1、准备材料
开发板（正点原子stm32f407探索者开发板V2.4）
STM32CubeMX软件（Version 6.10.0）
野火DAP仿真器
keil µVision5 IDE（MDK-Arm）
ST-LINK/V2驱动
XCOM V2.6串口助手
2、实验目标
使用STM32CubeMX软件配置STM32F407开发板FSMC接口驱动8080并行接口TFT-LCD显示，具体为使用FSMC Bank 1-NOR/PSRAM4，片选信号为NE4（PG12），TFT-LCD的RS引脚接FSMC地址线A6（PF12）来驱动TFT-LCD进行不同颜色刷屏显示
3、实验流程
3.0、前提知识
开发板使用TFT-LCD时最好使用外接电源给开发板供电，如果使用单USB供电可能会出现电流不足电压波动TFT-LCD初始化失败的现象，以下TFT-LCD全部简称为LCD
3.0.0、FSMC概述
FSMC全称为灵活的静态存储控制器，其时钟信号为HCLK，FSMC根据支持的存储器类型可以分为NOR/PSRAM、NAND Flash和PC卡三种，本实验只涉及第一种NOR/PSRAM，严格意义上讲也与NOR/PSRAM无关，只是使用其中的LCD Interface类型的内存类型，下图中2号红框中标出了本此实验需要使用的FSMC的一些引脚，主要包括片选引脚、地址线、数据线、输出和写入等，如下图所示为FSMC的具体框图 （注释1）
从FSMC的角度，外部存储器被划分为4个固定大小的存储区域，每个存储区域的大小为256 MB，存储区域1可连接4个NOR Flash或PSRAM存储器器件，此存储区域被划分为4个NOR/PSRAM区域，带4个专用片选信号NE1/2/3/4，每个区域大小为64MB，FSMC的具体存储区域映射如下图所示
通过FSMC写入外部存储设备需要知道写入的地址，该地址有HADDR所确定，HADDR是AHB内部地址线，但也会参与对外部存储器的寻址，其HADDR[27:26]两个位用于选择从地址0X6000 0000到地址0x6FFF FFFF处分成4个部分的存储区域，HADDR[25:0]的26个位用于地址线，确定写入选中存储区域中的地址，如下图所示位HADDR的解释 （注释2）
由于 HADDR 为字节地址，而存储器按字寻址，据存储器数据宽度不同，实际向存储器发送的地址也将有所不同，当存储器宽度为16位（16根数据线）时，向存储器发出的数据地址将自动向右偏移一位，具体如下表所
3.0.1、为什么使用FSMC控制LCD?
FSMC一般是用来连接SRAM、PSRAM、ROM和NOR Flash等存储设备的，为什么要使用FSMC来控制8080并口的LCD呢？
先来看一看这些存储设备和8080并口LCD的引脚，SRAM的接口如下图所示 （注释3）
8080并口LCD的接口引脚如下图所示
可以发现LCD的接口中除去RST和背光BLK引脚外，其他的引脚均可以由FSMC来提供，RS引脚可以选择FSMC的26位地址线中的一根控制，片选信号可以由FSMC的NEx引脚提供，RD由NOE提供，WR由NWE提供，D0-D15可以与FSMC的16跟数据线直接连接
所以在FSMC的NORFIash/PSRAM/SRAM/ROM/LCDx中也有一个专门的LCD Interface类型的内存类型，因此我们其实可以把8080并口的LCD当成一个存储设备通过FSMC来控制
3.0.2、LCD接口硬件原理详解
如下图所示为LCD接口硬件原理图
- 8080并口LCD的片选信号CS可以直接使用FSMC的NEx引脚，这里使用FSMC Bank 1-NOR/PSRAM4来控制LCD，因此CS接FSMC_NE4
- LCD写入引脚WR接FSMC的写入使能引脚FSMC_NWE
- LCD的读操作引脚接FSMC的输出使能引脚FSMC_NOE
- LCD寄存器选择引脚RS接26位地址线上任何一根都可以，这里接入了A6
- 16位数据线直接对接
- LCD的复位引脚与开发板复位引脚相连，使用开发板复位引脚可以同时复位MCU和LCD
- LCD的背光引脚由PB15引脚控制，当高电平时背光被点亮
3.0.3、控制FSMC对LCD命令/数据写入（重点）
使用FSMC写LCD时一般分为写数据（选择数据寄存器）或者写命令（选择控制寄存器），而LCD的RS引脚负责决定选择数据还是控制寄存器，如果RS引脚是高电平1，则选择数据寄存器；如果RS引脚引脚为低电平0，则选择控制寄存器
FSMC的地址线一共有26位（FSMC_A[25:0]），对于LCD来说，只需要任选其中一根地址线与RS引脚连接即可实现对LCD写数据/命令的控制，但是选择不同地址线所对应的控制写命令/数据的地址也不相同
以本实验为例，此时LCD使用FSMC Bank 1-NOR/PSRAM4，其起始地址为0x6C00 0000，LCD的RS引脚接FSMC地址线A6（PF12），且此时LCD为16位宽度数据传输，FSMC会将写入的地址自动向右偏移一位，因此LCD的RS引脚选择控制寄存器只需要在起始地址基础上满足A7位为0即可，比如可以是0x6C00 0000，也可以是0x6C00 0040等；LCD的RS引脚选择写数据寄存器只需要在起始地址基础上满足A7位为1即可，比如可以是0x6C00 0080，也可以是0x6C00 00C0等；
因此我们可以直接定义FSMC写LCD命令/数据的地址，第一种方法源代码如下所示
/*LCD写命令地址*/
#define LCD_REG (*((volatile unsigned short *) 0x6C000000))
/*LCD写数据地址*/
#define LCD_RAM (*((volatile unsigned short *) 0x6C000080))
/*将数据data写入LCD数据寄存器*/
LCD_RAM = data;
/*将寄存器值regval写入LCD控制寄存器*/
LCD_REG = regval;
除了上述的方法外，常见的还有一种定义LCD地址结构体的方法，其原理一致，但读者理解的时候可能不太容易理解，接下来由笔者仔细分析一下，第二种方法源代码如下所示
/*定义LCD地址结构体*/
typedef struct
{
volatile uint16_t LCD_REG;
volatile uint16_t LCD_RAM;
}LCD_TypeDef;
/*LCD控制/数据寄存器基址*/
#define LCD_BASE ((uint32_t)(0x6C000000 | 0x0000007E))
#define LCD ((LCD_TypeDef *) LCD_BASE)
/*将数据data写入LCD数据寄存器*/
LCD->LCD_RAM=data;
/*将寄存器值regval写入LCD控制寄存器*/
LCD->LCD_REG=regval;
我们已经知道，当LCD的RS引脚接FSMC地址线A6，由于FSMC会将写入的地址自动向右偏移一位，因此写入数据（选择数据寄存器）时地址线A7应该为1，写入命令（选择控制寄存器）时地址线A7应该为0
而在结构体中先定义了uint16_t（2个字节）的LCD_REG变量，紧接着定义了uint16_t的LCD_RAM变量，这两个变量在内存中的地址应该是连续的
并且我们将LCD变量强制转化为了LCD_TypeDef*类型的变量，同时将LCD_BASE的地址赋值给LCD，因此LCD的地址应该为(0x6C000000 | 0x0000007E))，LCD->LCD_REG的地址应该同样为(0x6C000000 | 0x0000007E))，而LCD->LCD_RAM的地址应该为(0x6C000000 | 0x0000007E+2))
此时读者应该可以发现通过结构体中顺序定义的变量在内存中地址连续这一特点，LCD->LCD_REG表示了地址线A7为0，LCD->LCD_RAM表示了地址线A7为1，也即通过LCD->LCD_REG可以写入LCD命令，通过LCD->LCD_RAM可以写入LCD数据
再举个例子，如果LCD的RS引脚接FSMC地址线的A12呢？
此时写入数据（选择数据寄存器）时地址线A13应该为1，写入命令（选择控制寄存器）时地址线A13应该为0
则按照第一种方法，可定义为如下代码
/*LCD写命令地址*/
#define LCD_REG (*((volatile unsigned short *) 0x6C000000))
/*LCD写数据地址*/
#define LCD_RAM (*((volatile unsigned short *) 0x60002000))
按照第二种方法，可定义为如下代码
/*LCD控制/数据寄存器基址*/
#define LCD_BASE ((uint32_t)(0x6C000000 | 0x00001FFE))
#define LCD ((LCD_TypeDef *) LCD_BASE)
一个小技巧，在使用第二种方法确定 LCD_BASE 地址时，假如RS接FSMC的地址线A6，则从右边往左数到A7位（中间全是1，两边两个0），0111 1110（0x7E）；假如RS接FSMC的地址线A12，同样从右边往左数到A13位，01 1111 1111 1110（0x1FFE）；
3.0.4、FSMC时序参数设置
查看LCD使用的控制芯片NT35510的芯片数据手册 （注释4）
在361页的7.6.1并行接口特性（80 系列 MCU）小节中说明了使用8080并行接口控制的LCD所需要满足的时序和信号特征的最大最小值
如下图中表格所示，重点看表格中读写的地址建立时间和数据建立时间，其规定了最小需要的时间
在STM32CubeMX中可以设置读写时序的地址建立时间和数据建立时间，单位为一个HCLK时钟周期，当HCLK时钟频率为STM32F407最高频率168MHz时，一个周期大约为6us
这里按照手册理论上读地址建立时间>10ns（2个HCLK时钟周期），写地址建立时间>0us，数据建立/保持时间>15+10ns（5个HCLK时钟周期），读写地址保持时间>2ns，但生成代码中读写地址保持时间默认15个HCLK时钟周期，在软件上不可调，另外总线翻转时间设置为0，访问模式选择A即可
因此综上所述，将参数从上到下设置为2、5、0、A、0、5、0和A（笔者在正点原子探索者开发板上使用4.3寸NT35510控制的LCD上验证可以使用），实际使用中如果出现问题可以增大参数值，具体配置如下图所示
再举个例子，如果你的LCD使用的控制芯片为ILI9341，那么找到ILI9341芯片数据手册 （注释5）
在手册238页18.3.1小节中找到8080并口控制时的时序参数要求，如下图所示，根据手册我们可以知道理论上读/写地址建立时间>0ns，数据建立/保持时间>10+10ns（4个HCLK时钟周期），读写地址保持时间>0ns
因此在STM32CubeMX中参数从上到下设置为0、4、0、A、0、4、0和A即可（笔者在正点原子探索者开发板上使用野火3.2寸ILI9341控制的LCD上验证可以使用）
3.1、CubeMX相关配置
3.1.0、工程基本配置
打开STM32CubeMX软件，单击ACCESS TO MCU SELECTOR选择开发板MCU（选择你使用开发板的主控MCU型号）选中MCU型号后单击页面右上角Start Project开始工程，具体如下图所示
开始工程之后在配置主页面System Core/RCC中配置HSE/LSE晶振，在System Core/SYS中配置Debug模式，具体如下图所示
详细工程建立内容读者可以阅读“STM32CubeMX教程1 工程建立”
3.1.1、时钟树配置
系统时钟使用8MHz外部高速时钟HSE，HCLK、PCLK1和PCLK2均设置为STM32F407能达到的最高时钟频率，具体如下图所示
3.1.2、外设参数配置
单击Pinout & Configuration页面左边Connectivity/FSMC选项，在右边的Mode下点开NORFIash/PSRAM/SRAM/ROM/LCD4选项卡（因为LCD使用的是使用FSMC Bank 1-NOR/PSRAM4），选择片选信号NE4，内存类型为LCD Interface，LCD寄存器选择（RS引脚）选择FSMC地址线A6，数据Data为16位（D0-D15），具体配置如下图所示
然后在Configuration里面配置其读写时序，为什么要这样配置？可以阅读本实验“3.0.4、时序参数设置”小节，具体配置如下图所示
配置好之后可以与硬件原理图上的引脚对照以下，看看有没有漏掉哪些引脚或者那些引脚默认配置不正确，由于RESET引脚直接与MCU的NRST引脚连接，当按下开发板复位按键时，LCD也会被复位，因此最后只需设置LCD的背光控制引脚即可，具体配置如下图所示
3.1.3、外设中断配置
本实验无需配置任何中断
3.2、生成代码
3.2.0、配置Project Manager页面
单击进入Project Manager页面，在左边Project分栏中修改工程名称、工程目录和工具链，然后在Code Generator中勾选“Gnerate peripheral initialization as a pair of 'c/h' files per peripheral”，最后单击页面右上角GENERATE CODE生成工程，具体如下图所示
详细Project Manager配置内容读者可以阅读“STM32CubeMX教程1 工程建立”实验3.4.3小节
3.2.1、外设初始化调用流程
在STM32CubeMX中配置了FSMC之后，会在生成的工程代码中新增MX_FSMC_Init()函数，在该函数中对FSMC的模式和对FSMC的读写时序参数进行了配置，然后调用了HAL_SRAM_Init()初始化函数
在HAL_SRAM_Init()初始化函数中调用了HAL_SRAM_MspInit()，然后在HAL_SRAM_MspInit()函数中最终调用了HAL_FSMC_MspInit()
在HAL_FSMC_MspInit()函数中完成了FSMC的数据线、地址线、读和写等引脚的复用操作，并且使能了相应的时钟
如下图所示为FSMC初始化具体调用流程
3.2.2、外设中断调用流程
本实验无需配置任何中断
3.2.3、添加其他必要代码
首先需要添加LCD的驱动文件，该驱动文件中应该对LCD进行正常初始化操作，另外应该包含一些LCD的画图函数，比如绘制圆形、直线和矩形等函数，一般是按照LCD驱动芯片的手册进行编程，但是为了避免重复造轮子，这里的驱动文件直接使用正点原子提供的 （注释6），笔者对文件稍微整理了以下，具体源代码如下所示
tftlcd.c文件
点击查看代码
#include "tftlcd.h"
#include "stdlib.h"
#include "font.h"
#include "stdio.h"
//
//本程序只供学习使用，未经作者许可，不得用于其它任何用途
//ALIENTEK STM32开发板
//2.8寸/3.5寸/4.3寸/7寸 TFT液晶驱动
//支持驱动IC型号包括:ILI9341/NT35310/NT35510/SSD1963等
//正点原子@ALIENTEK
//技术论坛:www.openedv.com
//创建日期:2017/4/8
//版本：V4.0
//版权所有，盗版必究。
//Copyright(C) 广州市星翼电子科技有限公司 2014-2024
//All rights reserved
//*******************************************************************************
//V4.0 20211111
//1，去掉大部分不常用驱动IC的支持
//2，新增对ST7789驱动IC的支持
//3，优化代码结构（精简源码）
//
//LCD的画笔颜色和背景色
uint32_t POINT_COLOR=0xFF000000; //画笔颜色
uint32_t BACK_COLOR =0xFFFFFFFF; //背景色
//管理LCD重要参数
//默认为竖屏
_lcd_dev lcddev;
//MCU频率为168MHz时的us延时
void delay_us(uint32_t nus)
{
uint32_t Delay = nus * 168/4;
do
{
__NOP();
}
while (Delay --);
}
//写寄存器函数
//regval:寄存器值
void LCD_WR_REG(volatile uint16_t regval)
{
regval=regval; //使用-O2优化的时候,必须插入的延时
LCD->LCD_REG=regval; //写入要写的寄存器序号
}
//写LCD数据
//data:要写入的值
void LCD_WR_DATA(volatile uint16_t data)
{
data=data; //使用-O2优化的时候,必须插入的延时
LCD->LCD_RAM=data;
}
//读LCD数据
//返回值:读到的值
uint16_t LCD_RD_DATA(void)
{
volatile uint16_t ram; //防止被优化
ram=LCD->LCD_RAM;
return ram;
}
//写寄存器
//LCD_Reg:寄存器地址
//LCD_RegValue:要写入的数据
void LCD_WriteReg(uint16_t LCD_Reg,uint16_t LCD_RegValue)
{
LCD->LCD_REG = LCD_Reg; //写入要写的寄存器序号
LCD->LCD_RAM = LCD_RegValue;//写入数据
}
//读寄存器
//LCD_Reg:寄存器地址
//返回值:读到的数据
uint16_t LCD_ReadReg(uint16_t LCD_Reg)
{
LCD_WR_REG(LCD_Reg); //写入要读的寄存器序号
delay_us(5);
return LCD_RD_DATA(); //返回读到的值
}
//开始写GRAM
void LCD_WriteRAM_Prepare(void)
{
LCD->LCD_REG=lcddev.wramcmd;
}
//LCD写GRAM
//RGB_Code:颜色值
void LCD_WriteRAM(uint16_t RGB_Code)
{
LCD->LCD_RAM = RGB_Code; //写十六位GRAM
}
//从ILI93xx读出的数据为GBR格式，而我们写入的时候为RGB格式。
//通过该函数转换
//c:GBR格式的颜色值
//返回值：RGB格式的颜色值
uint16_t LCD_BGR2RGB(uint16_t c)
{
uint16_t r,g,b,rgb;
b=(c>>0)&0x1f;
g=(c>>5)&0x3f;
r=(c>>11)&0x1f;
rgb=(b<<11)+(g<<5)+(r<<0);
return(rgb);
}
//当mdk -O1时间优化时需要设置
//延时i
void opt_delay(uint8_t i)
{
while(i--);
}
//读取个某点的颜色值
//x,y:坐标
//返回值:此点的颜色
uint32_t LCD_ReadPoint(uint16_t x,uint16_t y)
{
uint16_t r=0,g=0,b=0;
if(x>=lcddev.width||y>=lcddev.height)return 0; //超过了范围,直接返回
LCD_SetCursor(x,y);
if (lcddev.id == 0X5510) //5510 发送读GRAM指令
{
LCD_WR_REG(0X2E00);
}
else //其他IC(9341/5310/1963/7789)发送读GRAM指令
{
LCD_WR_REG(0X2E);
}
r=LCD_RD_DATA(); //dummy Read
if (lcddev.id == 0X1963) //对1963来说,是真读
{
return r; //1963直接读就可以
}
opt_delay(2);
r = LCD_RD_DATA(); //实际坐标颜色
//9341/5310/5510/7789 要分2次读出
opt_delay(2);
b = LCD_RD_DATA();
g = r & 0XFF; //对于9341/5310/5510/7789, 第一次读取的是RG的值,R在前,G在后,各占8位
g <<= 8; //9341/5310/5510/7789 需要公式转换一下
return (((r >> 11) << 11) | ((g >> 10) << 5) | (b >> 11));
}
//LCD开启显示
void LCD_DisplayOn(void)
{
if (lcddev.id == 0X5510) //5510开启显示指令
{
LCD_WR_REG(0X2900); //开启显示
}
else //9341/5310/1963/7789 等发送开启显示指令
{
LCD_WR_REG(0X29); //开启显示
}
}
//LCD关闭显示
void LCD_DisplayOff(void)
{
if (lcddev.id == 0X5510) //5510关闭显示指令
{
LCD_WR_REG(0X2800); //关闭显示
}
else //9341/5310/1963/7789 等发送关闭显示指令
{
LCD_WR_REG(0X28); //关闭显示
}
}
//设置光标位置
//Xpos:横坐标
//Ypos:纵坐标
void LCD_SetCursor(uint16_t Xpos, uint16_t Ypos)
{
if (lcddev.id == 0X1963)
{
if (lcddev.dir == 0) //x坐标需要变换
{
Xpos = lcddev.width - 1 - Xpos;
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(0);
LCD_WR_DATA(0);
LCD_WR_DATA(Xpos >> 8);
LCD_WR_DATA(Xpos & 0XFF);
}
else
{
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(Xpos >> 8);
LCD_WR_DATA(Xpos & 0XFF);
LCD_WR_DATA((lcddev.width - 1) >> 8);
LCD_WR_DATA((lcddev.width - 1) & 0XFF);
}
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(Ypos >> 8);
LCD_WR_DATA(Ypos & 0XFF);
LCD_WR_DATA((lcddev.height - 1) >> 8);
LCD_WR_DATA((lcddev.height - 1) & 0XFF);
}
else if (lcddev.id == 0X5510)
{
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(Xpos >> 8);
LCD_WR_REG(lcddev.setxcmd + 1);
LCD_WR_DATA(Xpos & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(Ypos >> 8);
LCD_WR_REG(lcddev.setycmd + 1);
LCD_WR_DATA(Ypos & 0XFF);
}
else //9341/5310/7789等设置坐标
{
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(Xpos >> 8);
LCD_WR_DATA(Xpos & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(Ypos >> 8);
LCD_WR_DATA(Ypos & 0XFF);
}
}
//设置LCD的自动扫描方向
//dir:0~7,代表8个方向(具体定义见lcd.h)
//9341/5310/5510/1963/7789等IC已经实际测试
//注意:其他函数可能会受到此函数设置的影响(尤其是9341),
//所以,一般设置为L2R_U2D即可,如果设置为其他扫描方式,可能导致显示不正常.
void LCD_Scan_Dir(uint8_t dir)
{
uint16_t regval=0;
uint16_t dirreg=0;
uint16_t temp;
//横屏时，对1963不改变扫描方向, 其他IC改变扫描方向！竖屏时1963改变方向, 其他IC不改变扫描方向
if ((lcddev.dir == 1 && lcddev.id != 0X1963) || (lcddev.dir == 0 && lcddev.id == 0X1963))
{
switch (dir) //方向转换
{
case 0:
dir = 6;
break;
case 1:
dir = 7;
break;
case 2:
dir = 4;
break;
case 3:
dir = 5;
break;
case 4:
dir = 1;
break;
case 5:
dir = 0;
break;
case 6:
dir = 3;
break;
case 7:
dir = 2;
break;
}
}
switch (dir)
{
case L2R_U2D://从左到右,从上到下
regval |= (0 << 7) | (0 << 6) | (0 << 5);
break;
case L2R_D2U://从左到右,从下到上
regval |= (1 << 7) | (0 << 6) | (0 << 5);
break;
case R2L_U2D://从右到左,从上到下
regval |= (0 << 7) | (1 << 6) | (0 << 5);
break;
case R2L_D2U://从右到左,从下到上
regval |= (1 << 7) | (1 << 6) | (0 << 5);
break;
case U2D_L2R://从上到下,从左到右
regval |= (0 << 7) | (0 << 6) | (1 << 5);
break;
case U2D_R2L://从上到下,从右到左
regval |= (0 << 7) | (1 << 6) | (1 << 5);
break;
case D2U_L2R://从下到上,从左到右
regval |= (1 << 7) | (0 << 6) | (1 << 5);
break;
case D2U_R2L://从下到上,从右到左
regval |= (1 << 7) | (1 << 6) | (1 << 5);
break;
}
if (lcddev.id == 0X5510)dirreg = 0X3600;
else dirreg = 0X36;
if (lcddev.id == 0X9341 || lcddev.id == 0X7789) //9341 & 7789 要设置BGR位
{
regval |= 0X08;
}
LCD_WriteReg(dirreg, regval);
if (lcddev.id != 0X1963) //1963不做坐标处理
{
if (regval & 0X20)
{
if (lcddev.width < lcddev.height) //交换X,Y
{
temp = lcddev.width;
lcddev.width = lcddev.height;
lcddev.height = temp;
}
}
else
{
if (lcddev.width > lcddev.height) //交换X,Y
{
temp = lcddev.width;
lcddev.width = lcddev.height;
lcddev.height = temp;
}
}
}
//设置显示区域(开窗)大小
if (lcddev.id == 0X5510)
{
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(0);
LCD_WR_REG(lcddev.setxcmd + 1);
LCD_WR_DATA(0);
LCD_WR_REG(lcddev.setxcmd + 2);
LCD_WR_DATA((lcddev.width - 1) >> 8);
LCD_WR_REG(lcddev.setxcmd + 3);
LCD_WR_DATA((lcddev.width - 1) & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(0);
LCD_WR_REG(lcddev.setycmd + 1);
LCD_WR_DATA(0);
LCD_WR_REG(lcddev.setycmd + 2);
LCD_WR_DATA((lcddev.height - 1) >> 8);
LCD_WR_REG(lcddev.setycmd + 3);
LCD_WR_DATA((lcddev.height - 1) & 0XFF);
}
else
{
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(0);
LCD_WR_DATA(0);
LCD_WR_DATA((lcddev.width - 1) >> 8);
LCD_WR_DATA((lcddev.width - 1) & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(0);
LCD_WR_DATA(0);
LCD_WR_DATA((lcddev.height - 1) >> 8);
LCD_WR_DATA((lcddev.height - 1) & 0XFF);
}
}
//画点
//x,y:坐标
//POINT_COLOR:此点的颜色
void LCD_DrawPoint(uint16_t x,uint16_t y)
{
LCD_SetCursor(x,y); //设置光标位置
LCD_WriteRAM_Prepare(); //开始写入GRAM
LCD->LCD_RAM=POINT_COLOR;
}
//快速画点
//x,y:坐标
//color:颜色
void LCD_Fast_DrawPoint(uint16_t x,uint16_t y,uint32_t color)
{
if (lcddev.id == 0X5510)
{
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(x >> 8);
LCD_WR_REG(lcddev.setxcmd + 1);
LCD_WR_DATA(x & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(y >> 8);
LCD_WR_REG(lcddev.setycmd + 1);
LCD_WR_DATA(y & 0XFF);
}
else if (lcddev.id == 0X1963)
{
if (lcddev.dir == 0)x = lcddev.width - 1 - x;
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(x >> 8);
LCD_WR_DATA(x & 0XFF);
LCD_WR_DATA(x >> 8);
LCD_WR_DATA(x & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(y >> 8);
LCD_WR_DATA(y & 0XFF);
LCD_WR_DATA(y >> 8);
LCD_WR_DATA(y & 0XFF);
}
else //9341/5310/7789等设置坐标
{
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(x >> 8);
LCD_WR_DATA(x & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(y >> 8);
LCD_WR_DATA(y & 0XFF);
}
LCD->LCD_REG=lcddev.wramcmd;
LCD->LCD_RAM=color;
}
//SSD1963 背光设置
//pwm:背光等级,0~100.越大越亮.
void LCD_SSD_BackLightSet(uint8_t pwm)
{
LCD_WR_REG(0xBE); //配置PWM输出
LCD_WR_DATA(0x05); //1设置PWM频率
LCD_WR_DATA(pwm*2.55); //2设置PWM占空比
LCD_WR_DATA(0x01); //3设置C
LCD_WR_DATA(0xFF); //4设置D
LCD_WR_DATA(0x00); //5设置E
LCD_WR_DATA(0x00); //6设置F
}
//设置LCD显示方向
//dir:0,竖屏；1,横屏
void LCD_Display_Dir(uint8_t dir)
{
lcddev.dir = dir; //竖屏/横屏
if (dir == 0) //竖屏
{
lcddev.width = 240;
lcddev.height = 320;
if (lcddev.id == 0x5510)
{
lcddev.wramcmd = 0X2C00;
lcddev.setxcmd = 0X2A00;
lcddev.setycmd = 0X2B00;
lcddev.width = 480;
lcddev.height = 800;
}
else if (lcddev.id == 0X1963)
{
lcddev.wramcmd = 0X2C; //设置写入GRAM的指令
lcddev.setxcmd = 0X2B; //设置写X坐标指令
lcddev.setycmd = 0X2A; //设置写Y坐标指令
lcddev.width = 480; //设置宽度480
lcddev.height = 800; //设置高度800
}
else //其他IC, 包括: 9341 / 5310 / 7789等IC
{
lcddev.wramcmd = 0X2C;
lcddev.setxcmd = 0X2A;
lcddev.setycmd = 0X2B;
}
if (lcddev.id == 0X5310) //如果是5310 则表示是 320*480分辨率
{
lcddev.width = 320;
lcddev.height = 480;
}
}
else //横屏
{
lcddev.width = 320;
lcddev.height = 240;
if (lcddev.id == 0x5510)
{
lcddev.wramcmd = 0X2C00;
lcddev.setxcmd = 0X2A00;
lcddev.setycmd = 0X2B00;
lcddev.width = 800;
lcddev.height = 480;
}
else if (lcddev.id == 0X1963)
{
lcddev.wramcmd = 0X2C; //设置写入GRAM的指令
lcddev.setxcmd = 0X2A; //设置写X坐标指令
lcddev.setycmd = 0X2B; //设置写Y坐标指令
lcddev.width = 800; //设置宽度800
lcddev.height = 480; //设置高度480
}
else //其他IC, 包括: 9341 / 5310 / 7789等IC
{
lcddev.wramcmd = 0X2C;
lcddev.setxcmd = 0X2A;
lcddev.setycmd = 0X2B;
}
if (lcddev.id == 0X5310) //如果是5310 则表示是 320*480分辨率
{
lcddev.width = 480;
lcddev.height = 320;
}
}
LCD_Scan_Dir(DFT_SCAN_DIR); //默认扫描方向
}
//设置窗口,并自动设置画点坐标到窗口左上角(sx,sy).
//sx,sy:窗口起始坐标(左上角)
//width,height:窗口宽度和高度,必须大于0!!
//窗体大小:width*height.
void LCD_Set_Window(uint16_t sx, uint16_t sy, uint16_t width, uint16_t height)
{
uint16_t twidth, theight;
twidth = sx + width - 1;
theight = sy + height - 1;
if (lcddev.id == 0X1963 && lcddev.dir != 1) //1963竖屏特殊处理
{
sx = lcddev.width - width - sx;
height = sy + height - 1;
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(sx >> 8);
LCD_WR_DATA(sx & 0XFF);
LCD_WR_DATA((sx + width - 1) >> 8);
LCD_WR_DATA((sx + width - 1) & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(sy >> 8);
LCD_WR_DATA(sy & 0XFF);
LCD_WR_DATA(height >> 8);
LCD_WR_DATA(height & 0XFF);
}
else if (lcddev.id == 0X5510)
{
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(sx >> 8);
LCD_WR_REG(lcddev.setxcmd + 1);
LCD_WR_DATA(sx & 0XFF);
LCD_WR_REG(lcddev.setxcmd + 2);
LCD_WR_DATA(twidth >> 8);
LCD_WR_REG(lcddev.setxcmd + 3);
LCD_WR_DATA(twidth & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(sy >> 8);
LCD_WR_REG(lcddev.setycmd + 1);
LCD_WR_DATA(sy & 0XFF);
LCD_WR_REG(lcddev.setycmd + 2);
LCD_WR_DATA(theight >> 8);
LCD_WR_REG(lcddev.setycmd + 3);
LCD_WR_DATA(theight & 0XFF);
}
else //9341/5310/7789/1963横屏 等 设置窗口
{
LCD_WR_REG(lcddev.setxcmd);
LCD_WR_DATA(sx >> 8);
LCD_WR_DATA(sx & 0XFF);
LCD_WR_DATA(twidth >> 8);
LCD_WR_DATA(twidth & 0XFF);
LCD_WR_REG(lcddev.setycmd);
LCD_WR_DATA(sy >> 8);
LCD_WR_DATA(sy & 0XFF);
LCD_WR_DATA(theight >> 8);
LCD_WR_DATA(theight & 0XFF);
}
}
//初始化lcd
//该初始化函数可以初始化各种ILI93XX液晶,但是其他函数是基于ILI9320的!!!
//在其他型号的驱动芯片上没有测试!
void LCD_Init(void)
{
//尝试9341 ID的读取
LCD_WR_REG(0XD3);
lcddev.id=LCD_RD_DATA(); //dummy read
lcddev.id=LCD_RD_DATA(); //读到0X00
lcddev.id=LCD_RD_DATA(); //读取93
lcddev.id<<=8;
lcddev.id|=LCD_RD_DATA(); //读取41
if(lcddev.id!=0X9341) //非9341,尝试是不是7789
{
LCD_WR_REG(0X04);
lcddev.id = LCD_RD_DATA(); //dummy read
lcddev.id = LCD_RD_DATA(); //读到0X85
lcddev.id = LCD_RD_DATA(); //读取0X85
lcddev.id <<= 8;
lcddev.id |= LCD_RD_DATA(); //读取0X52
if (lcddev.id == 0X8552) //将8552的ID转换成7789
{
lcddev.id = 0x7789;
}
if (lcddev.id != 0x7789) //也不是ST7789, 尝试是不是 7789
{
LCD_WR_REG(0XD4);
lcddev.id=LCD_RD_DATA();//dummy read
lcddev.id=LCD_RD_DATA();//读回0X01
lcddev.id=LCD_RD_DATA();//读回0X53
lcddev.id<<=8;
lcddev.id|=LCD_RD_DATA(); //这里读回0X10
if(lcddev.id!=0X5310) //也不是NT35310,尝试看看是不是NT35510
{
LCD_WR_REG(0XDA00);
lcddev.id=LCD_RD_DATA(); //读回0X00
LCD_WR_REG(0XDB00);
lcddev.id=LCD_RD_DATA(); //读回0X80
lcddev.id<<=8;
LCD_WR_REG(0XDC00);
lcddev.id|=LCD_RD_DATA(); //读回0X00
if(lcddev.id==0x8000)lcddev.id=0x5510;//NT35510读回的ID是8000H,为方便区分,我们强制设置为5510
if(lcddev.id!=0X5510) //也不是NT5510,尝试看看是不是SSD1963
{
LCD_WR_REG(0XA1);
lcddev.id=LCD_RD_DATA();
lcddev.id=LCD_RD_DATA(); //读回0X57
lcddev.id<<=8;
lcddev.id|=LCD_RD_DATA(); //读回0X61
if(lcddev.id==0X5761)lcddev.id=0X1963;//SSD1963读回的ID是5761H,为方便区分,我们强制设置为1963
}
}
}
}
printf("LCD ID:%x\r\n",lcddev.id); //打印LCD ID
if(lcddev.id==0X9341) //9341初始化
{
LCD_WR_REG(0xCF);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xC1);
LCD_WR_DATA(0X30);
LCD_WR_REG(0xED);
LCD_WR_DATA(0x64);
LCD_WR_DATA(0x03);
LCD_WR_DATA(0X12);
LCD_WR_DATA(0X81);
LCD_WR_REG(0xE8);
LCD_WR_DATA(0x85);
LCD_WR_DATA(0x10);
LCD_WR_DATA(0x7A);
LCD_WR_REG(0xCB);
LCD_WR_DATA(0x39);
LCD_WR_DATA(0x2C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x34);
LCD_WR_DATA(0x02);
LCD_WR_REG(0xF7);
LCD_WR_DATA(0x20);
LCD_WR_REG(0xEA);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC0); //Power control
LCD_WR_DATA(0x1B); //VRH[5:0]
LCD_WR_REG(0xC1); //Power control
LCD_WR_DATA(0x01); //SAP[2:0];BT[3:0]
LCD_WR_REG(0xC5); //VCM control
LCD_WR_DATA(0x30); //3F
LCD_WR_DATA(0x30); //3C
LCD_WR_REG(0xC7); //VCM control2
LCD_WR_DATA(0XB7);
LCD_WR_REG(0x36); // Memory Access Control
LCD_WR_DATA(0x48);
LCD_WR_REG(0x3A);
LCD_WR_DATA(0x55);
LCD_WR_REG(0xB1);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x1A);
LCD_WR_REG(0xB6); // Display Function Control
LCD_WR_DATA(0x0A);
LCD_WR_DATA(0xA2);
LCD_WR_REG(0xF2); // 3Gamma Function Disable
LCD_WR_DATA(0x00);
LCD_WR_REG(0x26); //Gamma curve selected
LCD_WR_DATA(0x01);
LCD_WR_REG(0xE0); //Set Gamma
LCD_WR_DATA(0x0F);
LCD_WR_DATA(0x2A);
LCD_WR_DATA(0x28);
LCD_WR_DATA(0x08);
LCD_WR_DATA(0x0E);
LCD_WR_DATA(0x08);
LCD_WR_DATA(0x54);
LCD_WR_DATA(0XA9);
LCD_WR_DATA(0x43);
LCD_WR_DATA(0x0A);
LCD_WR_DATA(0x0F);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0XE1); //Set Gamma
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x15);
LCD_WR_DATA(0x17);
LCD_WR_DATA(0x07);
LCD_WR_DATA(0x11);
LCD_WR_DATA(0x06);
LCD_WR_DATA(0x2B);
LCD_WR_DATA(0x56);
LCD_WR_DATA(0x3C);
LCD_WR_DATA(0x05);
LCD_WR_DATA(0x10);
LCD_WR_DATA(0x0F);
LCD_WR_DATA(0x3F);
LCD_WR_DATA(0x3F);
LCD_WR_DATA(0x0F);
LCD_WR_REG(0x2B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x01);
LCD_WR_DATA(0x3f);
LCD_WR_REG(0x2A);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xef);
LCD_WR_REG(0x11); //Exit Sleep
HAL_Delay(120);
LCD_WR_REG(0x29); //display on
}
else if(lcddev.id==0x7789) //7789初始化
{
LCD_WR_REG(0x11);
HAL_Delay(120);
LCD_WR_REG(0x36);
LCD_WR_DATA(0x00);
LCD_WR_REG(0x3A);
LCD_WR_DATA(0X05);
LCD_WR_REG(0xB2);
LCD_WR_DATA(0x0C);
LCD_WR_DATA(0x0C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x33);
LCD_WR_DATA(0x33);
LCD_WR_REG(0xB7);
LCD_WR_DATA(0x35);
LCD_WR_REG(0xBB); //vcom
LCD_WR_DATA(0x32); //30
LCD_WR_REG(0xC0);
LCD_WR_DATA(0x0C);
LCD_WR_REG(0xC2);
LCD_WR_DATA(0x01);
LCD_WR_REG(0xC3); //vrh
LCD_WR_DATA(0x10); //17 0D
LCD_WR_REG(0xC4); //vdv
LCD_WR_DATA(0x20); //20
LCD_WR_REG(0xC6);
LCD_WR_DATA(0x0f);
LCD_WR_REG(0xD0);
LCD_WR_DATA(0xA4);
LCD_WR_DATA(0xA1);
LCD_WR_REG(0xE0); //Set Gamma
LCD_WR_DATA(0xd0);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x02);
LCD_WR_DATA(0x07);
LCD_WR_DATA(0x0a);
LCD_WR_DATA(0x28);
LCD_WR_DATA(0x32);
LCD_WR_DATA(0X44);
LCD_WR_DATA(0x42);
LCD_WR_DATA(0x06);
LCD_WR_DATA(0x0e);
LCD_WR_DATA(0x12);
LCD_WR_DATA(0x14);
LCD_WR_DATA(0x17);
LCD_WR_REG(0XE1); //Set Gamma
LCD_WR_DATA(0xd0);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x02);
LCD_WR_DATA(0x07);
LCD_WR_DATA(0x0a);
LCD_WR_DATA(0x28);
LCD_WR_DATA(0x31);
LCD_WR_DATA(0x54);
LCD_WR_DATA(0x47);
LCD_WR_DATA(0x0e);
LCD_WR_DATA(0x1c);
LCD_WR_DATA(0x17);
LCD_WR_DATA(0x1b);
LCD_WR_DATA(0x1e);
LCD_WR_REG(0x2A);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xef);
LCD_WR_REG(0x2B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x01);
LCD_WR_DATA(0x3f);
LCD_WR_REG(0x29); //display on
}
else if(lcddev.id==0x5310)
{
LCD_WR_REG(0xED);
LCD_WR_DATA(0x01);
LCD_WR_DATA(0xFE);
LCD_WR_REG(0xEE);
LCD_WR_DATA(0xDE);
LCD_WR_DATA(0x21);
LCD_WR_REG(0xF1);
LCD_WR_DATA(0x01);
LCD_WR_REG(0xDF);
LCD_WR_DATA(0x10);
//VCOMvoltage//
LCD_WR_REG(0xC4);
LCD_WR_DATA(0x8F); //5f
LCD_WR_REG(0xC6);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xE2);
LCD_WR_DATA(0xE2);
LCD_WR_DATA(0xE2);
LCD_WR_REG(0xBF);
LCD_WR_DATA(0xAA);
LCD_WR_REG(0xB0);
LCD_WR_DATA(0x0D);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x0D);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x11);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x19);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x21);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x2D);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x3D);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x5D);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x5D);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xB1);
LCD_WR_DATA(0x80);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x8B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x96);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xB2);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x02);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x03);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xB3);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xB4);
LCD_WR_DATA(0x8B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x96);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xA1);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xB5);
LCD_WR_DATA(0x02);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x03);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x04);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xB6);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xB7);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x3F);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x5E);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x64);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x8C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xAC);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xDC);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x70);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x90);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xEB);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xDC);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xB8);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xBA);
LCD_WR_DATA(0x24);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC1);
LCD_WR_DATA(0x20);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x54);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xFF);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC2);
LCD_WR_DATA(0x0A);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x04);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC3);
LCD_WR_DATA(0x3C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x3A);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x39);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x37);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x3C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x36);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x32);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x2F);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x2C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x29);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x26);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x24);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x24);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x23);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x3C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x36);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x32);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x2F);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x2C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x29);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x26);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x24);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x24);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x23);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC4);
LCD_WR_DATA(0x62);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x05);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x84);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xF0);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x18);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xA4);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x18);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x50);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x0C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x17);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x95);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xF3);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xE6);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC5);
LCD_WR_DATA(0x32);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x44);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x65);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x76);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x88);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC6);
LCD_WR_DATA(0x20);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x17);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x01);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC7);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC8);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xC9);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE0);
LCD_WR_DATA(0x16);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x1C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x21);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x36);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x46);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x52);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x64);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x7A);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x8B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x99);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xA8);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xB9);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xC4);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xCA);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD2);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD9);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xE0);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xF3);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE1);
LCD_WR_DATA(0x16);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x1C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x22);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x36);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x45);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x52);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x64);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x7A);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x8B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x99);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xA8);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xB9);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xC4);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xCA);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD2);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD8);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xE0);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xF3);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE2);
LCD_WR_DATA(0x05);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x0B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x1B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x34);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x44);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x4F);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x61);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x79);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x88);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x97);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xA6);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xB7);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xC2);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xC7);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD1);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD6);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xDD);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xF3);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE3);
LCD_WR_DATA(0x05);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xA);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x1C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x33);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x44);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x50);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x62);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x78);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x88);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x97);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xA6);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xB7);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xC2);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xC7);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD1);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD5);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xDD);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xF3);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE4);
LCD_WR_DATA(0x01);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x01);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x02);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x2A);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x3C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x4B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x5D);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x74);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x84);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x93);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xA2);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xB3);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xBE);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xC4);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xCD);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD3);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xDD);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xF3);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE5);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x02);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x29);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x3C);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x4B);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x5D);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x74);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x84);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x93);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xA2);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xB3);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xBE);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xC4);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xCD);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xD3);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xDC);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xF3);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE6);
LCD_WR_DATA(0x11);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x34);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x56);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x76);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x77);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x66);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x88);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x99);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xBB);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x99);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x66);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x55);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x55);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x45);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x43);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x44);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE7);
LCD_WR_DATA(0x32);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x55);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x76);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x66);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x67);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x67);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x87);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x99);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xBB);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x99);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x77);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x44);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x56);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x23);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x33);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x45);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE8);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x99);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x87);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x88);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x77);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x66);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x88);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xAA);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0xBB);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x99);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x66);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x55);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x55);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x44);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x44);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x55);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xE9);
LCD_WR_DATA(0xAA);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0x00);
LCD_WR_DATA(0xAA);
LCD_WR_REG(0xCF);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xF0);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x50);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xF3);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xF9);
LCD_WR_DATA(0x06);
LCD_WR_DATA(0x10);
LCD_WR_DATA(0x29);
LCD_WR_DATA(0x00);
LCD_WR_REG(0x3A);
LCD_WR_DATA(0x55); //66
LCD_WR_REG(0x11);
HAL_Delay(100);
LCD_WR_REG(0x29);
LCD_WR_REG(0x35);
LCD_WR_DATA(0x00);
LCD_WR_REG(0x51);
LCD_WR_DATA(0xFF);
LCD_WR_REG(0x53);
LCD_WR_DATA(0x2C);
LCD_WR_REG(0x55);
LCD_WR_DATA(0x82);
LCD_WR_REG(0x2c);
}
else if(lcddev.id==0x5510)
{
LCD_WriteReg(0xF000,0x55);
LCD_WriteReg(0xF001,0xAA);
LCD_WriteReg(0xF002,0x52);
LCD_WriteReg(0xF003,0x08);
LCD_WriteReg(0xF004,0x01);
//AVDD Set AVDD 5.2V
LCD_WriteReg(0xB000,0x0D);
LCD_WriteReg(0xB001,0x0D);
LCD_WriteReg(0xB002,0x0D);
//AVDD ratio
LCD_WriteReg(0xB600,0x34);
LCD_WriteReg(0xB601,0x34);
LCD_WriteReg(0xB602,0x34);
//AVEE -5.2V
LCD_WriteReg(0xB100,0x0D);
LCD_WriteReg(0xB101,0x0D);
LCD_WriteReg(0xB102,0x0D);
//AVEE ratio
LCD_WriteReg(0xB700,0x34);
LCD_WriteReg(0xB701,0x34);
LCD_WriteReg(0xB702,0x34);
//VCL -2.5V
LCD_WriteReg(0xB200,0x00);
LCD_WriteReg(0xB201,0x00);
LCD_WriteReg(0xB202,0x00);
//VCL ratio
LCD_WriteReg(0xB800,0x24);
LCD_WriteReg(0xB801,0x24);
LCD_WriteReg(0xB802,0x24);
//VGH 15V (Free pump)
LCD_WriteReg(0xBF00,0x01);
LCD_WriteReg(0xB300,0x0F);
LCD_WriteReg(0xB301,0x0F);
LCD_WriteReg(0xB302,0x0F);
//VGH ratio
LCD_WriteReg(0xB900,0x34);
LCD_WriteReg(0xB901,0x34);
LCD_WriteReg(0xB902,0x34);
//VGL_REG -10V
LCD_WriteReg(0xB500,0x08);
LCD_WriteReg(0xB501,0x08);
LCD_WriteReg(0xB502,0x08);
LCD_WriteReg(0xC200,0x03);
//VGLX ratio
LCD_WriteReg(0xBA00,0x24);
LCD_WriteReg(0xBA01,0x24);
LCD_WriteReg(0xBA02,0x24);
//VGMP/VGSP 4.5V/0V
LCD_WriteReg(0xBC00,0x00);
LCD_WriteReg(0xBC01,0x78);
LCD_WriteReg(0xBC02,0x00);
//VGMN/VGSN -4.5V/0V
LCD_WriteReg(0xBD00,0x00);
LCD_WriteReg(0xBD01,0x78);
LCD_WriteReg(0xBD02,0x00);
//VCOM
LCD_WriteReg(0xBE00,0x00);
LCD_WriteReg(0xBE01,0x64);
//Gamma Setting
LCD_WriteReg(0xD100,0x00);
LCD_WriteReg(0xD101,0x33);
LCD_WriteReg(0xD102,0x00);
LCD_WriteReg(0xD103,0x34);
LCD_WriteReg(0xD104,0x00);
LCD_WriteReg(0xD105,0x3A);
LCD_WriteReg(0xD106,0x00);
LCD_WriteReg(0xD107,0x4A);
LCD_WriteReg(0xD108,0x00);
LCD_WriteReg(0xD109,0x5C);
LCD_WriteReg(0xD10A,0x00);
LCD_WriteReg(0xD10B,0x81);
LCD_WriteReg(0xD10C,0x00);
LCD_WriteReg(0xD10D,0xA6);
LCD_WriteReg(0xD10E,0x00);
LCD_WriteReg(0xD10F,0xE5);
LCD_WriteReg(0xD110,0x01);
LCD_WriteReg(0xD111,0x13);
LCD_WriteReg(0xD112,0x01);
LCD_WriteReg(0xD113,0x54);
LCD_WriteReg(0xD114,0x01);
LCD_WriteReg(0xD115,0x82);
LCD_WriteReg(0xD116,0x01);
LCD_WriteReg(0xD117,0xCA);
LCD_WriteReg(0xD118,0x02);
LCD_WriteReg(0xD119,0x00);
LCD_WriteReg(0xD11A,0x02);
LCD_WriteReg(0xD11B,0x01);
LCD_WriteReg(0xD11C,0x02);
LCD_WriteReg(0xD11D,0x34);
LCD_WriteReg(0xD11E,0x02);
LCD_WriteReg(0xD11F,0x67);
LCD_WriteReg(0xD120,0x02);
LCD_WriteReg(0xD121,0x84);
LCD_WriteReg(0xD122,0x02);
LCD_WriteReg(0xD123,0xA4);
LCD_WriteReg(0xD124,0x02);
LCD_WriteReg(0xD125,0xB7);
LCD_WriteReg(0xD126,0x02);
LCD_WriteReg(0xD127,0xCF);
LCD_WriteReg(0xD128,0x02);
LCD_WriteReg(0xD129,0xDE);
LCD_WriteReg(0xD12A,0x02);
LCD_WriteReg(0xD12B,0xF2);
LCD_WriteReg(0xD12C,0x02);
LCD_WriteReg(0xD12D,0xFE);
LCD_WriteReg(0xD12E,0x03);
LCD_WriteReg(0xD12F,0x10);
LCD_WriteReg(0xD130,0x03);
LCD_WriteReg(0xD131,0x33);
LCD_WriteReg(0xD132,0x03);
LCD_WriteReg(0xD133,0x6D);
LCD_WriteReg(0xD200,0x00);
LCD_WriteReg(0xD201,0x33);
LCD_WriteReg(0xD202,0x00);
LCD_WriteReg(0xD203,0x34);
LCD_WriteReg(0xD204,0x00);
LCD_WriteReg(0xD205,0x3A);
LCD_WriteReg(0xD206,0x00);
LCD_WriteReg(0xD207,0x4A);
LCD_WriteReg(0xD208,0x00);
LCD_WriteReg(0xD209,0x5C);
LCD_WriteReg(0xD20A,0x00);
LCD_WriteReg(0xD20B,0x81);
LCD_WriteReg(0xD20C,0x00);
LCD_WriteReg(0xD20D,0xA6);
LCD_WriteReg(0xD20E,0x00);
LCD_WriteReg(0xD20F,0xE5);
LCD_WriteReg(0xD210,0x01);
LCD_WriteReg(0xD211,0x13);
LCD_WriteReg(0xD212,0x01);
LCD_WriteReg(0xD213,0x54);
LCD_WriteReg(0xD214,0x01);
LCD_WriteReg(0xD215,0x82);
LCD_WriteReg(0xD216,0x01);
LCD_WriteReg(0xD217,0xCA);
LCD_WriteReg(0xD218,0x02);
LCD_WriteReg(0xD219,0x00);
LCD_WriteReg(0xD21A,0x02);
LCD_WriteReg(0xD21B,0x01);
LCD_WriteReg(0xD21C,0x02);
LCD_WriteReg(0xD21D,0x34);
LCD_WriteReg(0xD21E,0x02);
LCD_WriteReg(0xD21F,0x67);
LCD_WriteReg(0xD220,0x02);
LCD_WriteReg(0xD221,0x84);
LCD_WriteReg(0xD222,0x02);
LCD_WriteReg(0xD223,0xA4);
LCD_WriteReg(0xD224,0x02);
LCD_WriteReg(0xD225,0xB7);
LCD_WriteReg(0xD226,0x02);
LCD_WriteReg(0xD227,0xCF);
LCD_WriteReg(0xD228,0x02);
LCD_WriteReg(0xD229,0xDE);
LCD_WriteReg(0xD22A,0x02);
LCD_WriteReg(0xD22B,0xF2);
LCD_WriteReg(0xD22C,0x02);
LCD_WriteReg(0xD22D,0xFE);
LCD_WriteReg(0xD22E,0x03);
LCD_WriteReg(0xD22F,0x10);
LCD_WriteReg(0xD230,0x03);
LCD_WriteReg(0xD231,0x33);
LCD_WriteReg(0xD232,0x03);
LCD_WriteReg(0xD233,0x6D);
LCD_WriteReg(0xD300,0x00);
LCD_WriteReg(0xD301,0x33);
LCD_WriteReg(0xD302,0x00);
LCD_WriteReg(0xD303,0x34);
LCD_WriteReg(0xD304,0x00);
LCD_WriteReg(0xD305,0x3A);
LCD_WriteReg(0xD306,0x00);
LCD_WriteReg(0xD307,0x4A);
LCD_WriteReg(0xD308,0x00);
LCD_WriteReg(0xD309,0x5C);
LCD_WriteReg(0xD30A,0x00);
LCD_WriteReg(0xD30B,0x81);
LCD_WriteReg(0xD30C,0x00);
LCD_WriteReg(0xD30D,0xA6);
LCD_WriteReg(0xD30E,0x00);
LCD_WriteReg(0xD30F,0xE5);
LCD_WriteReg(0xD310,0x01);
LCD_WriteReg(0xD311,0x13);
LCD_WriteReg(0xD312,0x01);
LCD_WriteReg(0xD313,0x54);
LCD_WriteReg(0xD314,0x01);
LCD_WriteReg(0xD315,0x82);
LCD_WriteReg(0xD316,0x01);
LCD_WriteReg(0xD317,0xCA);
LCD_WriteReg(0xD318,0x02);
LCD_WriteReg(0xD319,0x00);
LCD_WriteReg(0xD31A,0x02);
LCD_WriteReg(0xD31B,0x01);
LCD_WriteReg(0xD31C,0x02);
LCD_WriteReg(0xD31D,0x34);
LCD_WriteReg(0xD31E,0x02);
LCD_WriteReg(0xD31F,0x67);
LCD_WriteReg(0xD320,0x02);
LCD_WriteReg(0xD321,0x84);
LCD_WriteReg(0xD322,0x02);
LCD_WriteReg(0xD323,0xA4);
LCD_WriteReg(0xD324,0x02);
LCD_WriteReg(0xD325,0xB7);
LCD_WriteReg(0xD326,0x02);
LCD_WriteReg(0xD327,0xCF);
LCD_WriteReg(0xD328,0x02);
LCD_WriteReg(0xD329,0xDE);
LCD_WriteReg(0xD32A,0x02);
LCD_WriteReg(0xD32B,0xF2);
LCD_WriteReg(0xD32C,0x02);
LCD_WriteReg(0xD32D,0xFE);
LCD_WriteReg(0xD32E,0x03);
LCD_WriteReg(0xD32F,0x10);
LCD_WriteReg(0xD330,0x03);
LCD_WriteReg(0xD331,0x33);
LCD_WriteReg(0xD332,0x03);
LCD_WriteReg(0xD333,0x6D);
LCD_WriteReg(0xD400,0x00);
LCD_WriteReg(0xD401,0x33);
LCD_WriteReg(0xD402,0x00);
LCD_WriteReg(0xD403,0x34);
LCD_WriteReg(0xD404,0x00);
LCD_WriteReg(0xD405,0x3A);
LCD_WriteReg(0xD406,0x00);
LCD_WriteReg(0xD407,0x4A);
LCD_WriteReg(0xD408,0x00);
LCD_WriteReg(0xD409,0x5C);
LCD_WriteReg(0xD40A,0x00);
LCD_WriteReg(0xD40B,0x81);
LCD_WriteReg(0xD40C,0x00);
LCD_WriteReg(0xD40D,0xA6);
LCD_WriteReg(0xD40E,0x00);
LCD_WriteReg(0xD40F,0xE5);
LCD_WriteReg(0xD410,0x01);
LCD_WriteReg(0xD411,0x13);
LCD_WriteReg(0xD412,0x01);
LCD_WriteReg(0xD413,0x54);
LCD_WriteReg(0xD414,0x01);
LCD_WriteReg(0xD415,0x82);
LCD_WriteReg(0xD416,0x01);
LCD_WriteReg(0xD417,0xCA);
LCD_WriteReg(0xD418,0x02);
LCD_WriteReg(0xD419,0x00);
LCD_WriteReg(0xD41A,0x02);
LCD_WriteReg(0xD41B,0x01);
LCD_WriteReg(0xD41C,0x02);
LCD_WriteReg(0xD41D,0x34);
LCD_WriteReg(0xD41E,0x02);
LCD_WriteReg(0xD41F,0x67);
LCD_WriteReg(0xD420,0x02);
LCD_WriteReg(0xD421,0x84);
LCD_WriteReg(0xD422,0x02);
LCD_WriteReg(0xD423,0xA4);
LCD_WriteReg(0xD424,0x02);
LCD_WriteReg(0xD425,0xB7);
LCD_WriteReg(0xD426,0x02);
LCD_WriteReg(0xD427,0xCF);
LCD_WriteReg(0xD428,0x02);
LCD_WriteReg(0xD429,0xDE);
LCD_WriteReg(0xD42A,0x02);
LCD_WriteReg(0xD42B,0xF2);
LCD_WriteReg(0xD42C,0x02);
LCD_WriteReg(0xD42D,0xFE);
LCD_WriteReg(0xD42E,0x03);
LCD_WriteReg(0xD42F,0x10);
LCD_WriteReg(0xD430,0x03);
LCD_WriteReg(0xD431,0x33);
LCD_WriteReg(0xD432,0x03);
LCD_WriteReg(0xD433,0x6D);
LCD_WriteReg(0xD500,0x00);
LCD_WriteReg(0xD501,0x33);
LCD_WriteReg(0xD502,0x00);
LCD_WriteReg(0xD503,0x34);
LCD_WriteReg(0xD504,0x00);
LCD_WriteReg(0xD505,0x3A);
LCD_WriteReg(0xD506,0x00);
LCD_WriteReg(0xD507,0x4A);
LCD_WriteReg(0xD508,0x00);
LCD_WriteReg(0xD509,0x5C);
LCD_WriteReg(0xD50A,0x00);
LCD_WriteReg(0xD50B,0x81);
LCD_WriteReg(0xD50C,0x00);
LCD_WriteReg(0xD50D,0xA6);
LCD_WriteReg(0xD50E,0x00);
LCD_WriteReg(0xD50F,0xE5);
LCD_WriteReg(0xD510,0x01);
LCD_WriteReg(0xD511,0x13);
LCD_WriteReg(0xD512,0x01);
LCD_WriteReg(0xD513,0x54);
LCD_WriteReg(0xD514,0x01);
LCD_WriteReg(0xD515,0x82);
LCD_WriteReg(0xD516,0x01);
LCD_WriteReg(0xD517,0xCA);
LCD_WriteReg(0xD518,0x02);
LCD_WriteReg(0xD519,0x00);
LCD_WriteReg(0xD51A,0x02);
LCD_WriteReg(0xD51B,0x01);
LCD_WriteReg(0xD51C,0x02);
LCD_WriteReg(0xD51D,0x34);
LCD_WriteReg(0xD51E,0x02);
LCD_WriteReg(0xD51F,0x67);
LCD_WriteReg(0xD520,0x02);
LCD_WriteReg(0xD521,0x84);
LCD_WriteReg(0xD522,0x02);
LCD_WriteReg(0xD523,0xA4);
LCD_WriteReg(0xD524,0x02);
LCD_WriteReg(0xD525,0xB7);
LCD_WriteReg(0xD526,0x02);
LCD_WriteReg(0xD527,0xCF);
LCD_WriteReg(0xD528,0x02);
LCD_WriteReg(0xD529,0xDE);
LCD_WriteReg(0xD52A,0x02);
LCD_WriteReg(0xD52B,0xF2);
LCD_WriteReg(0xD52C,0x02);
LCD_WriteReg(0xD52D,0xFE);
LCD_WriteReg(0xD52E,0x03);
LCD_WriteReg(0xD52F,0x10);
LCD_WriteReg(0xD530,0x03);
LCD_WriteReg(0xD531,0x33);
LCD_WriteReg(0xD532,0x03);
LCD_WriteReg(0xD533,0x6D);
LCD_WriteReg(0xD600,0x00);
LCD_WriteReg(0xD601,0x33);
LCD_WriteReg(0xD602,0x00);
LCD_WriteReg(0xD603,0x34);
LCD_WriteReg(0xD604,0x00);
LCD_WriteReg(0xD605,0x3A);
LCD_WriteReg(0xD606,0x00);
LCD_WriteReg(0xD607,0x4A);
LCD_WriteReg(0xD608,0x00);
LCD_WriteReg(0xD609,0x5C);
LCD_WriteReg(0xD60A,0x00);
LCD_WriteReg(0xD60B,0x81);
LCD_WriteReg(0xD60C,0x00);
LCD_WriteReg(0xD60D,0xA6);
LCD_WriteReg(0xD60E,0x00);
LCD_WriteReg(0xD60F,0xE5);
LCD_WriteReg(0xD610,0x01);
LCD_WriteReg(0xD611,0x13);
LCD_WriteReg(0xD612,0x01);
LCD_WriteReg(0xD613,0x54);
LCD_WriteReg(0xD614,0x01);
LCD_WriteReg(0xD615,0x82);
LCD_WriteReg(0xD616,0x01);
LCD_WriteReg(0xD617,0xCA);
LCD_WriteReg(0xD618,0x02);
LCD_WriteReg(0xD619,0x00);
LCD_WriteReg(0xD61A,0x02);
LCD_WriteReg(0xD61B,0x01);
LCD_WriteReg(0xD61C,0x02);
LCD_WriteReg(0xD61D,0x34);
LCD_WriteReg(0xD61E,0x02);
LCD_WriteReg(0xD61F,0x67);
LCD_WriteReg(0xD620,0x02);
LCD_WriteReg(0xD621,0x84);
LCD_WriteReg(0xD622,0x02);
LCD_WriteReg(0xD623,0xA4);
LCD_WriteReg(0xD624,0x02);
LCD_WriteReg(0xD625,0xB7);
LCD_WriteReg(0xD626,0x02);
LCD_WriteReg(0xD627,0xCF);
LCD_WriteReg(0xD628,0x02);
LCD_WriteReg(0xD629,0xDE);
LCD_WriteReg(0xD62A,0x02);
LCD_WriteReg(0xD62B,0xF2);
LCD_WriteReg(0xD62C,0x02);
LCD_WriteReg(0xD62D,0xFE);
LCD_WriteReg(0xD62E,0x03);
LCD_WriteReg(0xD62F,0x10);
LCD_WriteReg(0xD630,0x03);
LCD_WriteReg(0xD631,0x33);
LCD_WriteReg(0xD632,0x03);
LCD_WriteReg(0xD633,0x6D);
//LV2 Page 0 enable
LCD_WriteReg(0xF000,0x55);
LCD_WriteReg(0xF001,0xAA);
LCD_WriteReg(0xF002,0x52);
LCD_WriteReg(0xF003,0x08);
LCD_WriteReg(0xF004,0x00);
//Display control
LCD_WriteReg(0xB100, 0xCC);
LCD_WriteReg(0xB101, 0x00);
//Source hold time
LCD_WriteReg(0xB600,0x05);
//Gate EQ control
LCD_WriteReg(0xB700,0x70);
LCD_WriteReg(0xB701,0x70);
//Source EQ control (Mode 2)
LCD_WriteReg(0xB800,0x01);
LCD_WriteReg(0xB801,0x03);
LCD_WriteReg(0xB802,0x03);
LCD_WriteReg(0xB803,0x03);
//Inversion mode (2-dot)
LCD_WriteReg(0xBC00,0x02);
LCD_WriteReg(0xBC01,0x00);
LCD_WriteReg(0xBC02,0x00);
//Timing control 4H w/ 4-delay
LCD_WriteReg(0xC900,0xD0);
LCD_WriteReg(0xC901,0x02);
LCD_WriteReg(0xC902,0x50);
LCD_WriteReg(0xC903,0x50);
LCD_WriteReg(0xC904,0x50);
LCD_WriteReg(0x3500,0x00);
LCD_WriteReg(0x3A00,0x55); //16-bit/pixel
LCD_WR_REG(0x1100);
delay_us(120);
LCD_WR_REG(0x2900);
}
else if(lcddev.id==0X1963)
{
LCD_WR_REG(0xE2); //Set PLL with OSC = 10MHz (hardware), Multiplier N = 35, 250MHz < VCO < 800MHz = OSC*(N+1), VCO = 300MHz
LCD_WR_DATA(0x1D); //参数1
LCD_WR_DATA(0x02); //参数2 Divider M = 2, PLL = 300/(M+1) = 100MHz
LCD_WR_DATA(0x04); //参数3 Validate M and N values
delay_us(100);
LCD_WR_REG(0xE0); // Start PLL command
LCD_WR_DATA(0x01); // enable PLL
HAL_Delay(10);
LCD_WR_REG(0xE0); // Start PLL command again
LCD_WR_DATA(0x03); // now, use PLL output as system clock
HAL_Delay(12);
LCD_WR_REG(0x01); //软复位
HAL_Delay(10);
LCD_WR_REG(0xE6); //设置像素频率,33Mhz
LCD_WR_DATA(0x2F);
LCD_WR_DATA(0xFF);
LCD_WR_DATA(0xFF);
LCD_WR_REG(0xB0); //设置LCD模式
LCD_WR_DATA(0x20); //24位模式
LCD_WR_DATA(0x00); //TFT 模式
LCD_WR_DATA((SSD_HOR_RESOLUTION-1)>>8);//设置LCD水平像素
LCD_WR_DATA(SSD_HOR_RESOLUTION-1);
LCD_WR_DATA((SSD_VER_RESOLUTION-1)>>8);//设置LCD垂直像素
LCD_WR_DATA(SSD_VER_RESOLUTION-1);
LCD_WR_DATA(0x00); //RGB序列
LCD_WR_REG(0xB4); //Set horizontal period
LCD_WR_DATA((SSD_HT-1)>>8);
LCD_WR_DATA(SSD_HT-1);
LCD_WR_DATA(SSD_HPS>>8);
LCD_WR_DATA(SSD_HPS);
LCD_WR_DATA(SSD_HOR_PULSE_WIDTH-1);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xB6); //Set vertical period
LCD_WR_DATA((SSD_VT-1)>>8);
LCD_WR_DATA(SSD_VT-1);
LCD_WR_DATA(SSD_VPS>>8);
LCD_WR_DATA(SSD_VPS);
LCD_WR_DATA(SSD_VER_FRONT_PORCH-1);
LCD_WR_DATA(0x00);
LCD_WR_DATA(0x00);
LCD_WR_REG(0xF0); //设置SSD1963与CPU接口为16bit
LCD_WR_DATA(0x03); //16-bit(565 format) data for 16bpp
LCD_WR_REG(0x29); //开启显示
//设置PWM输出 背光通过占空比可调
LCD_WR_REG(0xD0); //设置自动白平衡DBC
LCD_WR_DATA(0x00); //disable
LCD_WR_REG(0xBE); //配置PWM输出
LCD_WR_DATA(0x05); //1设置PWM频率
LCD_WR_DATA(0xFE); //2设置PWM占空比
LCD_WR_DATA(0x01); //3设置C
LCD_WR_DATA(0x00); //4设置D
LCD_WR_DATA(0x00); //5设置E
LCD_WR_DATA(0x00); //6设置F
LCD_WR_REG(0xB8); //设置GPIO配置
LCD_WR_DATA(0x03); //2个IO口设置成输出
LCD_WR_DATA(0x01); //GPIO使用正常的IO功能
LCD_WR_REG(0xBA);
LCD_WR_DATA(0X01); //GPIO[1:0]=01,控制LCD方向
LCD_SSD_BackLightSet(100);//背光设置为最亮
}
//初始化完成以后,提速
if(lcddev.id==0X9341||lcddev.id==0X5310||lcddev.id==0X5510||lcddev.id==0X1963)//如果是这几个IC,则设置WR时序为最快
{
//重新配置写时序控制寄存器的时序
FSMC_Bank1E->BWTR[6]&=~(0XF<<0);//地址建立时间(ADDSET)清零
FSMC_Bank1E->BWTR[6]&=~(0XF<<8);//数据保存时间清零
FSMC_Bank1E->BWTR[6]|=3<<0; //地址建立时间(ADDSET)为3个HCLK =18ns
FSMC_Bank1E->BWTR[6]|=2<<8; //数据保存时间(DATAST)为6ns*3个HCLK=18ns
}
LCD_Display_Dir(0); //默认为竖屏
HAL_GPIO_WritePin(LCD_BLK_GPIO_Port, LCD_BLK_Pin, GPIO_PIN_SET); //点亮背光
LCD_Clear(WHITE);
}
//清屏函数
//color:要清屏的填充色
void LCD_Clear(uint32_t color)
{
uint32_t index=0;
uint32_t totalpoint=lcddev.width;
totalpoint*=lcddev.height; //得到总点数
LCD_SetCursor(0x00,0x0000); //设置光标位置
LCD_WriteRAM_Prepare(); //开始写入GRAM
for(index=0; index<totalpoint; index++)
{
LCD->LCD_RAM=color;
}
}
//在指定区域内填充单个颜色
//(sx,sy),(ex,ey):填充矩形对角坐标,区域大小为:(ex-sx+1)*(ey-sy+1)
//color:要填充的颜色
void LCD_Fill(uint16_t sx,uint16_t sy,uint16_t ex,uint16_t ey,uint32_t color)
{
uint16_t i,j;
uint16_t xlen=0;
xlen=ex-sx+1;
for(i=sy; i<=ey; i++)
{
LCD_SetCursor(sx,i); //设置光标位置
LCD_WriteRAM_Prepare(); //开始写入GRAM
for (j = 0; j < xlen; j++)
{
LCD->LCD_RAM=color; //设置光标位置
}
}
}
//在指定区域内填充指定颜色块
//(sx,sy),(ex,ey):填充矩形对角坐标,区域大小为:(ex-sx+1)*(ey-sy+1)
//color:要填充的颜色
void LCD_Color_Fill(uint16_t sx,uint16_t sy,uint16_t ex,uint16_t ey,uint16_t *color)
{
uint16_t height,width;
uint16_t i,j;
width=ex-sx+1; //得到填充的宽度
height=ey-sy+1; //高度
for(i=0; i<height; i++)
{
LCD_SetCursor(sx,sy+i); //设置光标位置
LCD_WriteRAM_Prepare(); //开始写入GRAM
for (j = 0; j < width; j++)
{
LCD->LCD_RAM=color[i * width + j]; //写入数据
}
}
}
//画线
//x1,y1:起点坐标
//x2,y2:终点坐标
void LCD_DrawLine(uint16_t x1, uint16_t y1, uint16_t x2, uint16_t y2)
{
uint16_t t;
int xerr = 0, yerr = 0, delta_x, delta_y, distance;
int incx, incy, uRow, uCol;
delta_x = x2 - x1; //计算坐标增量
delta_y = y2 - y1;
uRow = x1;
uCol = y1;
if (delta_x > 0)incx = 1; //设置单步方向
else if (delta_x == 0)incx = 0; //垂直线
else
{
incx = -1;
delta_x = -delta_x;
}
if (delta_y > 0)incy = 1;
else if (delta_y == 0)incy = 0; //水平线
else
{
incy = -1;
delta_y = -delta_y;
}
if ( delta_x > delta_y)distance = delta_x; //选取基本增量坐标轴
else distance = delta_y;
for (t = 0; t <= distance + 1; t++ ) //画线输出
{
LCD_DrawPoint(uRow, uCol); //画点
xerr += delta_x ;
yerr += delta_y ;
if (xerr > distance)
{
xerr -= distance;
uRow += incx;
}
if (yerr > distance)
{
yerr -= distance;
uCol += incy;
}
}
}
//画矩形
//(x1,y1),(x2,y2):矩形的对角坐标
void LCD_DrawRectangle(uint16_t x1, uint16_t y1, uint16_t x2, uint16_t y2)
{
LCD_DrawLine(x1,y1,x2,y1);
LCD_DrawLine(x1,y1,x1,y2);
LCD_DrawLine(x1,y2,x2,y2);
LCD_DrawLine(x2,y1,x2,y2);
}
//在指定位置画一个指定大小的圆
//(x,y):中心点
//r :半径
void LCD_Draw_Circle(uint16_t x0,uint16_t y0,uint8_t r)
{
int a, b;
int di;
a = 0;
b = r;
di = 3 - (r << 1); //判断下个点位置的标志
while (a <= b)
{
LCD_DrawPoint(x0 + a, y0 - b); //5
LCD_DrawPoint(x0 + b, y0 - a); //0
LCD_DrawPoint(x0 + b, y0 + a); //4
LCD_DrawPoint(x0 + a, y0 + b); //6
LCD_DrawPoint(x0 - a, y0 + b); //1
LCD_DrawPoint(x0 - b, y0 + a);
LCD_DrawPoint(x0 - a, y0 - b); //2
LCD_DrawPoint(x0 - b, y0 - a); //7
a++;
//使用Bresenham算法画圆
if (di < 0)di += 4 * a + 6;
else
{
di += 10 + 4 * (a - b);
b--;
}
}
}
//在指定位置显示一个字符
//x,y:起始坐标
//num:要显示的字符:" "--->"~"
//size:字体大小 12/16/24/32
//mode:叠加方式(1)还是非叠加方式(0)
void LCD_ShowChar(uint16_t x,uint16_t y,uint8_t num,uint8_t size,uint8_t mode)
{
uint8_t temp,t1,t;
uint16_t y0=y;
uint8_t csize=(size/8+((size%8)?1:0))*(size/2); //得到字体一个字符对应点阵集所占的字节数
num=num-' ';//得到偏移后的值（ASCII字库是从空格开始取模，所以-' '就是对应字符的字库）
for(t=0; t<csize; t++)
{
if(size==12)temp=asc2_1206[num][t]; //调用1206字体
else if(size==16)temp=asc2_1608[num][t]; //调用1608字体
else if(size==24)temp=asc2_2412[num][t]; //调用2412字体
else if(size==32)temp=asc2_3216[num][t]; //调用3216字体
else return; //没有的字库
for(t1=0; t1<8; t1++)
{
if(temp&0x80)LCD_Fast_DrawPoint(x,y,POINT_COLOR);
else if(mode==0)LCD_Fast_DrawPoint(x,y,BACK_COLOR);
temp<<=1;
y++;
if(y>=lcddev.height)return; //超区域了
if((y-y0)==size)
{
y=y0;
x++;
if(x>=lcddev.width)return; //超区域了
break;
}
}
}
}
//m^n函数，LCD显示数字内部使用
//返回值:m^n次方.
uint32_t _LCD_Pow(uint8_t m,uint8_t n)
{
uint32_t result=1;
while(n--)result*=m;
return result;
}
//显示数字,高位为0,则不显示
//x,y :起点坐标
//len :数字的位数
//size:字体大小
//color:颜色
//num:数值(0~4294967295);
void LCD_ShowNum(uint16_t x, uint16_t y, uint32_t num, uint8_t len, uint8_t size)
{
uint8_t t, temp;
uint8_t enshow = 0;
for (t = 0; t < len; t++)
{
temp = (num / _LCD_Pow(10, len - t - 1)) % 10;
if (enshow == 0 && t < (len - 1))
{
if (temp == 0)
{
LCD_ShowChar(x + (size / 2)*t, y, ' ', size, 0);
continue;
}
else enshow = 1;
}
LCD_ShowChar(x + (size / 2)*t, y, temp + '0', size, 0);
}
}
//显示数字,高位为0,还是显示
//x,y:起点坐标
//num:数值(0~999999999);
//len:长度(即要显示的位数)
//size:字体大小
//mode:
//[7]:0,不填充;1,填充0.
//[6:1]:保留
//[0]:0,非叠加显示;1,叠加显示.
void LCD_ShowxNum(uint16_t x,uint16_t y,uint32_t num,uint8_t len,uint8_t size,uint8_t mode)
{
uint8_t t,temp;
uint8_t enshow=0;
for(t=0; t<len; t++)
{
temp=(num/_LCD_Pow(10,len-t-1))%10;
if(enshow==0&&t<(len-1))
{
if(temp==0)
{
if(mode&0X80)LCD_ShowChar(x+(size/2)*t,y,'0',size,mode&0X01);
else LCD_ShowChar(x+(size/2)*t,y,' ',size,mode&0X01);
continue;
} else enshow=1;
}
LCD_ShowChar(x+(size/2)*t,y,temp+'0',size,mode&0X01);
}
}
//显示字符串
//x,y:起点坐标
//width,height:区域大小
//size:字体大小
//*p:字符串起始地址
void LCD_ShowString(uint16_t x, uint16_t y, uint16_t width, uint16_t height, uint8_t size, uint8_t *p)
{
uint8_t x0 = x;
width += x;
height += y;
while ((*p <= '~') && (*p >= ' ')) //判断是不是非法字符!
{
if (x >= width)
{
x = x0;
y += size;
}
if (y >= height)break; //退出
LCD_ShowChar(x, y, *p, size, 0);
x += size / 2;
p++;
}
}
tftlcd.h文件
点击查看代码
#ifndef __TFTLCD_H
#define __TFTLCD_H
#include "main.h"
#include "stdlib.h"
//
//本程序只供学习使用，未经作者许可，不得用于其它任何用途
//ALIENTEK STM32开发板
//2.8寸/3.5寸/4.3寸/7寸 TFT液晶驱动
//支持驱动IC型号包括:ILI9341/NT35310/NT35510/SSD1963等
//正点原子@ALIENTEK
//技术论坛:www.openedv.com
//创建日期:2017/4/8
//版本：V4.0
//版权所有，盗版必究。
//Copyright(C) 广州市星翼电子科技有限公司 2014-2024
//All rights reserved
//*******************************************************************************
//修改说明
//V4.0 20211111
//1，去掉大部分不常用驱动IC的支持
//2，新增对ST7789驱动IC的支持
//3，优化代码结构（精简源码）
//
//LCD重要参数集
typedef struct
{
uint16_t width; //LCD 宽度
uint16_t height; //LCD 高度
uint16_t id; //LCD ID
uint8_t dir; //横屏还是竖屏控制：0，竖屏；1，横屏。
uint16_t wramcmd; //开始写gram指令
uint16_t setxcmd; //设置x坐标指令
uint16_t setycmd; //设置y坐标指令
}_lcd_dev;
//LCD参数
extern _lcd_dev lcddev; //管理LCD重要参数
//LCD的画笔颜色和背景色
extern uint32_t POINT_COLOR; //默认红色
extern uint32_t BACK_COLOR; //背景颜色.默认为白色
//
//-----------------MCU屏 LCD端口定义----------------
//LCD地址结构体
typedef struct
{
volatile uint16_t LCD_REG;
volatile uint16_t LCD_RAM;
} LCD_TypeDef;
#define LCD_BASE ((uint32_t)(0x6C000000 | 0x0000007E))
#define LCD ((LCD_TypeDef *) LCD_BASE)
//
//LCD分辨率设置
#define SSD_HOR_RESOLUTION 800 //LCD水平分辨率
#define SSD_VER_RESOLUTION 480 //LCD垂直分辨率
//扫描方向定义
#define L2R_U2D 0 //从左到右,从上到下
#define L2R_D2U 1 //从左到右,从下到上
#define R2L_U2D 2 //从右到左,从上到下
#define R2L_D2U 3 //从右到左,从下到上
#define U2D_L2R 4 //从上到下,从左到右
#define U2D_R2L 5 //从上到下,从右到左
#define D2U_L2R 6 //从下到上,从左到右
#define D2U_R2L 7 //从下到上,从右到左
#define DFT_SCAN_DIR L2R_U2D //默认的扫描方向
//画笔颜色
#define WHITE 0xFFFF
#define BLACK 0x0000
#define BLUE 0x001F
#define BRED 0XF81F
#define GRED 0XFFE0
#define GBLUE 0X07FF
#define RED 0xF800
#define MAGENTA 0xF81F
#define GREEN 0x07E0
#define CYAN 0x7FFF
#define YELLOW 0xFFE0
#define BROWN 0XBC40 //棕色
#define BRRED 0XFC07 //棕红色
#define GRAY 0X8430 //灰色
//GUI颜色
#define DARKBLUE 0X01CF //深蓝色
#define LIGHTBLUE 0X7D7C //浅蓝色
#define GRAYBLUE 0X5458 //灰蓝色
//以上三色为PANEL的颜色
#define LIGHTGREEN 0X841F //浅绿色
#define LGRAY 0XC618 //浅灰色(PANNEL),窗体背景色
#define LGRAYBLUE 0XA651 //浅灰蓝色(中间层颜色)
#define LBBLUE 0X2B12 //浅棕蓝色(选择条目的反色)
/*应用函数*/
//初始化
void LCD_Init(void);
//开显示
void LCD_DisplayOn(void);
//关显示
void LCD_DisplayOff(void);
//清屏
void LCD_Clear(uint32_t Color);
//设置光标
void LCD_SetCursor(uint16_t Xpos, uint16_t Ypos);
//画点
void LCD_DrawPoint(uint16_t x,uint16_t y);
//快速画点
void LCD_Fast_DrawPoint(uint16_t x,uint16_t y,uint32_t color);
//读点
uint32_t LCD_ReadPoint(uint16_t x,uint16_t y);
//画圆
void LCD_Draw_Circle(uint16_t x0,uint16_t y0,uint8_t r);
//画线
void LCD_DrawLine(uint16_t x1, uint16_t y1, uint16_t x2, uint16_t y2);
//画矩形
void LCD_DrawRectangle(uint16_t x1, uint16_t y1, uint16_t x2, uint16_t y2);
//填充单色
void LCD_Fill(uint16_t sx,uint16_t sy,uint16_t ex,uint16_t ey,uint32_t color);
//填充指定颜色
void LCD_Color_Fill(uint16_t sx,uint16_t sy,uint16_t ex,uint16_t ey,uint16_t *color);
//显示一个字符
void LCD_ShowChar(uint16_t x,uint16_t y,uint8_t num,uint8_t size,uint8_t mode);
//显示一个数字
void LCD_ShowNum(uint16_t x,uint16_t y,uint32_t num,uint8_t len,uint8_t size);
//显示 数字
void LCD_ShowxNum(uint16_t x,uint16_t y,uint32_t num,uint8_t len,uint8_t size,uint8_t mode);
//显示一个字符串,12/16字体
void LCD_ShowString(uint16_t x,uint16_t y,uint16_t width,uint16_t height,uint8_t size,uint8_t *p);
/*底层函数*/
void LCD_WriteReg(uint16_t LCD_Reg, uint16_t LCD_RegValue);
uint16_t LCD_ReadReg(uint16_t LCD_Reg);
void LCD_WriteRAM_Prepare(void);
void LCD_WriteRAM(uint16_t RGB_Code);
//SSD1963 背光控制
void LCD_SSD_BackLightSet(uint8_t pwm);
//设置屏扫描方向
void LCD_Scan_Dir(uint8_t dir);
//设置屏幕显示方向
void LCD_Display_Dir(uint8_t dir);
//设置窗口
void LCD_Set_Window(uint16_t sx,uint16_t sy,uint16_t width,uint16_t height);
//LCD驱动参数设置
#define SSD_HOR_PULSE_WIDTH 1 //水平脉宽
#define SSD_HOR_BACK_PORCH 46 //水平前廊
#define SSD_HOR_FRONT_PORCH 210 //水平后廊
#define SSD_VER_PULSE_WIDTH 1 //垂直脉宽
#define SSD_VER_BACK_PORCH 23 //垂直前廊
#define SSD_VER_FRONT_PORCH 22 //垂直前廊
//如下几个参数，自动计算
#define SSD_HT (SSD_HOR_RESOLUTION+SSD_HOR_BACK_PORCH+SSD_HOR_FRONT_PORCH)
#define SSD_HPS (SSD_HOR_BACK_PORCH)
#define SSD_VT (SSD_VER_RESOLUTION+SSD_VER_BACK_PORCH+SSD_VER_FRONT_PORCH)
#define SSD_VPS (SSD_VER_BACK_PORCH)
#endif
font.h文件
点击查看代码
#ifndef __FONT_H
#define __FONT_H
//常用ASCII表
//偏移量32
//ASCII字符集: !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~
//PC2LCD2002取模方式设置：阴码+逐列式+顺向+C51格式
//总共：3个字符集（12*12、16*16、24*24和32*32），用户可以自行新增其他分辨率的字符集。
//每个字符所占用的字节数为:(size/8+((size%8)?1:0))*(size/2),其中size:是字库生成时的点阵大小(12/16/24/32...)
//12*12 ASCII字符集点阵
const unsigned char asc2_1206[95][12]={
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x00,0x3F,0x40,0x00,0x00,0x00,0x00,0x00,0x00},/*"!",1*/
{0x00,0x00,0x30,0x00,0x40,0x00,0x30,0x00,0x40,0x00,0x00,0x00},/*""",2*/
{0x09,0x00,0x0B,0xC0,0x3D,0x00,0x0B,0xC0,0x3D,0x00,0x09,0x00},/*"#",3*/
{0x18,0xC0,0x24,0x40,0x7F,0xE0,0x22,0x40,0x31,0x80,0x00,0x00},/*"$",4*/
{0x18,0x00,0x24,0xC0,0x1B,0x00,0x0D,0x80,0x32,0x40,0x01,0x80},/*"%",5*/
{0x03,0x80,0x1C,0x40,0x27,0x40,0x1C,0x80,0x07,0x40,0x00,0x40},/*"&",6*/
{0x10,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0x80,0x20,0x40,0x40,0x20},/*"(",8*/
{0x00,0x00,0x40,0x20,0x20,0x40,0x1F,0x80,0x00,0x00,0x00,0x00},/*")",9*/
{0x09,0x00,0x06,0x00,0x1F,0x80,0x06,0x00,0x09,0x00,0x00,0x00},/*"*",10*/
{0x04,0x00,0x04,0x00,0x3F,0x80,0x04,0x00,0x04,0x00,0x00,0x00},/*"+",11*/
{0x00,0x10,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*",",12*/
{0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x00,0x00},/*"-",13*/
{0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x20,0x01,0xC0,0x06,0x00,0x38,0x00,0x40,0x00,0x00,0x00},/*"/",15*/
{0x1F,0x80,0x20,0x40,0x20,0x40,0x20,0x40,0x1F,0x80,0x00,0x00},/*"0",16*/
{0x00,0x00,0x10,0x40,0x3F,0xC0,0x00,0x40,0x00,0x00,0x00,0x00},/*"1",17*/
{0x18,0xC0,0x21,0x40,0x22,0x40,0x24,0x40,0x18,0x40,0x00,0x00},/*"2",18*/
{0x10,0x80,0x20,0x40,0x24,0x40,0x24,0x40,0x1B,0x80,0x00,0x00},/*"3",19*/
{0x02,0x00,0x0D,0x00,0x11,0x00,0x3F,0xC0,0x01,0x40,0x00,0x00},/*"4",20*/
{0x3C,0x80,0x24,0x40,0x24,0x40,0x24,0x40,0x23,0x80,0x00,0x00},/*"5",21*/
{0x1F,0x80,0x24,0x40,0x24,0x40,0x34,0x40,0x03,0x80,0x00,0x00},/*"6",22*/
{0x30,0x00,0x20,0x00,0x27,0xC0,0x38,0x00,0x20,0x00,0x00,0x00},/*"7",23*/
{0x1B,0x80,0x24,0x40,0x24,0x40,0x24,0x40,0x1B,0x80,0x00,0x00},/*"8",24*/
{0x1C,0x00,0x22,0xC0,0x22,0x40,0x22,0x40,0x1F,0x80,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x08,0x40,0x00,0x00,0x00,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x04,0x60,0x00,0x00,0x00,0x00,0x00,0x00},/*";",27*/
{0x00,0x00,0x04,0x00,0x0A,0x00,0x11,0x00,0x20,0x80,0x40,0x40},/*"<",28*/
{0x09,0x00,0x09,0x00,0x09,0x00,0x09,0x00,0x09,0x00,0x00,0x00},/*"=",29*/
{0x00,0x00,0x40,0x40,0x20,0x80,0x11,0x00,0x0A,0x00,0x04,0x00},/*">",30*/
{0x18,0x00,0x20,0x00,0x23,0x40,0x24,0x00,0x18,0x00,0x00,0x00},/*"?",31*/
{0x1F,0x80,0x20,0x40,0x27,0x40,0x29,0x40,0x1F,0x40,0x00,0x00},/*"@",32*/
{0x00,0x40,0x07,0xC0,0x39,0x00,0x0F,0x00,0x01,0xC0,0x00,0x40},/*"A",33*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x24,0x40,0x1B,0x80,0x00,0x00},/*"B",34*/
{0x1F,0x80,0x20,0x40,0x20,0x40,0x20,0x40,0x30,0x80,0x00,0x00},/*"C",35*/
{0x20,0x40,0x3F,0xC0,0x20,0x40,0x20,0x40,0x1F,0x80,0x00,0x00},/*"D",36*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x2E,0x40,0x30,0xC0,0x00,0x00},/*"E",37*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x2E,0x00,0x30,0x00,0x00,0x00},/*"F",38*/
{0x0F,0x00,0x10,0x80,0x20,0x40,0x22,0x40,0x33,0x80,0x02,0x00},/*"G",39*/
{0x20,0x40,0x3F,0xC0,0x04,0x00,0x04,0x00,0x3F,0xC0,0x20,0x40},/*"H",40*/
{0x20,0x40,0x20,0x40,0x3F,0xC0,0x20,0x40,0x20,0x40,0x00,0x00},/*"I",41*/
{0x00,0x60,0x20,0x20,0x20,0x20,0x3F,0xC0,0x20,0x00,0x20,0x00},/*"J",42*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x0B,0x00,0x30,0xC0,0x20,0x40},/*"K",43*/
{0x20,0x40,0x3F,0xC0,0x20,0x40,0x00,0x40,0x00,0x40,0x00,0xC0},/*"L",44*/
{0x3F,0xC0,0x3C,0x00,0x03,0xC0,0x3C,0x00,0x3F,0xC0,0x00,0x00},/*"M",45*/
{0x20,0x40,0x3F,0xC0,0x0C,0x40,0x23,0x00,0x3F,0xC0,0x20,0x00},/*"N",46*/
{0x1F,0x80,0x20,0x40,0x20,0x40,0x20,0x40,0x1F,0x80,0x00,0x00},/*"O",47*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x24,0x00,0x18,0x00,0x00,0x00},/*"P",48*/
{0x1F,0x80,0x21,0x40,0x21,0x40,0x20,0xE0,0x1F,0xA0,0x00,0x00},/*"Q",49*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x26,0x00,0x19,0xC0,0x00,0x40},/*"R",50*/
{0x18,0xC0,0x24,0x40,0x24,0x40,0x22,0x40,0x31,0x80,0x00,0x00},/*"S",51*/
{0x30,0x00,0x20,0x40,0x3F,0xC0,0x20,0x40,0x30,0x00,0x00,0x00},/*"T",52*/
{0x20,0x00,0x3F,0x80,0x00,0x40,0x00,0x40,0x3F,0x80,0x20,0x00},/*"U",53*/
{0x20,0x00,0x3E,0x00,0x01,0xC0,0x07,0x00,0x38,0x00,0x20,0x00},/*"V",54*/
{0x38,0x00,0x07,0xC0,0x3C,0x00,0x07,0xC0,0x38,0x00,0x00,0x00},/*"W",55*/
{0x20,0x40,0x39,0xC0,0x06,0x00,0x39,0xC0,0x20,0x40,0x00,0x00},/*"X",56*/
{0x20,0x00,0x38,0x40,0x07,0xC0,0x38,0x40,0x20,0x00,0x00,0x00},/*"Y",57*/
{0x30,0x40,0x21,0xC0,0x26,0x40,0x38,0x40,0x20,0xC0,0x00,0x00},/*"Z",58*/
{0x00,0x00,0x00,0x00,0x7F,0xE0,0x40,0x20,0x40,0x20,0x00,0x00},/*"[",59*/
{0x00,0x00,0x70,0x00,0x0C,0x00,0x03,0x80,0x00,0x40,0x00,0x00},/*"\",60*/
{0x00,0x00,0x40,0x20,0x40,0x20,0x7F,0xE0,0x00,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x20,0x00,0x40,0x00,0x20,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10},/*"_",63*/
{0x00,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x02,0x80,0x05,0x40,0x05,0x40,0x03,0xC0,0x00,0x40},/*"a",65*/
{0x20,0x00,0x3F,0xC0,0x04,0x40,0x04,0x40,0x03,0x80,0x00,0x00},/*"b",66*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x04,0x40,0x06,0x40,0x00,0x00},/*"c",67*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x24,0x40,0x3F,0xC0,0x00,0x40},/*"d",68*/
{0x00,0x00,0x03,0x80,0x05,0x40,0x05,0x40,0x03,0x40,0x00,0x00},/*"e",69*/
{0x00,0x00,0x04,0x40,0x1F,0xC0,0x24,0x40,0x24,0x40,0x20,0x00},/*"f",70*/
{0x00,0x00,0x02,0xE0,0x05,0x50,0x05,0x50,0x06,0x50,0x04,0x20},/*"g",71*/
{0x20,0x40,0x3F,0xC0,0x04,0x40,0x04,0x00,0x03,0xC0,0x00,0x40},/*"h",72*/
{0x00,0x00,0x04,0x40,0x27,0xC0,0x00,0x40,0x00,0x00,0x00,0x00},/*"i",73*/
{0x00,0x10,0x00,0x10,0x04,0x10,0x27,0xE0,0x00,0x00,0x00,0x00},/*"j",74*/
{0x20,0x40,0x3F,0xC0,0x01,0x40,0x07,0x00,0x04,0xC0,0x04,0x40},/*"k",75*/
{0x20,0x40,0x20,0x40,0x3F,0xC0,0x00,0x40,0x00,0x40,0x00,0x00},/*"l",76*/
{0x07,0xC0,0x04,0x00,0x07,0xC0,0x04,0x00,0x03,0xC0,0x00,0x00},/*"m",77*/
{0x04,0x40,0x07,0xC0,0x04,0x40,0x04,0x00,0x03,0xC0,0x00,0x40},/*"n",78*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x04,0x40,0x03,0x80,0x00,0x00},/*"o",79*/
{0x04,0x10,0x07,0xF0,0x04,0x50,0x04,0x40,0x03,0x80,0x00,0x00},/*"p",80*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x04,0x50,0x07,0xF0,0x00,0x10},/*"q",81*/
{0x04,0x40,0x07,0xC0,0x02,0x40,0x04,0x00,0x04,0x00,0x00,0x00},/*"r",82*/
{0x00,0x00,0x06,0x40,0x05,0x40,0x05,0x40,0x04,0xC0,0x00,0x00},/*"s",83*/
{0x00,0x00,0x04,0x00,0x1F,0x80,0x04,0x40,0x00,0x40,0x00,0x00},/*"t",84*/
{0x04,0x00,0x07,0x80,0x00,0x40,0x04,0x40,0x07,0xC0,0x00,0x40},/*"u",85*/
{0x04,0x00,0x07,0x00,0x04,0xC0,0x01,0x80,0x06,0x00,0x04,0x00},/*"v",86*/
{0x06,0x00,0x01,0xC0,0x07,0x00,0x01,0xC0,0x06,0x00,0x00,0x00},/*"w",87*/
{0x04,0x40,0x06,0xC0,0x01,0x00,0x06,0xC0,0x04,0x40,0x00,0x00},/*"x",88*/
{0x04,0x10,0x07,0x10,0x04,0xE0,0x01,0x80,0x06,0x00,0x04,0x00},/*"y",89*/
{0x00,0x00,0x04,0x40,0x05,0xC0,0x06,0x40,0x04,0x40,0x00,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x04,0x00,0x7B,0xE0,0x40,0x20,0x00,0x00},/*"{",91*/
{0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xF0,0x00,0x00,0x00,0x00},/*"|",92*/
{0x00,0x00,0x40,0x20,0x7B,0xE0,0x04,0x00,0x00,0x00,0x00,0x00},/*"}",93*/
{0x40,0x00,0x80,0x00,0x40,0x00,0x20,0x00,0x20,0x00,0x40,0x00},/*"~",94*/
};
//16*16 ASCII字符集点阵
const unsigned char asc2_1608[95][16]={
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0xCC,0x00,0x0C,0x00,0x00,0x00,0x00,0x00,0x00},/*"!",1*/
{0x00,0x00,0x08,0x00,0x30,0x00,0x60,0x00,0x08,0x00,0x30,0x00,0x60,0x00,0x00,0x00},/*""",2*/
{0x02,0x20,0x03,0xFC,0x1E,0x20,0x02,0x20,0x03,0xFC,0x1E,0x20,0x02,0x20,0x00,0x00},/*"#",3*/
{0x00,0x00,0x0E,0x18,0x11,0x04,0x3F,0xFF,0x10,0x84,0x0C,0x78,0x00,0x00,0x00,0x00},/*"$",4*/
{0x0F,0x00,0x10,0x84,0x0F,0x38,0x00,0xC0,0x07,0x78,0x18,0x84,0x00,0x78,0x00,0x00},/*"%",5*/
{0x00,0x78,0x0F,0x84,0x10,0xC4,0x11,0x24,0x0E,0x98,0x00,0xE4,0x00,0x84,0x00,0x08},/*"&",6*/
{0x08,0x00,0x68,0x00,0x70,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x07,0xE0,0x18,0x18,0x20,0x04,0x40,0x02,0x00,0x00},/*"(",8*/
{0x00,0x00,0x40,0x02,0x20,0x04,0x18,0x18,0x07,0xE0,0x00,0x00,0x00,0x00,0x00,0x00},/*")",9*/
{0x02,0x40,0x02,0x40,0x01,0x80,0x0F,0xF0,0x01,0x80,0x02,0x40,0x02,0x40,0x00,0x00},/*"*",10*/
{0x00,0x80,0x00,0x80,0x00,0x80,0x0F,0xF8,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x00},/*"+",11*/
{0x00,0x01,0x00,0x0D,0x00,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*",",12*/
{0x00,0x00,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80},/*"-",13*/
{0x00,0x00,0x00,0x0C,0x00,0x0C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x00,0x00,0x06,0x00,0x18,0x00,0x60,0x01,0x80,0x06,0x00,0x18,0x00,0x20,0x00},/*"/",15*/
{0x00,0x00,0x07,0xF0,0x08,0x08,0x10,0x04,0x10,0x04,0x08,0x08,0x07,0xF0,0x00,0x00},/*"0",16*/
{0x00,0x00,0x08,0x04,0x08,0x04,0x1F,0xFC,0x00,0x04,0x00,0x04,0x00,0x00,0x00,0x00},/*"1",17*/
{0x00,0x00,0x0E,0x0C,0x10,0x14,0x10,0x24,0x10,0x44,0x11,0x84,0x0E,0x0C,0x00,0x00},/*"2",18*/
{0x00,0x00,0x0C,0x18,0x10,0x04,0x11,0x04,0x11,0x04,0x12,0x88,0x0C,0x70,0x00,0x00},/*"3",19*/
{0x00,0x00,0x00,0xE0,0x03,0x20,0x04,0x24,0x08,0x24,0x1F,0xFC,0x00,0x24,0x00,0x00},/*"4",20*/
{0x00,0x00,0x1F,0x98,0x10,0x84,0x11,0x04,0x11,0x04,0x10,0x88,0x10,0x70,0x00,0x00},/*"5",21*/
{0x00,0x00,0x07,0xF0,0x08,0x88,0x11,0x04,0x11,0x04,0x18,0x88,0x00,0x70,0x00,0x00},/*"6",22*/
{0x00,0x00,0x1C,0x00,0x10,0x00,0x10,0xFC,0x13,0x00,0x1C,0x00,0x10,0x00,0x00,0x00},/*"7",23*/
{0x00,0x00,0x0E,0x38,0x11,0x44,0x10,0x84,0x10,0x84,0x11,0x44,0x0E,0x38,0x00,0x00},/*"8",24*/
{0x00,0x00,0x07,0x00,0x08,0x8C,0x10,0x44,0x10,0x44,0x08,0x88,0x07,0xF0,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x0C,0x03,0x0C,0x00,0x00,0x00,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*";",27*/
{0x00,0x00,0x00,0x80,0x01,0x40,0x02,0x20,0x04,0x10,0x08,0x08,0x10,0x04,0x00,0x00},/*"<",28*/
{0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x00,0x00},/*"=",29*/
{0x00,0x00,0x10,0x04,0x08,0x08,0x04,0x10,0x02,0x20,0x01,0x40,0x00,0x80,0x00,0x00},/*">",30*/
{0x00,0x00,0x0E,0x00,0x12,0x00,0x10,0x0C,0x10,0x6C,0x10,0x80,0x0F,0x00,0x00,0x00},/*"?",31*/
{0x03,0xE0,0x0C,0x18,0x13,0xE4,0x14,0x24,0x17,0xC4,0x08,0x28,0x07,0xD0,0x00,0x00},/*"@",32*/
{0x00,0x04,0x00,0x3C,0x03,0xC4,0x1C,0x40,0x07,0x40,0x00,0xE4,0x00,0x1C,0x00,0x04},/*"A",33*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x04,0x11,0x04,0x0E,0x88,0x00,0x70,0x00,0x00},/*"B",34*/
{0x03,0xE0,0x0C,0x18,0x10,0x04,0x10,0x04,0x10,0x04,0x10,0x08,0x1C,0x10,0x00,0x00},/*"C",35*/
{0x10,0x04,0x1F,0xFC,0x10,0x04,0x10,0x04,0x10,0x04,0x08,0x08,0x07,0xF0,0x00,0x00},/*"D",36*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x04,0x17,0xC4,0x10,0x04,0x08,0x18,0x00,0x00},/*"E",37*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x00,0x17,0xC0,0x10,0x00,0x08,0x00,0x00,0x00},/*"F",38*/
{0x03,0xE0,0x0C,0x18,0x10,0x04,0x10,0x04,0x10,0x44,0x1C,0x78,0x00,0x40,0x00,0x00},/*"G",39*/
{0x10,0x04,0x1F,0xFC,0x10,0x84,0x00,0x80,0x00,0x80,0x10,0x84,0x1F,0xFC,0x10,0x04},/*"H",40*/
{0x00,0x00,0x10,0x04,0x10,0x04,0x1F,0xFC,0x10,0x04,0x10,0x04,0x00,0x00,0x00,0x00},/*"I",41*/
{0x00,0x03,0x00,0x01,0x10,0x01,0x10,0x01,0x1F,0xFE,0x10,0x00,0x10,0x00,0x00,0x00},/*"J",42*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x03,0x80,0x14,0x64,0x18,0x1C,0x10,0x04,0x00,0x00},/*"K",43*/
{0x10,0x04,0x1F,0xFC,0x10,0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x0C,0x00,0x00},/*"L",44*/
{0x10,0x04,0x1F,0xFC,0x1F,0x00,0x00,0xFC,0x1F,0x00,0x1F,0xFC,0x10,0x04,0x00,0x00},/*"M",45*/
{0x10,0x04,0x1F,0xFC,0x0C,0x04,0x03,0x00,0x00,0xE0,0x10,0x18,0x1F,0xFC,0x10,0x00},/*"N",46*/
{0x07,0xF0,0x08,0x08,0x10,0x04,0x10,0x04,0x10,0x04,0x08,0x08,0x07,0xF0,0x00,0x00},/*"O",47*/
{0x10,0x04,0x1F,0xFC,0x10,0x84,0x10,0x80,0x10,0x80,0x10,0x80,0x0F,0x00,0x00,0x00},/*"P",48*/
{0x07,0xF0,0x08,0x18,0x10,0x24,0x10,0x24,0x10,0x1C,0x08,0x0A,0x07,0xF2,0x00,0x00},/*"Q",49*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x00,0x11,0xC0,0x11,0x30,0x0E,0x0C,0x00,0x04},/*"R",50*/
{0x00,0x00,0x0E,0x1C,0x11,0x04,0x10,0x84,0x10,0x84,0x10,0x44,0x1C,0x38,0x00,0x00},/*"S",51*/
{0x18,0x00,0x10,0x00,0x10,0x04,0x1F,0xFC,0x10,0x04,0x10,0x00,0x18,0x00,0x00,0x00},/*"T",52*/
{0x10,0x00,0x1F,0xF8,0x10,0x04,0x00,0x04,0x00,0x04,0x10,0x04,0x1F,0xF8,0x10,0x00},/*"U",53*/
{0x10,0x00,0x1E,0x00,0x11,0xE0,0x00,0x1C,0x00,0x70,0x13,0x80,0x1C,0x00,0x10,0x00},/*"V",54*/
{0x1F,0xC0,0x10,0x3C,0x00,0xE0,0x1F,0x00,0x00,0xE0,0x10,0x3C,0x1F,0xC0,0x00,0x00},/*"W",55*/
{0x10,0x04,0x18,0x0C,0x16,0x34,0x01,0xC0,0x01,0xC0,0x16,0x34,0x18,0x0C,0x10,0x04},/*"X",56*/
{0x10,0x00,0x1C,0x00,0x13,0x04,0x00,0xFC,0x13,0x04,0x1C,0x00,0x10,0x00,0x00,0x00},/*"Y",57*/
{0x08,0x04,0x10,0x1C,0x10,0x64,0x10,0x84,0x13,0x04,0x1C,0x04,0x10,0x18,0x00,0x00},/*"Z",58*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFE,0x40,0x02,0x40,0x02,0x40,0x02,0x00,0x00},/*"[",59*/
{0x00,0x00,0x30,0x00,0x0C,0x00,0x03,0x80,0x00,0x60,0x00,0x1C,0x00,0x03,0x00,0x00},/*"\",60*/
{0x00,0x00,0x40,0x02,0x40,0x02,0x40,0x02,0x7F,0xFE,0x00,0x00,0x00,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x20,0x00,0x00,0x00},/*"^",62*/
{0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01},/*"_",63*/
{0x00,0x00,0x40,0x00,0x40,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x00,0x98,0x01,0x24,0x01,0x44,0x01,0x44,0x01,0x44,0x00,0xFC,0x00,0x04},/*"a",65*/
{0x10,0x00,0x1F,0xFC,0x00,0x88,0x01,0x04,0x01,0x04,0x00,0x88,0x00,0x70,0x00,0x00},/*"b",66*/
{0x00,0x00,0x00,0x70,0x00,0x88,0x01,0x04,0x01,0x04,0x01,0x04,0x00,0x88,0x00,0x00},/*"c",67*/
{0x00,0x00,0x00,0x70,0x00,0x88,0x01,0x04,0x01,0x04,0x11,0x08,0x1F,0xFC,0x00,0x04},/*"d",68*/
{0x00,0x00,0x00,0xF8,0x01,0x44,0x01,0x44,0x01,0x44,0x01,0x44,0x00,0xC8,0x00,0x00},/*"e",69*/
{0x00,0x00,0x01,0x04,0x01,0x04,0x0F,0xFC,0x11,0x04,0x11,0x04,0x11,0x00,0x18,0x00},/*"f",70*/
{0x00,0x00,0x00,0xD6,0x01,0x29,0x01,0x29,0x01,0x29,0x01,0xC9,0x01,0x06,0x00,0x00},/*"g",71*/
{0x10,0x04,0x1F,0xFC,0x00,0x84,0x01,0x00,0x01,0x00,0x01,0x04,0x00,0xFC,0x00,0x04},/*"h",72*/
{0x00,0x00,0x01,0x04,0x19,0x04,0x19,0xFC,0x00,0x04,0x00,0x04,0x00,0x00,0x00,0x00},/*"i",73*/
{0x00,0x00,0x00,0x03,0x00,0x01,0x01,0x01,0x19,0x01,0x19,0xFE,0x00,0x00,0x00,0x00},/*"j",74*/
{0x10,0x04,0x1F,0xFC,0x00,0x24,0x00,0x40,0x01,0xB4,0x01,0x0C,0x01,0x04,0x00,0x00},/*"k",75*/
{0x00,0x00,0x10,0x04,0x10,0x04,0x1F,0xFC,0x00,0x04,0x00,0x04,0x00,0x00,0x00,0x00},/*"l",76*/
{0x01,0x04,0x01,0xFC,0x01,0x04,0x01,0x00,0x01,0xFC,0x01,0x04,0x01,0x00,0x00,0xFC},/*"m",77*/
{0x01,0x04,0x01,0xFC,0x00,0x84,0x01,0x00,0x01,0x00,0x01,0x04,0x00,0xFC,0x00,0x04},/*"n",78*/
{0x00,0x00,0x00,0xF8,0x01,0x04,0x01,0x04,0x01,0x04,0x01,0x04,0x00,0xF8,0x00,0x00},/*"o",79*/
{0x01,0x01,0x01,0xFF,0x00,0x85,0x01,0x04,0x01,0x04,0x00,0x88,0x00,0x70,0x00,0x00},/*"p",80*/
{0x00,0x00,0x00,0x70,0x00,0x88,0x01,0x04,0x01,0x04,0x01,0x05,0x01,0xFF,0x00,0x01},/*"q",81*/
{0x01,0x04,0x01,0x04,0x01,0xFC,0x00,0x84,0x01,0x04,0x01,0x00,0x01,0x80,0x00,0x00},/*"r",82*/
{0x00,0x00,0x00,0xCC,0x01,0x24,0x01,0x24,0x01,0x24,0x01,0x24,0x01,0x98,0x00,0x00},/*"s",83*/
{0x00,0x00,0x01,0x00,0x01,0x00,0x07,0xF8,0x01,0x04,0x01,0x04,0x00,0x00,0x00,0x00},/*"t",84*/
{0x01,0x00,0x01,0xF8,0x00,0x04,0x00,0x04,0x00,0x04,0x01,0x08,0x01,0xFC,0x00,0x04},/*"u",85*/
{0x01,0x00,0x01,0x80,0x01,0x70,0x00,0x0C,0x00,0x10,0x01,0x60,0x01,0x80,0x01,0x00},/*"v",86*/
{0x01,0xF0,0x01,0x0C,0x00,0x30,0x01,0xC0,0x00,0x30,0x01,0x0C,0x01,0xF0,0x01,0x00},/*"w",87*/
{0x00,0x00,0x01,0x04,0x01,0x8C,0x00,0x74,0x01,0x70,0x01,0x8C,0x01,0x04,0x00,0x00},/*"x",88*/
{0x01,0x01,0x01,0x81,0x01,0x71,0x00,0x0E,0x00,0x18,0x01,0x60,0x01,0x80,0x01,0x00},/*"y",89*/
{0x00,0x00,0x01,0x84,0x01,0x0C,0x01,0x34,0x01,0x44,0x01,0x84,0x01,0x0C,0x00,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x3E,0xFC,0x40,0x02,0x40,0x02},/*"{",91*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00},/*"|",92*/
{0x00,0x00,0x40,0x02,0x40,0x02,0x3E,0xFC,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"}",93*/
{0x00,0x00,0x60,0x00,0x80,0x00,0x80,0x00,0x40,0x00,0x40,0x00,0x20,0x00,0x20,0x00},/*"~",94*/
};
//24*24 ASICII字符集点阵
const unsigned char asc2_2412[95][36]={
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0x80,0x38,0x0F,0xFE,0x38,0x0F,0x80,0x38,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"!",1*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x00,0x06,0x00,0x00,0x0C,0x00,0x00,0x38,0x00,0x00,0x31,0x00,0x00,0x06,0x00,0x00,0x0C,0x00,0x00,0x38,0x00,0x00,0x30,0x00,0x00,0x00,0x00,0x00},/*""",2*/
{0x00,0x00,0x00,0x00,0x61,0x80,0x00,0x67,0xF8,0x07,0xF9,0x80,0x00,0x61,0x80,0x00,0x61,0x80,0x00,0x61,0x80,0x00,0x61,0x80,0x00,0x67,0xF8,0x07,0xF9,0x80,0x00,0x61,0x80,0x00,0x00,0x00},/*"#",3*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x01,0xC0,0xE0,0x03,0xE0,0xF0,0x06,0x30,0x08,0x04,0x18,0x08,0x1F,0xFF,0xFE,0x04,0x0E,0x08,0x07,0x87,0xF0,0x03,0x81,0xE0,0x00,0x00,0x00,0x00,0x00,0x00},/*"$",4*/
{0x01,0xF0,0x00,0x06,0x0C,0x00,0x04,0x04,0x08,0x06,0x0C,0x70,0x01,0xF9,0xC0,0x00,0x0E,0x00,0x00,0x3B,0xE0,0x00,0xEC,0x18,0x07,0x08,0x08,0x04,0x0C,0x18,0x00,0x03,0xE0,0x00,0x00,0x00},/*"%",5*/
{0x00,0x01,0xE0,0x00,0x07,0xF0,0x03,0xF8,0x18,0x04,0x1C,0x08,0x04,0x17,0x08,0x07,0xE1,0xD0,0x03,0xC0,0xE0,0x00,0x23,0xB0,0x00,0x3C,0x08,0x00,0x20,0x08,0x00,0x00,0x10,0x00,0x00,0x00},/*"&",6*/
{0x00,0x00,0x00,0x01,0x00,0x00,0x31,0x00,0x00,0x32,0x00,0x00,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x00,0x01,0xFF,0xC0,0x07,0x80,0xF0,0x0C,0x00,0x18,0x10,0x00,0x04,0x20,0x00,0x02,0x00,0x00,0x00},/*"(",8*/
{0x00,0x00,0x00,0x20,0x00,0x02,0x10,0x00,0x04,0x0C,0x00,0x18,0x07,0x80,0xF0,0x01,0xFF,0xC0,0x00,0x7F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*")",9*/
{0x00,0x00,0x00,0x00,0x42,0x00,0x00,0x66,0x00,0x00,0x66,0x00,0x00,0x3C,0x00,0x00,0x18,0x00,0x03,0xFF,0xC0,0x00,0x18,0x00,0x00,0x3C,0x00,0x00,0x66,0x00,0x00,0x66,0x00,0x00,0x42,0x00},/*"*",10*/
{0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x01,0xFF,0xC0,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00},/*"+",11*/
{0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x00,0x31,0x00,0x00,0x32,0x00,0x00,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*",",12*/
{0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x00,0x00},/*"-",13*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x38,0x00,0x00,0x38,0x00,0x00,0x38,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x00,0x00,0x00,0x00,0x06,0x00,0x00,0x1C,0x00,0x00,0x70,0x00,0x01,0x80,0x00,0x0E,0x00,0x00,0x38,0x00,0x00,0xC0,0x00,0x07,0x00,0x00,0x1C,0x00,0x00,0x30,0x00,0x00,0x00,0x00,0x00},/*"/",15*/
{0x00,0x00,0x00,0x00,0x7F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x06,0x00,0x18,0x04,0x00,0x08,0x04,0x00,0x08,0x06,0x00,0x18,0x03,0x80,0x70,0x01,0xFF,0xE0,0x00,0x7F,0x80,0x00,0x00,0x00},/*"0",16*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x08,0x01,0x00,0x08,0x01,0x00,0x08,0x03,0xFF,0xF8,0x07,0xFF,0xF8,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00},/*"1",17*/
{0x00,0x00,0x00,0x01,0xC0,0x38,0x02,0xC0,0x58,0x04,0x00,0x98,0x04,0x01,0x18,0x04,0x02,0x18,0x04,0x04,0x18,0x06,0x1C,0x18,0x03,0xF8,0x18,0x01,0xE0,0xF8,0x00,0x00,0x00,0x00,0x00,0x00},/*"2",18*/
{0x00,0x00,0x00,0x01,0xC0,0xE0,0x03,0xC0,0xF0,0x04,0x00,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x06,0x18,0x08,0x03,0xF4,0x18,0x01,0xE7,0xF0,0x00,0x01,0xE0,0x00,0x00,0x00,0x00,0x00,0x00},/*"3",19*/
{0x00,0x00,0x00,0x00,0x03,0x00,0x00,0x0D,0x00,0x00,0x11,0x00,0x00,0x61,0x00,0x00,0x81,0x08,0x03,0x01,0x08,0x07,0xFF,0xF8,0x0F,0xFF,0xF8,0x00,0x01,0x08,0x00,0x01,0x08,0x00,0x00,0x00},/*"4",20*/
{0x00,0x00,0x00,0x00,0x00,0xE0,0x07,0xFC,0xD0,0x06,0x08,0x08,0x06,0x10,0x08,0x06,0x10,0x08,0x06,0x10,0x08,0x06,0x18,0x38,0x06,0x0F,0xF0,0x06,0x07,0xC0,0x00,0x00,0x00,0x00,0x00,0x00},/*"5",21*/
{0x00,0x00,0x00,0x00,0x3F,0x80,0x01,0xFF,0xE0,0x03,0x84,0x30,0x02,0x08,0x18,0x04,0x10,0x08,0x04,0x10,0x08,0x04,0x10,0x08,0x07,0x18,0x10,0x03,0x0F,0xF0,0x00,0x07,0xC0,0x00,0x00,0x00},/*"6",22*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x03,0xC0,0x00,0x07,0x00,0x00,0x06,0x00,0x00,0x06,0x00,0xF8,0x06,0x07,0xF8,0x06,0x18,0x00,0x06,0xE0,0x00,0x07,0x00,0x00,0x06,0x00,0x00,0x00,0x00,0x00},/*"7",23*/
{0x00,0x00,0x00,0x01,0xE1,0xE0,0x03,0xF7,0xF0,0x06,0x34,0x10,0x04,0x18,0x08,0x04,0x18,0x08,0x04,0x0C,0x08,0x04,0x0C,0x08,0x06,0x16,0x18,0x03,0xF3,0xF0,0x01,0xC1,0xE0,0x00,0x00,0x00},/*"8",24*/
{0x00,0x00,0x00,0x00,0xF8,0x00,0x03,0xFC,0x30,0x03,0x06,0x38,0x04,0x02,0x08,0x04,0x02,0x08,0x04,0x02,0x08,0x04,0x04,0x10,0x03,0x08,0xF0,0x01,0xFF,0xC0,0x00,0x7F,0x00,0x00,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x38,0x00,0x70,0x38,0x00,0x70,0x38,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x1A,0x00,0x30,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*";",27*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x14,0x00,0x00,0x22,0x00,0x00,0x41,0x00,0x00,0x80,0x80,0x01,0x00,0x40,0x02,0x00,0x20,0x04,0x00,0x10,0x08,0x00,0x08,0x00,0x00,0x00},/*"<",28*/
{0x00,0x00,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x00,0x00},/*"=",29*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x08,0x04,0x00,0x10,0x02,0x00,0x20,0x01,0x00,0x40,0x00,0x80,0x80,0x00,0x41,0x00,0x00,0x22,0x00,0x00,0x14,0x00,0x00,0x08,0x00,0x00,0x00,0x00},/*">",30*/
{0x00,0x00,0x00,0x03,0xC0,0x00,0x04,0xC0,0x00,0x04,0x00,0x00,0x08,0x00,0x38,0x08,0x0F,0x38,0x08,0x08,0x38,0x08,0x10,0x00,0x0C,0x30,0x00,0x07,0xE0,0x00,0x03,0xC0,0x00,0x00,0x00,0x00},/*"?",31*/
{0x00,0x00,0x00,0x00,0x3F,0x80,0x00,0xFF,0xE0,0x03,0x80,0x70,0x02,0x0F,0x10,0x06,0x70,0x88,0x04,0xC0,0x88,0x04,0x83,0x08,0x04,0x7F,0x88,0x02,0xC0,0x90,0x03,0x01,0x20,0x00,0xFE,0x40},/*"@",32*/
{0x00,0x00,0x08,0x00,0x00,0x18,0x00,0x01,0xF8,0x00,0x3E,0x08,0x01,0xC2,0x00,0x07,0x02,0x00,0x07,0xE2,0x00,0x00,0xFE,0x00,0x00,0x1F,0xC8,0x00,0x01,0xF8,0x00,0x00,0x38,0x00,0x00,0x08},/*"A",33*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x06,0x18,0x08,0x03,0xF4,0x18,0x01,0xE7,0xF0,0x00,0x01,0xE0,0x00,0x00,0x00},/*"B",34*/
{0x00,0x00,0x00,0x00,0x3F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x02,0x00,0x18,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x10,0x06,0x00,0x20,0x07,0x80,0xC0,0x00,0x00,0x00},/*"C",35*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x18,0x02,0x00,0x10,0x03,0x80,0x70,0x01,0xFF,0xE0,0x00,0x7F,0x80,0x00,0x00,0x00},/*"D",36*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x3E,0x08,0x04,0x00,0x08,0x06,0x00,0x18,0x01,0x00,0x60,0x00,0x00,0x00},/*"E",37*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x04,0x08,0x00,0x04,0x08,0x00,0x04,0x08,0x00,0x04,0x3E,0x00,0x06,0x00,0x00,0x06,0x00,0x00,0x01,0x80,0x00,0x00,0x00,0x00},/*"F",38*/
{0x00,0x00,0x00,0x00,0x3F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x06,0x00,0x18,0x04,0x00,0x08,0x04,0x02,0x08,0x04,0x02,0x08,0x02,0x03,0xF0,0x07,0x83,0xF0,0x00,0x02,0x00,0x00,0x02,0x00},/*"G",39*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x04,0x08,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08},/*"H",40*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00},/*"I",41*/
{0x00,0x00,0x00,0x00,0x00,0x06,0x00,0x00,0x07,0x00,0x00,0x01,0x04,0x00,0x01,0x04,0x00,0x01,0x04,0x00,0x03,0x07,0xFF,0xFE,0x07,0xFF,0xFC,0x04,0x00,0x00,0x04,0x00,0x00,0x04,0x00,0x00},/*"J",42*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x0C,0x08,0x00,0x18,0x00,0x00,0x3E,0x00,0x04,0xC7,0x80,0x05,0x03,0xC8,0x06,0x00,0xF8,0x04,0x00,0x38,0x04,0x00,0x18,0x00,0x00,0x08},/*"K",43*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x18,0x00,0x00,0x60,0x00,0x00,0x00},/*"L",44*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0x80,0x08,0x07,0xFC,0x00,0x00,0x7F,0xC0,0x00,0x03,0xF8,0x00,0x07,0xC0,0x00,0x78,0x00,0x07,0x80,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08},/*"M",45*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0x00,0x08,0x03,0xC0,0x00,0x00,0xE0,0x00,0x00,0x38,0x00,0x00,0x1E,0x00,0x00,0x07,0x00,0x00,0x01,0xC0,0x04,0x00,0xF0,0x07,0xFF,0xF8,0x04,0x00,0x00},/*"N",46*/
{0x00,0x00,0x00,0x00,0x7F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x06,0x00,0x18,0x04,0x00,0x08,0x04,0x00,0x08,0x06,0x00,0x18,0x03,0x00,0x30,0x01,0xFF,0xE0,0x00,0x7F,0x80,0x00,0x00,0x00},/*"O",47*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x04,0x08,0x04,0x04,0x00,0x04,0x04,0x00,0x04,0x04,0x00,0x04,0x04,0x00,0x06,0x0C,0x00,0x03,0xF8,0x00,0x01,0xF0,0x00,0x00,0x00,0x00},/*"P",48*/
{0x00,0x00,0x00,0x00,0x7F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x06,0x00,0x88,0x04,0x00,0x88,0x04,0x00,0xC8,0x06,0x00,0x3C,0x03,0x00,0x3E,0x01,0xFF,0xE6,0x00,0x7F,0x84,0x00,0x00,0x00},/*"Q",49*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x04,0x08,0x00,0x04,0x0C,0x00,0x04,0x0F,0x00,0x04,0x0B,0xC0,0x06,0x10,0xF0,0x03,0xF0,0x38,0x01,0xE0,0x08,0x00,0x00,0x08},/*"R",50*/
{0x00,0x00,0x00,0x01,0xE0,0xF8,0x03,0xF0,0x30,0x06,0x30,0x10,0x04,0x18,0x08,0x04,0x18,0x08,0x04,0x0C,0x08,0x04,0x0C,0x08,0x02,0x06,0x18,0x02,0x07,0xF0,0x07,0x81,0xE0,0x00,0x00,0x00},/*"S",51*/
{0x01,0x80,0x00,0x06,0x00,0x00,0x04,0x00,0x00,0x04,0x00,0x00,0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08,0x04,0x00,0x00,0x04,0x00,0x00,0x06,0x00,0x00,0x01,0x80,0x00},/*"T",52*/
{0x04,0x00,0x00,0x07,0xFF,0xE0,0x07,0xFF,0xF0,0x04,0x00,0x18,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x04,0x00,0x10,0x07,0xFF,0xE0,0x04,0x00,0x00},/*"U",53*/
{0x04,0x00,0x00,0x06,0x00,0x00,0x07,0xE0,0x00,0x07,0xFE,0x00,0x04,0x1F,0xE0,0x00,0x01,0xF8,0x00,0x00,0x38,0x00,0x01,0xE0,0x04,0x3E,0x00,0x07,0xC0,0x00,0x06,0x00,0x00,0x04,0x00,0x00},/*"V",54*/
{0x04,0x00,0x00,0x07,0xE0,0x00,0x07,0xFF,0xC0,0x04,0x1F,0xF8,0x00,0x07,0xC0,0x07,0xF8,0x00,0x07,0xFF,0x80,0x04,0x3F,0xF8,0x00,0x07,0xC0,0x04,0xF8,0x00,0x07,0x00,0x00,0x04,0x00,0x00},/*"W",55*/
{0x00,0x00,0x00,0x04,0x00,0x08,0x06,0x00,0x18,0x07,0xC0,0x78,0x05,0xF1,0xC8,0x00,0x3E,0x00,0x00,0x1F,0x80,0x04,0x63,0xE8,0x07,0x80,0xF8,0x06,0x00,0x18,0x04,0x00,0x08,0x00,0x00,0x00},/*"X",56*/
{0x04,0x00,0x00,0x06,0x00,0x00,0x07,0x80,0x00,0x07,0xE0,0x08,0x04,0x7C,0x08,0x00,0x1F,0xF8,0x00,0x07,0xF8,0x00,0x18,0x08,0x04,0xE0,0x08,0x07,0x00,0x00,0x06,0x00,0x00,0x04,0x00,0x00},/*"Y",57*/
{0x00,0x00,0x00,0x01,0x00,0x08,0x06,0x00,0x38,0x04,0x00,0xF8,0x04,0x03,0xE8,0x04,0x0F,0x08,0x04,0x7C,0x08,0x05,0xF0,0x08,0x07,0xC0,0x08,0x07,0x00,0x18,0x04,0x00,0x60,0x00,0x00,0x00},/*"Z",58*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0xFF,0xFE,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x00,0x00,0x00},/*"[",59*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x07,0x00,0x00,0x00,0xC0,0x00,0x00,0x38,0x00,0x00,0x06,0x00,0x00,0x01,0xC0,0x00,0x00,0x30,0x00,0x00,0x0E,0x00,0x00,0x01,0x00,0x00,0x00},/*"\",60*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x3F,0xFF,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x10,0x00,0x00,0x30,0x00,0x00,0x20,0x00,0x00,0x30,0x00,0x00,0x10,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01},/*"_",63*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0x10,0x00,0x00,0x10,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x00,0x00,0x00,0xF0,0x00,0x19,0xF8,0x00,0x1B,0x18,0x00,0x22,0x08,0x00,0x26,0x08,0x00,0x24,0x08,0x00,0x24,0x10,0x00,0x3F,0xF8,0x00,0x1F,0xF8,0x00,0x00,0x08,0x00,0x00,0x18},/*"a",65*/
{0x00,0x00,0x00,0x04,0x00,0x00,0x07,0xFF,0xF8,0x0F,0xFF,0xF0,0x00,0x18,0x18,0x00,0x10,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x30,0x18,0x00,0x1F,0xF0,0x00,0x0F,0xC0,0x00,0x00,0x00},/*"b",66*/
{0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x1F,0xF0,0x00,0x18,0x30,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x3C,0x08,0x00,0x1C,0x10,0x00,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x00},/*"c",67*/
{0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x1F,0xF0,0x00,0x38,0x18,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x04,0x10,0x10,0x07,0xFF,0xF8,0x0F,0xFF,0xF0,0x00,0x00,0x10,0x00,0x00,0x00},/*"d",68*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x1F,0xF0,0x00,0x12,0x30,0x00,0x22,0x18,0x00,0x22,0x08,0x00,0x22,0x08,0x00,0x32,0x08,0x00,0x1E,0x10,0x00,0x0E,0x20,0x00,0x00,0x00},/*"e",69*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x20,0x08,0x00,0x20,0x08,0x01,0xFF,0xF8,0x03,0xFF,0xF8,0x06,0x20,0x08,0x04,0x20,0x08,0x04,0x20,0x08,0x07,0x20,0x00,0x03,0x00,0x00,0x00,0x00,0x00},/*"f",70*/
{0x00,0x00,0x00,0x00,0x00,0x0E,0x00,0x0E,0x6E,0x00,0x1F,0xF3,0x00,0x31,0xB1,0x00,0x20,0xB1,0x00,0x20,0xB1,0x00,0x31,0x91,0x00,0x1F,0x13,0x00,0x2E,0x1E,0x00,0x20,0x0E,0x00,0x30,0x00},/*"g",71*/
{0x00,0x00,0x00,0x04,0x00,0x08,0x07,0xFF,0xF8,0x0F,0xFF,0xF8,0x00,0x10,0x08,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x1F,0xF8,0x00,0x00,0x08,0x00,0x00,0x00},/*"h",72*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x06,0x3F,0xF8,0x06,0x3F,0xF8,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00},/*"i",73*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x00,0x03,0x00,0x20,0x01,0x00,0x20,0x01,0x00,0x20,0x03,0x06,0x3F,0xFE,0x06,0x3F,0xFC,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"j",74*/
{0x00,0x00,0x00,0x04,0x00,0x08,0x07,0xFF,0xF8,0x0F,0xFF,0xF8,0x00,0x01,0x88,0x00,0x03,0x00,0x00,0x2F,0xC0,0x00,0x38,0xF8,0x00,0x20,0x38,0x00,0x20,0x08,0x00,0x00,0x08,0x00,0x00,0x00},/*"k",75*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x07,0xFF,0xF8,0x0F,0xFF,0xF8,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00},/*"l",76*/
{0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x10,0x08,0x00,0x20,0x00,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x10,0x08,0x00,0x20,0x00,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x00,0x08},/*"m",77*/
{0x00,0x00,0x00,0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x10,0x08,0x00,0x10,0x00,0x00,0x20,0x00,0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x1F,0xF8,0x00,0x00,0x08,0x00,0x00,0x00},/*"n",78*/
{0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x0F,0xF0,0x00,0x18,0x30,0x00,0x30,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x30,0x08,0x00,0x18,0x30,0x00,0x0F,0xF0,0x00,0x07,0xC0,0x00,0x00,0x00},/*"o",79*/
{0x00,0x00,0x00,0x00,0x20,0x01,0x00,0x3F,0xFF,0x00,0x3F,0xFF,0x00,0x10,0x11,0x00,0x20,0x09,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x30,0x38,0x00,0x1F,0xF0,0x00,0x0F,0xC0,0x00,0x00,0x00},/*"p",80*/
{0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x1F,0xF0,0x00,0x38,0x18,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x09,0x00,0x10,0x11,0x00,0x1F,0xFF,0x00,0x3F,0xFF,0x00,0x00,0x01,0x00,0x00,0x00},/*"q",81*/
{0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x08,0x08,0x00,0x10,0x08,0x00,0x20,0x08,0x00,0x20,0x00,0x00,0x30,0x00,0x00,0x30,0x00,0x00,0x00,0x00},/*"r",82*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0C,0x78,0x00,0x1E,0x18,0x00,0x33,0x08,0x00,0x23,0x08,0x00,0x21,0x08,0x00,0x21,0x88,0x00,0x21,0x98,0x00,0x30,0xF0,0x00,0x38,0x60,0x00,0x00,0x00},/*"s",83*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0xFF,0xF0,0x03,0xFF,0xF8,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x00,0x30,0x00,0x00,0x00,0x00,0x00,0x00},/*"t",84*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x3F,0xF0,0x00,0x7F,0xF8,0x00,0x00,0x18,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x20,0x10,0x00,0x3F,0xF8,0x00,0x7F,0xF0,0x00,0x00,0x10,0x00,0x00,0x00},/*"u",85*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x30,0x00,0x00,0x3C,0x00,0x00,0x3F,0x80,0x00,0x23,0xF0,0x00,0x00,0x78,0x00,0x00,0x70,0x00,0x23,0x80,0x00,0x3C,0x00,0x00,0x30,0x00,0x00,0x20,0x00},/*"v",86*/
{0x00,0x20,0x00,0x00,0x3C,0x00,0x00,0x3F,0xE0,0x00,0x23,0xF8,0x00,0x00,0xE0,0x00,0x27,0x00,0x00,0x3E,0x00,0x00,0x3F,0xE0,0x00,0x21,0xF8,0x00,0x01,0xE0,0x00,0x3E,0x00,0x00,0x20,0x00},/*"w",87*/
{0x00,0x00,0x00,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x38,0x38,0x00,0x3E,0x68,0x00,0x27,0x80,0x00,0x03,0xC8,0x00,0x2C,0xF8,0x00,0x38,0x38,0x00,0x20,0x18,0x00,0x20,0x08,0x00,0x00,0x00},/*"x",88*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x30,0x03,0x00,0x3C,0x01,0x00,0x3F,0x83,0x00,0x23,0xEC,0x00,0x00,0x70,0x00,0x23,0x80,0x00,0x3C,0x00,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0x00,0x00},/*"y",89*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x38,0x08,0x00,0x20,0x38,0x00,0x20,0xF8,0x00,0x23,0xE8,0x00,0x2F,0x88,0x00,0x3E,0x08,0x00,0x38,0x08,0x00,0x20,0x18,0x00,0x00,0x70,0x00,0x00,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x14,0x00,0x1F,0xF7,0xFC,0x30,0x00,0x06,0x20,0x00,0x02,0x00,0x00,0x00,0x00,0x00,0x00},/*"{",91*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"|",92*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x02,0x30,0x00,0x06,0x1F,0xF7,0xFC,0x00,0x14,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"}",93*/
{0x00,0x00,0x00,0x18,0x00,0x00,0x60,0x00,0x00,0x40,0x00,0x00,0x40,0x00,0x00,0x20,0x00,0x00,0x10,0x00,0x00,0x08,0x00,0x00,0x04,0x00,0x00,0x04,0x00,0x00,0x0C,0x00,0x00,0x10,0x00,0x00},/*"~",94*/
};
//32*32 ASCII字符集点阵
const unsigned char asc2_3216[95][128]={
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0xF0,0x00,0xC0,0x07,0xFF,0xE1,0xE0,0x07,0xF0,0x01,0xE0,0x00,0x00,0x00,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"!",1*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x01,0xC0,0x00,0x00,0x07,0x80,0x00,0x00,0x1F,0x00,0x00,0x00,0x1E,0x00,0x00,0x00,0x1C,0x20,0x00,0x00,0x01,0xC0,0x00,0x00,0x07,0x80,0x00,0x00,0x1F,0x00,0x00,0x00,0x1E,0x00,0x00,0x00,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*""",2*/
{0x00,0x00,0x00,0x00,0x00,0x18,0x0C,0x00,0x00,0x18,0x0C,0x00,0x00,0x18,0x0F,0xE0,0x00,0x1F,0xFC,0x00,0x03,0xF8,0x0C,0x00,0x00,0x18,0x0C,0x00,0x00,0x18,0x0C,0x00,0x00,0x18,0x0C,0x00,0x00,0x18,0x0C,0x00,0x00,0x18,0x0F,0xE0,0x00,0x1F,0xFC,0x00,0x03,0xF8,0x0C,0x00,0x00,0x18,0x0C,0x00,0x00,0x18,0x0C,0x00,0x00,0x00,0x00,0x00},/*"#",3*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x80,0x00,0x78,0x07,0xC0,0x00,0xFC,0x06,0x40,0x01,0x0E,0x00,0x20,0x03,0x07,0x00,0x20,0x02,0x03,0x80,0x20,0x0F,0xFF,0xFF,0xFC,0x02,0x01,0xC0,0x20,0x02,0x00,0xE0,0x60,0x01,0x30,0x70,0x40,0x01,0xF0,0x3F,0x80,0x00,0xF0,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"$",4*/
{0x00,0xFE,0x00,0x00,0x01,0xFF,0x00,0x00,0x03,0x01,0x80,0x00,0x02,0x00,0x80,0x60,0x03,0x01,0x81,0xC0,0x01,0xFF,0x07,0x00,0x00,0xFE,0x18,0x00,0x00,0x00,0xE0,0x00,0x00,0x03,0xBF,0x00,0x00,0x0C,0xFF,0xC0,0x00,0x71,0x80,0x60,0x01,0xC1,0x00,0x20,0x03,0x01,0x80,0x60,0x00,0x00,0xFF,0xC0,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,0x00},/*"%",5*/
{0x00,0x00,0x1F,0x00,0x00,0x00,0x7F,0xC0,0x00,0xFC,0xC0,0xC0,0x01,0xFF,0x80,0x60,0x03,0x03,0xE0,0x20,0x02,0x02,0x78,0x20,0x02,0x06,0x1E,0x20,0x03,0xFC,0x07,0x40,0x01,0xF0,0x03,0x80,0x00,0x01,0x03,0xC0,0x00,0x01,0x1C,0x60,0x00,0x01,0xE0,0x20,0x00,0x01,0x00,0x20,0x00,0x01,0x00,0x40,0x00,0x00,0x01,0x80,0x00,0x00,0x00,0x00},/*"&",6*/
{0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x1C,0x60,0x00,0x00,0x1C,0x40,0x00,0x00,0x1F,0x80,0x00,0x00,0x0F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0xF8,0x00,0x00,0x3F,0xFF,0x00,0x00,0x78,0x07,0xC0,0x01,0xC0,0x00,0xE0,0x03,0x00,0x00,0x30,0x04,0x00,0x00,0x08,0x08,0x00,0x00,0x04,0x10,0x00,0x00,0x02,0x00,0x00,0x00,0x00},/*"(",8*/
{0x00,0x00,0x00,0x00,0x10,0x00,0x00,0x02,0x08,0x00,0x00,0x04,0x04,0x00,0x00,0x08,0x03,0x00,0x00,0x30,0x01,0xC0,0x00,0xE0,0x00,0x78,0x07,0xC0,0x00,0x3F,0xFF,0x00,0x00,0x07,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*")",9*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0C,0x18,0x00,0x00,0x0E,0x38,0x00,0x00,0x0E,0x38,0x00,0x00,0x06,0x30,0x00,0x00,0x03,0x60,0x00,0x00,0x61,0x43,0x80,0x00,0xFF,0xFF,0x80,0x00,0x61,0x43,0x00,0x00,0x03,0x60,0x00,0x00,0x06,0x30,0x00,0x00,0x0E,0x38,0x00,0x00,0x0E,0x38,0x00,0x00,0x0C,0x18,0x00,0x00,0x00,0x00,0x00},/*"*",10*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x7F,0xFF,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00},/*"+",11*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0xE3,0x00,0x00,0x00,0xE2,0x00,0x00,0x00,0xFC,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*",",12*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00},/*"-",13*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xC0,0x00,0x00,0x01,0xE0,0x00,0x00,0x01,0xE0,0x00,0x00,0x00,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0C,0x00,0x00,0x00,0x38,0x00,0x00,0x00,0xE0,0x00,0x00,0x03,0x80,0x00,0x00,0x0E,0x00,0x00,0x00,0x38,0x00,0x00,0x00,0xE0,0x00,0x00,0x03,0x80,0x00,0x00,0x0E,0x00,0x00,0x00,0x38,0x00,0x00,0x00,0xE0,0x00,0x00,0x03,0x80,0x00,0x00,0x0E,0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"/",15*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0xF8,0x00,0x00,0x7F,0xFF,0x00,0x00,0xF0,0x07,0x80,0x01,0x80,0x00,0xC0,0x03,0x00,0x00,0x60,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0x00,0x00,0x60,0x01,0x80,0x00,0xC0,0x00,0xE0,0x03,0x80,0x00,0x7F,0xFF,0x00,0x00,0x0F,0xF8,0x00,0x00,0x00,0x00,0x00},/*"0",16*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x00,0x20,0x00,0x80,0x00,0x20,0x00,0x80,0x00,0x20,0x00,0x80,0x00,0x60,0x01,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x00,0x00,0x00,0x60,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"1",17*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x78,0x00,0xE0,0x00,0x98,0x01,0x60,0x01,0x00,0x02,0x60,0x02,0x00,0x04,0x60,0x02,0x00,0x08,0x60,0x02,0x00,0x10,0x60,0x02,0x00,0x20,0x60,0x02,0x00,0x40,0x60,0x03,0x00,0x80,0x60,0x01,0x83,0x00,0x60,0x01,0xFE,0x00,0xE0,0x00,0x7C,0x07,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"2",18*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF0,0x07,0x80,0x01,0xF0,0x07,0xC0,0x01,0x00,0x00,0x40,0x02,0x00,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x03,0x03,0x80,0x20,0x01,0x86,0x80,0x40,0x01,0xFC,0xC0,0xC0,0x00,0x78,0x7F,0x80,0x00,0x00,0x1E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"3",19*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x00,0x38,0x00,0x00,0x00,0x48,0x00,0x00,0x01,0x88,0x00,0x00,0x06,0x08,0x00,0x00,0x0C,0x08,0x10,0x00,0x30,0x08,0x10,0x00,0x40,0x08,0x10,0x01,0xFF,0xFF,0xF0,0x03,0xFF,0xFF,0xF0,0x03,0xFF,0xFF,0xF0,0x00,0x00,0x08,0x10,0x00,0x00,0x08,0x10,0x00,0x00,0x08,0x10,0x00,0x00,0x00,0x00},/*"4",20*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x80,0x00,0x1F,0x86,0x40,0x03,0xE1,0x00,0x20,0x03,0x02,0x00,0x20,0x03,0x04,0x00,0x20,0x03,0x04,0x00,0x20,0x03,0x04,0x00,0x20,0x03,0x04,0x00,0x20,0x03,0x06,0x00,0x40,0x03,0x03,0x01,0xC0,0x03,0x01,0xFF,0x80,0x03,0x00,0x7E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"5",21*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0xFC,0x00,0x00,0x3F,0xFF,0x00,0x00,0x70,0xC3,0x80,0x00,0x81,0x80,0xC0,0x01,0x01,0x00,0x60,0x03,0x02,0x00,0x20,0x02,0x02,0x00,0x20,0x02,0x02,0x00,0x20,0x02,0x02,0x00,0x20,0x02,0x03,0x00,0x40,0x01,0xC1,0x80,0xC0,0x00,0xC0,0xFF,0x80,0x00,0x00,0x7E,0x00,0x00,0x00,0x00,0x00},/*"6",22*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF0,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0x80,0x00,0x00,0x03,0x00,0x00,0x00,0x03,0x00,0x07,0xE0,0x03,0x00,0x3F,0xE0,0x03,0x01,0xC0,0x00,0x03,0x06,0x00,0x00,0x03,0x18,0x00,0x00,0x03,0x60,0x00,0x00,0x03,0x80,0x00,0x00,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"7",23*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0x00,0x00,0x78,0x3F,0x80,0x00,0xFC,0x60,0xC0,0x01,0x8E,0xC0,0x40,0x03,0x07,0x80,0x20,0x02,0x03,0x00,0x20,0x02,0x01,0x80,0x20,0x02,0x01,0x80,0x20,0x02,0x01,0xC0,0x20,0x03,0x01,0xE0,0x40,0x01,0x86,0x70,0xC0,0x00,0xFC,0x3F,0x80,0x00,0x78,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"8",24*/
{0x00,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0xFF,0x81,0xC0,0x01,0xC0,0xC1,0xC0,0x01,0x00,0x60,0x20,0x02,0x00,0x20,0x20,0x02,0x00,0x20,0x20,0x02,0x00,0x20,0x20,0x02,0x00,0x20,0x60,0x02,0x00,0x40,0xC0,0x01,0x00,0xC1,0x80,0x00,0xC1,0x8F,0x00,0x00,0x7F,0xFE,0x00,0x00,0x1F,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0xC0,0x00,0x07,0x81,0xE0,0x00,0x07,0x81,0xE0,0x00,0x03,0x00,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x00,0x66,0x00,0x06,0x00,0x78,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*";",27*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x00,0x00,0x01,0xC0,0x00,0x00,0x03,0x60,0x00,0x00,0x06,0x30,0x00,0x00,0x0C,0x18,0x00,0x00,0x18,0x0C,0x00,0x00,0x30,0x06,0x00,0x00,0x60,0x03,0x00,0x00,0xC0,0x01,0x80,0x01,0x00,0x00,0x40,0x02,0x00,0x00,0x20,0x04,0x00,0x00,0x10,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"<",28*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x00,0x00,0x00},/*"=",29*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x00,0x10,0x02,0x00,0x00,0x20,0x01,0x00,0x00,0x40,0x00,0xC0,0x01,0x80,0x00,0x60,0x03,0x00,0x00,0x30,0x06,0x00,0x00,0x18,0x0C,0x00,0x00,0x0C,0x18,0x00,0x00,0x06,0x30,0x00,0x00,0x03,0x60,0x00,0x00,0x01,0xC0,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*">",30*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x78,0x00,0x00,0x01,0xF8,0x00,0x00,0x02,0x38,0x00,0x00,0x02,0x00,0x00,0x00,0x04,0x00,0x00,0xC0,0x04,0x00,0x79,0xE0,0x04,0x00,0x81,0xE0,0x04,0x01,0x00,0xC0,0x04,0x03,0x00,0x00,0x02,0x02,0x00,0x00,0x03,0x06,0x00,0x00,0x01,0xFC,0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00},/*"?",31*/
{0x00,0x00,0x00,0x00,0x00,0x0F,0xF8,0x00,0x00,0x3F,0xFE,0x00,0x00,0x70,0x07,0x80,0x00,0xC0,0x00,0xC0,0x01,0x01,0xF8,0x40,0x03,0x07,0xFC,0x20,0x02,0x1E,0x04,0x20,0x02,0x30,0x08,0x20,0x02,0x20,0x30,0x20,0x02,0x3F,0xFC,0x20,0x01,0x3F,0x04,0x40,0x01,0x80,0x0C,0xC0,0x00,0xE0,0x31,0x80,0x00,0x1F,0xC2,0x00,0x00,0x00,0x00,0x00},/*"@",32*/
{0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x60,0x00,0x00,0x03,0xE0,0x00,0x00,0x3E,0x20,0x00,0x03,0xE0,0x20,0x00,0x3E,0x20,0x00,0x03,0xE0,0x20,0x00,0x03,0x80,0x20,0x00,0x07,0xFC,0x20,0x00,0x00,0x3F,0xE0,0x00,0x00,0x03,0xFE,0x20,0x00,0x00,0x3F,0xE0,0x00,0x00,0x01,0xE0,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x00},/*"A",33*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x03,0x03,0x00,0x20,0x01,0x86,0x80,0x60,0x01,0xFC,0xC0,0xC0,0x00,0xF8,0x7F,0x80,0x00,0x00,0x1F,0x00,0x00,0x00,0x00,0x00},/*"B",34*/
{0x00,0x00,0x00,0x00,0x00,0x07,0xF8,0x00,0x00,0x3F,0xFF,0x00,0x00,0x70,0x07,0x80,0x00,0xC0,0x00,0xC0,0x01,0x00,0x00,0x40,0x03,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x01,0x00,0x00,0x40,0x01,0x80,0x00,0xC0,0x03,0xC0,0x01,0x80,0x00,0x30,0x06,0x00,0x00,0x00,0x00,0x00},/*"C",35*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0x00,0x00,0x60,0x01,0x00,0x00,0x40,0x01,0x80,0x00,0xC0,0x00,0xF0,0x07,0x80,0x00,0x7F,0xFE,0x00,0x00,0x0F,0xF8,0x00,0x00,0x00,0x00,0x00},/*"D",36*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x03,0x80,0x20,0x02,0x0F,0xE0,0x20,0x03,0x00,0x00,0x60,0x03,0xC0,0x00,0xE0,0x00,0x60,0x03,0x00,0x00,0x00,0x00,0x00},/*"E",37*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x00,0x02,0x01,0x00,0x00,0x02,0x01,0x00,0x00,0x02,0x01,0x00,0x00,0x02,0x03,0x80,0x00,0x03,0x0F,0xE0,0x00,0x03,0x00,0x00,0x00,0x03,0xC0,0x00,0x00,0x00,0x60,0x00,0x00},/*"F",38*/
{0x00,0x00,0x00,0x00,0x00,0x07,0xF8,0x00,0x00,0x3F,0xFE,0x00,0x00,0x70,0x07,0x80,0x01,0xC0,0x01,0xC0,0x01,0x00,0x00,0x40,0x03,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x01,0x00,0x20,0x20,0x01,0x00,0x20,0x40,0x03,0xC0,0x3F,0x80,0x00,0x30,0x3F,0x80,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00},/*"G",39*/
{0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0x80,0x20,0x02,0x00,0x80,0x20,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x02,0x00,0x80,0x20,0x02,0x00,0x80,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x00,0x00,0x00,0x00},/*"H",40*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"I",41*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0E,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0x01,0x02,0x00,0x00,0x01,0x02,0x00,0x00,0x01,0x02,0x00,0x00,0x03,0x02,0x00,0x00,0x06,0x03,0xFF,0xFF,0xFC,0x03,0xFF,0xFF,0xF8,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"J",42*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0xC0,0x20,0x02,0x01,0x00,0x20,0x00,0x07,0x80,0x00,0x00,0x0F,0xE0,0x00,0x00,0x30,0xF8,0x00,0x02,0x60,0x3E,0x20,0x03,0x80,0x0F,0x20,0x03,0x00,0x03,0xE0,0x02,0x00,0x00,0xE0,0x02,0x00,0x00,0x20,0x00,0x00,0x00,0x20},/*"K",43*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x60,0x00,0x00,0x00,0xE0,0x00,0x00,0x03,0x00,0x00,0x00,0x00,0x00},/*"L",44*/
{0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xE0,0x00,0x20,0x03,0xFF,0x00,0x20,0x00,0x1F,0xF0,0x00,0x00,0x01,0xFF,0x80,0x00,0x00,0x0F,0xE0,0x00,0x00,0x1E,0x00,0x00,0x03,0xE0,0x00,0x00,0x3E,0x00,0x20,0x03,0xE0,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20},/*"M",45*/
{0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0x80,0x00,0x20,0x03,0xF0,0x00,0x20,0x00,0xFC,0x00,0x00,0x00,0x1F,0x00,0x00,0x00,0x07,0xC0,0x00,0x00,0x01,0xF0,0x00,0x00,0x00,0x7C,0x00,0x02,0x00,0x1F,0x80,0x02,0x00,0x07,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"N",46*/
{0x00,0x00,0x00,0x00,0x00,0x0F,0xF8,0x00,0x00,0x3F,0xFE,0x00,0x00,0xF0,0x07,0x80,0x01,0x80,0x00,0xC0,0x01,0x00,0x00,0x40,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x01,0x00,0x00,0x40,0x01,0x80,0x00,0xC0,0x00,0xF0,0x03,0x80,0x00,0x3F,0xFE,0x00,0x00,0x0F,0xF8,0x00,0x00,0x00,0x00,0x00},/*"O",47*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0x80,0x20,0x02,0x00,0x80,0x20,0x02,0x00,0x80,0x00,0x02,0x00,0x80,0x00,0x02,0x00,0x80,0x00,0x02,0x00,0x80,0x00,0x03,0x01,0x80,0x00,0x01,0x83,0x00,0x00,0x00,0xFE,0x00,0x00,0x00,0x7C,0x00,0x00,0x00,0x00,0x00,0x00},/*"P",48*/
{0x00,0x00,0x00,0x00,0x00,0x0F,0xF8,0x00,0x00,0x7F,0xFF,0x00,0x00,0xF0,0x03,0x80,0x01,0x80,0x01,0xC0,0x01,0x00,0x06,0x40,0x02,0x00,0x04,0x20,0x02,0x00,0x04,0x20,0x02,0x00,0x06,0x20,0x02,0x00,0x03,0xE0,0x01,0x00,0x00,0xF8,0x01,0x80,0x00,0x5C,0x00,0xE0,0x03,0x8C,0x00,0x3F,0xFF,0x0C,0x00,0x0F,0xFC,0x18,0x00,0x00,0x00,0x00},/*"Q",49*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x01,0x00,0x20,0x02,0x01,0x00,0x20,0x02,0x01,0x80,0x00,0x02,0x01,0xE0,0x00,0x02,0x01,0xFC,0x00,0x03,0x03,0x3F,0x80,0x01,0x86,0x07,0xE0,0x01,0xFC,0x00,0xE0,0x00,0xF8,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x00},/*"R",50*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x78,0x06,0x00,0x00,0xFE,0x01,0xE0,0x01,0x86,0x00,0xC0,0x03,0x03,0x00,0x40,0x02,0x03,0x00,0x20,0x02,0x01,0x80,0x20,0x02,0x01,0x80,0x20,0x02,0x01,0xC0,0x20,0x02,0x00,0xC0,0x20,0x01,0x00,0xE0,0x60,0x01,0x80,0x70,0xC0,0x03,0xE0,0x3F,0x80,0x00,0x00,0x1F,0x00,0x00,0x00,0x00,0x00},/*"S",51*/
{0x00,0x00,0x00,0x00,0x00,0x60,0x00,0x00,0x03,0x80,0x00,0x00,0x03,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x03,0xFF,0xFF,0xE0,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x03,0x80,0x00,0x00,0x00,0xE0,0x00,0x00,0x00,0x00,0x00,0x00},/*"T",52*/
{0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x03,0xFF,0xFF,0x00,0x03,0xFF,0xFF,0xC0,0x02,0x00,0x00,0x40,0x02,0x00,0x00,0x60,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x02,0x00,0x00,0x40,0x02,0x00,0x00,0x80,0x03,0xFF,0xFF,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"U",53*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xFC,0x00,0x00,0x02,0x3F,0xC0,0x00,0x00,0x03,0xF8,0x00,0x00,0x00,0x7F,0x80,0x00,0x00,0x07,0xE0,0x00,0x00,0x07,0x80,0x00,0x00,0x78,0x00,0x02,0x03,0xC0,0x00,0x02,0x3C,0x00,0x00,0x03,0xC0,0x00,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00},/*"V",54*/
{0x02,0x00,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xFF,0x80,0x00,0x02,0x3F,0xFE,0x00,0x02,0x00,0x7F,0xE0,0x00,0x00,0x0F,0x00,0x02,0x00,0xF0,0x00,0x03,0xEF,0x00,0x00,0x03,0xFF,0x80,0x00,0x02,0x0F,0xFE,0x00,0x00,0x00,0x3F,0xE0,0x00,0x00,0x1F,0x00,0x02,0x07,0xE0,0x00,0x03,0xF8,0x00,0x00,0x03,0x00,0x00,0x00,0x02,0x00,0x00,0x00},/*"W",55*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0x80,0x00,0xE0,0x03,0xF0,0x03,0x20,0x02,0xFC,0x0C,0x20,0x02,0x1F,0x30,0x00,0x00,0x07,0xC0,0x00,0x00,0x07,0xF0,0x00,0x02,0x18,0x7C,0x00,0x02,0x60,0x1F,0x20,0x03,0x80,0x03,0xE0,0x02,0x00,0x00,0xE0,0x02,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x00},/*"X",56*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x03,0x00,0x00,0x00,0x03,0xC0,0x00,0x00,0x03,0xF8,0x00,0x00,0x02,0x3E,0x00,0x20,0x02,0x0F,0xC0,0x20,0x00,0x01,0xFF,0xE0,0x00,0x00,0x7F,0xE0,0x00,0x03,0x80,0x20,0x02,0x1C,0x00,0x20,0x02,0x70,0x00,0x00,0x03,0x80,0x00,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"Y",57*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x60,0x00,0xE0,0x03,0x80,0x03,0xE0,0x03,0x00,0x0F,0xA0,0x02,0x00,0x3E,0x20,0x02,0x00,0xF8,0x20,0x02,0x03,0xE0,0x20,0x02,0x0F,0x80,0x20,0x02,0x3E,0x00,0x20,0x02,0x78,0x00,0x20,0x03,0xE0,0x00,0x60,0x03,0x80,0x00,0xE0,0x02,0x00,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"Z",58*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0xFF,0xFF,0xFC,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"[",59*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x03,0xC0,0x00,0x00,0x00,0x78,0x00,0x00,0x00,0x1E,0x00,0x00,0x00,0x03,0xC0,0x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x1E,0x00,0x00,0x00,0x07,0x80,0x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x3C,0x00,0x00,0x00,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"\",60*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x10,0x00,0x00,0x04,0x1F,0xFF,0xFF,0xFC,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x08,0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x10,0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01},/*"_",63*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x10,0x00,0x00,0x00,0x10,0x00,0x00,0x00,0x10,0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x08,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x80,0x00,0x01,0x8F,0xC0,0x00,0x03,0x8C,0x60,0x00,0x06,0x18,0x20,0x00,0x04,0x10,0x20,0x00,0x04,0x10,0x20,0x00,0x04,0x20,0x20,0x00,0x04,0x20,0x40,0x00,0x06,0x20,0x40,0x00,0x03,0xFF,0xC0,0x00,0x01,0xFF,0xE0,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0xC0,0x00,0x00,0x00,0x00},/*"a",65*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x03,0xFF,0xFF,0xE0,0x07,0xFF,0xFF,0xC0,0x00,0x01,0x80,0xC0,0x00,0x02,0x00,0x60,0x00,0x02,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x06,0x00,0x40,0x00,0x03,0x00,0xC0,0x00,0x01,0xFF,0x80,0x00,0x00,0xFE,0x00,0x00,0x00,0x00,0x00},/*"b",66*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7E,0x00,0x00,0x01,0xFF,0x80,0x00,0x03,0x81,0xC0,0x00,0x02,0x00,0x40,0x00,0x06,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x06,0x00,0x20,0x00,0x03,0xC0,0x40,0x00,0x01,0xC0,0x80,0x00,0x00,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"c",67*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7E,0x00,0x00,0x01,0xFF,0x80,0x00,0x03,0x80,0xC0,0x00,0x06,0x00,0x60,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x02,0x04,0x00,0x40,0x02,0x02,0x00,0x80,0x03,0xFF,0xFF,0xE0,0x07,0xFF,0xFF,0xC0,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x00},/*"d",68*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7E,0x00,0x00,0x01,0xFF,0x80,0x00,0x03,0x11,0xC0,0x00,0x02,0x10,0x40,0x00,0x04,0x10,0x60,0x00,0x04,0x10,0x20,0x00,0x04,0x10,0x20,0x00,0x04,0x10,0x20,0x00,0x06,0x10,0x20,0x00,0x03,0x10,0x40,0x00,0x01,0xF0,0xC0,0x00,0x00,0x71,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"e",69*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x7F,0xFF,0xE0,0x01,0xFF,0xFF,0xE0,0x01,0x04,0x00,0x20,0x03,0x04,0x00,0x20,0x02,0x04,0x00,0x20,0x02,0x04,0x00,0x20,0x02,0x04,0x00,0x00,0x02,0x00,0x00,0x00,0x01,0xC0,0x00,0x00,0x01,0xC0,0x00,0x00},/*"f",70*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1C,0x00,0x00,0xE3,0x3E,0x00,0x03,0xFF,0xC2,0x00,0x02,0x0C,0xC3,0x00,0x04,0x04,0xC1,0x00,0x04,0x04,0xC1,0x00,0x04,0x04,0xC1,0x00,0x04,0x04,0xC1,0x00,0x06,0x0C,0xC1,0x00,0x03,0xF8,0xC3,0x00,0x05,0xF0,0x62,0x00,0x06,0x00,0x7E,0x00,0x06,0x00,0x3C,0x00,0x00,0x00,0x00},/*"g",71*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x07,0xFF,0xFF,0xE0,0x00,0x01,0x00,0x20,0x00,0x02,0x00,0x20,0x00,0x06,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x20,0x00,0x06,0x00,0x20,0x00,0x03,0xFF,0xE0,0x00,0x01,0xFF,0xE0,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20},/*"h",72*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x03,0x87,0xFF,0xE0,0x03,0x8F,0xFF,0xE0,0x03,0x80,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"i",73*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x04,0x00,0x01,0x00,0x04,0x00,0x01,0x00,0x04,0x00,0x03,0x00,0x04,0x00,0x06,0x03,0x87,0xFF,0xFC,0x03,0x8F,0xFF,0xF8,0x03,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"j",74*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x07,0xFF,0xFF,0xE0,0x00,0x00,0x08,0x20,0x00,0x00,0x10,0x20,0x00,0x00,0x30,0x00,0x00,0x00,0xFC,0x00,0x00,0x05,0x8E,0x00,0x00,0x07,0x07,0xA0,0x00,0x06,0x01,0xE0,0x00,0x04,0x00,0xE0,0x00,0x04,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x00},/*"k",75*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x02,0x00,0x00,0x20,0x03,0xFF,0xFF,0xE0,0x07,0xFF,0xFF,0xE0,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"l",76*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x20,0x00,0x07,0xFF,0xE0,0x00,0x0F,0xFF,0xE0,0x00,0x02,0x00,0x20,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x20,0x00,0x07,0xFF,0xE0,0x00,0x03,0xFF,0xE0,0x00,0x02,0x00,0x20,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x20,0x00,0x07,0xFF,0xE0,0x00,0x03,0xFF,0xE0,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x00},/*"m",77*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x07,0xFF,0xE0,0x00,0x0F,0xFF,0xE0,0x00,0x01,0x00,0x20,0x00,0x02,0x00,0x20,0x00,0x02,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x20,0x00,0x06,0x00,0x20,0x00,0x03,0xFF,0xE0,0x00,0x01,0xFF,0xE0,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20},/*"n",78*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7E,0x00,0x00,0x00,0xFF,0x80,0x00,0x03,0x81,0xC0,0x00,0x02,0x00,0x40,0x00,0x06,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x06,0x00,0x20,0x00,0x02,0x00,0x40,0x00,0x03,0x81,0xC0,0x00,0x01,0xFF,0x80,0x00,0x00,0x7E,0x00,0x00,0x00,0x00,0x00},/*"o",79*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x01,0x00,0x04,0x00,0x01,0x00,0x07,0xFF,0xFF,0x00,0x0F,0xFF,0xFF,0x00,0x01,0x00,0xC1,0x00,0x02,0x00,0x41,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x06,0x00,0x40,0x00,0x03,0x01,0xC0,0x00,0x01,0xFF,0x80,0x00,0x00,0x7E,0x00,0x00,0x00,0x00,0x00},/*"p",80*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7E,0x00,0x00,0x01,0xFF,0x80,0x00,0x03,0x80,0xC0,0x00,0x02,0x00,0x60,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x02,0x00,0x41,0x00,0x03,0x00,0xC1,0x00,0x03,0xFF,0xFF,0x00,0x07,0xFF,0xFF,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01},/*"q",81*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x0F,0xFF,0xE0,0x00,0x0F,0xFF,0xE0,0x00,0x00,0xC0,0x20,0x00,0x01,0x00,0x20,0x00,0x02,0x00,0x20,0x00,0x06,0x00,0x20,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x03,0x00,0x00,0x00,0x00,0x00,0x00},/*"r",82*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0xE0,0x00,0x01,0xC0,0xE0,0x00,0x03,0xE0,0x40,0x00,0x06,0x30,0x20,0x00,0x04,0x30,0x20,0x00,0x04,0x18,0x20,0x00,0x04,0x18,0x20,0x00,0x04,0x18,0x20,0x00,0x04,0x0C,0x20,0x00,0x02,0x0C,0x60,0x00,0x03,0x07,0xC0,0x00,0x07,0x83,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"s",83*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x0C,0x00,0x00,0x00,0x1F,0xFF,0x80,0x00,0xFF,0xFF,0xC0,0x00,0x04,0x00,0x60,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x40,0x00,0x00,0x01,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"t",84*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x07,0xFF,0x80,0x00,0x0F,0xFF,0xC0,0x00,0x00,0x00,0x60,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x04,0x00,0x40,0x00,0x04,0x00,0x80,0x00,0x07,0xFF,0xE0,0x00,0x0F,0xFF,0xC0,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x40},/*"u",85*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x07,0x80,0x00,0x00,0x07,0xF0,0x00,0x00,0x04,0xFE,0x00,0x00,0x04,0x1F,0xC0,0x00,0x00,0x03,0xE0,0x00,0x00,0x03,0x80,0x00,0x00,0x1C,0x00,0x00,0x04,0x60,0x00,0x00,0x07,0x80,0x00,0x00,0x06,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"v",86*/
{0x00,0x04,0x00,0x00,0x00,0x06,0x00,0x00,0x00,0x07,0xC0,0x00,0x00,0x07,0xFC,0x00,0x00,0x04,0x3F,0x80,0x00,0x00,0x03,0xE0,0x00,0x04,0x0F,0x80,0x00,0x06,0xF0,0x00,0x00,0x07,0xF0,0x00,0x00,0x07,0xFF,0x80,0x00,0x04,0x0F,0xE0,0x00,0x00,0x03,0x80,0x00,0x04,0x3C,0x00,0x00,0x07,0xC0,0x00,0x00,0x06,0x00,0x00,0x00,0x04,0x00,0x00},/*"w",87*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x04,0x00,0x20,0x00,0x04,0x00,0x60,0x00,0x07,0x00,0xE0,0x00,0x07,0x83,0x20,0x00,0x07,0xE6,0x00,0x00,0x04,0xF8,0x00,0x00,0x00,0x3C,0x00,0x00,0x04,0x5E,0x20,0x00,0x05,0x87,0xA0,0x00,0x06,0x01,0xE0,0x00,0x04,0x00,0x60,0x00,0x04,0x00,0x20,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x00},/*"x",88*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x03,0x00,0x07,0x00,0x03,0x00,0x07,0xE0,0x01,0x00,0x04,0xF8,0x01,0x00,0x04,0x1F,0x02,0x00,0x00,0x07,0xFC,0x00,0x00,0x00,0xE0,0x00,0x00,0x07,0x00,0x00,0x04,0x38,0x00,0x00,0x07,0xC0,0x00,0x00,0x06,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x00,0x00,0x00},/*"y",89*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x80,0x60,0x00,0x06,0x00,0xE0,0x00,0x04,0x03,0xE0,0x00,0x04,0x07,0xA0,0x00,0x04,0x0E,0x20,0x00,0x04,0x3C,0x20,0x00,0x04,0x70,0x20,0x00,0x05,0xE0,0x20,0x00,0x07,0x80,0x20,0x00,0x07,0x00,0x60,0x00,0x04,0x00,0xE0,0x00,0x00,0x03,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x01,0x40,0x00,0x07,0xFE,0x3F,0xF8,0x08,0x00,0x00,0x04,0x10,0x00,0x00,0x02,0x10,0x00,0x00,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"{",91*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"|",92*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x10,0x00,0x00,0x02,0x10,0x00,0x00,0x02,0x08,0x00,0x00,0x04,0x07,0xFE,0x3F,0xF8,0x00,0x01,0x40,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"}",93*/
{0x00,0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x30,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x30,0x00,0x00,0x00,0x08,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x02,0x00,0x00,0x00,0x0C,0x00,0x00,0x00,0x18,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"~",94*/
};
#endif
向工程中添加.c/.h文件的步骤请阅读“STM32CubeMX教程19 I2C - MPU6050驱动”实验3.2.3小节
值得提醒的是在LCD初始化函数中使用串口打印了LCD的控制芯片ID，因此如果未初始化串口请注释掉该输出代码，如果你不希望注释，请阅读“STM32CubeMX教程9 USART/UART 异步通信”配置并重定向串口
然后在主函数中添加一些用于测试LCD是否正常工作的函数，具体源代码如下所示
/*LCD测试函数*/
void LCD_TEST(void)
{
/*画线测试*/
testlines();
HAL_Delay(1000);
/*画正方形测试*/
testdrawrects();
HAL_Delay(1000);
/*画圆测试*/
testfillcircles(15);
HAL_Delay(1000);
/*字体测试*/
tftPrintTest();
}
/*画线测试*/
void testlines(void)
{
LCD_Clear(WHITE);
POINT_COLOR=BLACK;
for (int16_t x=0; x < SSD_VER_RESOLUTION; x+=6)
{
LCD_DrawLine(0, 0, x, SSD_HOR_RESOLUTION-1);
HAL_Delay(3);
}
for (int16_t y=0; y < SSD_HOR_RESOLUTION; y+=6)
{
LCD_DrawLine(0, 0, SSD_VER_RESOLUTION-1, y);
HAL_Delay(3);
}
LCD_Clear(WHITE);
POINT_COLOR=BLUE;
for (int16_t x=0; x < SSD_VER_RESOLUTION; x+=6)
{
LCD_DrawLine(SSD_VER_RESOLUTION-1, 0, x, SSD_HOR_RESOLUTION-1);
HAL_Delay(3);
}
for (int16_t y=0; y < SSD_HOR_RESOLUTION; y+=6)
{
LCD_DrawLine(SSD_VER_RESOLUTION-1, 0, 0, y);
HAL_Delay(3);
}
LCD_Clear(WHITE);
POINT_COLOR=RED;
for (int16_t y=0; y < SSD_HOR_RESOLUTION; y+=6)
{
LCD_DrawLine(0, SSD_HOR_RESOLUTION-1, SSD_VER_RESOLUTION-1, y);
HAL_Delay(3);
}
for (int16_t x=0; x < SSD_VER_RESOLUTION; x+=6)
{
LCD_DrawLine(0, SSD_HOR_RESOLUTION-1, x, 0);
HAL_Delay(3);
}
LCD_Clear(WHITE);
POINT_COLOR=MAGENTA;
for (int16_t x=0; x < SSD_VER_RESOLUTION; x+=6)
{
LCD_DrawLine(SSD_VER_RESOLUTION-1, SSD_HOR_RESOLUTION-1, x, 0);
HAL_Delay(3);
}
for (int16_t y=0; y < SSD_HOR_RESOLUTION; y+=6)
{
LCD_DrawLine(SSD_VER_RESOLUTION-1, SSD_HOR_RESOLUTION-1, 0, y);
HAL_Delay(3);
}
}
/*画正方形测试*/
void testdrawrects(void)
{
LCD_Clear(WHITE);
POINT_COLOR=BLACK;
for (int16_t x=0; x < SSD_VER_RESOLUTION; x+=6)
{
LCD_DrawRectangle(SSD_VER_RESOLUTION/2 -x/2, SSD_HOR_RESOLUTION/2 -x/2 , x, x);
}
}
/*画圆测试*/
void testfillcircles(uint8_t radius)
{
LCD_Clear(WHITE);
POINT_COLOR=BLUE;
for(int16_t x=radius; x < SSD_VER_RESOLUTION; x+=radius*2)
{
for(int16_t y=radius; y < SSD_HOR_RESOLUTION; y+=radius*2)
{
LCD_Draw_Circle(x, y, radius);
}
}
HAL_Delay(1500);
LCD_Clear(WHITE);
POINT_COLOR=MAGENTA;
radius = radius / 2;
for(int16_t x=radius; x < SSD_VER_RESOLUTION; x+=radius*2)
{
for(int16_t y=radius; y < SSD_HOR_RESOLUTION; y+=radius*2)
{
LCD_Draw_Circle(x, y, radius);
}
}
}
/*字体测试*/
void tftPrintTest(void)
{
LCD_Clear(WHITE);
LCD_SetCursor(0, 30);
POINT_COLOR=RED;
LCD_ShowString(0,30,200,16,16,(uint8_t *)"Hello World!");
POINT_COLOR=YELLOW;
LCD_ShowString(0,60,200,16,24,(uint8_t *)"Hello World!");
POINT_COLOR=GREEN;
LCD_ShowString(0,90,200,16,32,(uint8_t *)"Hello World!");
POINT_COLOR=BLUE;
LCD_ShowxNum(0,120,1234,4,24,1);
HAL_Delay(1500);
POINT_COLOR=YELLOW;
LCD_ShowString(0,180,200,16,24,(uint8_t *)"Hello World!");
POINT_COLOR=GREEN;
LCD_ShowString(0,210,200,16,32,(uint8_t *)" Want pi?");
LCD_ShowString(0,240,200,16,32,(uint8_t *)" Print HEX!");
POINT_COLOR=BLUE;
LCD_ShowString(0,270,200,16,16,(uint8_t *)"Sketch has been");
LCD_ShowString(0,300,200,16,24,(uint8_t *)"running for: ");
POINT_COLOR=MAGENTA;
LCD_ShowString(0,330,200,16,24,(uint8_t *)" seconds.");
}
在main.c中声明这些用于测试的函数
void LCD_TEST(void);
void testlines(void);
void testdrawrects(void);
void testfillcircles(uint8_t radius);
void tftPrintTest(void);
最后在主函数中对LCD初始化，在主循环中周期调用测试函数即可，具体源代码如下所示
/*主循环外程序*/
//这个延时在FSMC初始化之后LCD初始化之前，必须要有
HAL_Delay(50);
LCD_Init();
/*主循环内程序*/
LCD_TEST();
HAL_Delay(4000);
4、烧录验证
烧录程序，开发板上电后，LCD会依次测试画线、画矩形、画圆和字符输出功能，具体现象如下图所示
5、注释详解
注释1：图片来源 STM32F4xx 中文参考手册 RM009
注释2：图片来源 https://github.com/hampussandberg/HexConnect/wiki/LCD-ER_TFTM070_5
注释3：图片来源 STM32Cube高效开发教程（基础篇）
注释4：NT35510数据手册来源 https://www.waveshare.com/w/upload/a/a8/NT35510.pdf
注释5：IL9341数据手册来源 https://cdn-shop.adafruit.com/datasheets/ILI9341.pdf文章来源：https://www.toymoban.com/news/detail-817760.html
注释6：NT35510芯片LCD驱动程序来自正点原子文章来源地址https://www.toymoban.com/news/detail-817760.html
到了这里，关于STM32CubeMX教程22 FSMC - 8080并行接口TFT-LCD驱动的文章就介绍完了。如果您还想了解更多内容，请在右上角搜索TOY模板网以前的文章或继续浏览下面的相关文章，希望大家以后多多支持TOY模板网！
