, AR Series, Dialer1 Interface
Route Port,The Maximum Transmit Unit is 1500, Hold timer is 10(sec)
Internet Address is negotiated, 100.64.254.254/32
Link layer protocol is PPP
LCP initial
Physical is Dialer
Current system time: 2023-08-18 14:48:11-08:00
Last 300 seconds input rate 0 bits/sec, 0 packets/sec
Last 300 seconds output rate 0 bits/sec, 0 packets/sec
Realtime 0 seconds input rate 0 bits/sec, 0 packets/sec
Realtime 0 seconds output rate 0 bits/sec, 0 packets/sec
Input: 0 bytes
Output:0 bytes
Input bandwidth utilization : 0%
Output bandwidth utilization : 0%
Bound to Dialer1:0:
Dialer1:0 current state : UP ,
Line protocol current state : UP
Link layer protocol is PPP
LCP opened, IPCP opened
Packets statistics:
Input packets:0, 0 bytes
Output packets:4, 336 bytes
FCS error packets:0
Address error packets:0
Control field control error packets:0
是否看不懂? 看不懂就对了,只是记录一下命令。至于所有原理,等想写了再写
文章来源:https://www.toymoban.com/news/detail-658722.html
到了这里,关于华为PPPOE配置实验的文章就介绍完了。如果您还想了解更多内容,请在右上角搜索TOY模板网以前的文章或继续浏览下面的相关文章,希望大家以后多多支持TOY模板网!